Favorite SAK/multitool combos
-
Mine's recently been more of a SAK/Multitool/Spydie combo, party due to UK knife laws:
Leatherman Knifeless Fuse and Victorinox Wrench/Bit holder (I tried, but didn't get on with the Leatherman bits) - this goes in my bag (usually a bike pannier or "man bag" if walking)
Spyderco Edge Matters forum Pingu with K390 steel (non-locking knife) - in one of my main trouser pockets
Victorinox Alox Rambler (in my trouser coin pocket)
Have most bases covered here, though am missing an awl (covered if I replace the Pingu with my Vic Soldier) and saw (guess a Farmer would cover that, though I only really need a saw if camping)
Apologies for bad phone camera photo:

-
Since receiving a CrossGrip last week, this has been my favorite minimalist combo:

SAK Manager (with toothpick instead of tweezers) with SOG CrossGrip and a Screw Key
-
@theonew said:
Since receiving a CrossGrip last week, this has been my favorite minimalist combo:
SAK Manager (with toothpick instead of tweezers) with SOG CrossGrip and a Screw Key
Oh, I've got one of those, but have been put off carrying it as it arrived (new) with a completely blunt (I mean really, really blunt) knife with a one-side chisel grind and I've never got around to trying to sharpen it. What's the best way to sharpen such a blade? The little pliers on it a spring loaded and it's otherwise quite a sweet little tool.
-
Mine was completely dull as well and also the bevel that was ground in varied over the length of the blade, starting at around 40 degrees for the first third and then tapering down to about 30. The variable bevel didn't really bother me as I've done that with blades intentionally to keep a sturdier edge near the area where the most force can be applied but I've found using a round rod sharpener to be the best way to sharpen it since it is easier to follow the "curve".
But to be honest I will slowly over time turn this into a regular v-bevel and have already started sharpening the other side. If you want to quickly put an edge on the blade and don't mind transitioning to a v-bevel start sharpening the flat side by holding it up a few degrees so that you are only contacting a small area of the bevel. You should be able to get it serviceably sharp in a very short amount of time this way. Hope that helps.
-
-
@theonew said:
Mine was completely dull as well and also the bevel that was ground in varied over the length of the blade, starting at around 40 degrees for the first third and then tapering down to about 30. The variable bevel didn't really bother me as I've done that with blades intentionally to keep a sturdier edge near the area where the most force can be applied but I've found using a round rod sharpener to be the best way to sharpen it since it is easier to follow the "curve".But to be honest I will slowly over time turn this into a regular v-bevel and have already started sharpening the other side. If you want to quickly put an edge on the blade and don't mind transitioning to a v-bevel start sharpening the flat side by holding it up a few degrees so that you are only contacting a small area of the bevel. You should be able to get it serviceably sharp in a very short amount of time this way. Hope that helps.
Okay, I'll probably give that a go, would prefer a regular v-bevel - I have a Spyderco Sharpmaker, so would prefer to just have a 40 degree angle on a v-bevel all round
-
Again today:


-
Ultra heavy + ultra light

-
Where's the SAK, Poncho?
-
Poor Poncho is out of practice after vacation

-
Whatever do you guys mean


-
:P
-
-
-
Like that OHT + Pioneer X!
Have to try it out too!
I decided to go with Wave+111mm.
Similar tools, but these Vic phillips and Wave pliers are what I needed at the same time...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





