Victorinox Executive?
-
I like the Executive and I have it permanently in my travel shaving essentials bag (which I use at home too). I use it at least weekly, have used everything save the orange peeler (oranges are among the few things you can't find in our bathroom).
If there was a kind of Executivechamp I would buy that too.Where's the hook?

-
One thing to note, before everyone goes cutting a bottle opener into the peeler: That is the part of the shank that handles the torque load for the screwdriver tip. So if you ever want to use the screwdriver to apply any decent amount of torque, forget this mod.
-
Here's a trip down memory lane.... Browsing through the guestbook on SAKcollector.com I found my own entry of more than ten years ago:
"Two pieces of fruit every day are essential for a good health. Enter the Executive. Its two long and slender blades are ideally shaped for slicing apples and peeling oranges. This little gem is THE fruitknife for SAK fruitcakes."
Things have changed. Between then and now I worked three years for a large multinational company trading mostly citrus fruit and banananas (I know how to spell it, just not when to stop) where I learned eating oranges the farmer's way: simply quartering them and gnawing the flesh out of the peel. Not exactly good manners, but it works. No need for peeling. Anyhow, these days I don't do either. Squeezing oranges for their juice is my preferred method now.
At the time I liked the Executive very much. Still do, I have three of them and although I do not carry one there's always one within reach on my desk.
-
@Ronald Schröder said:
Things have changed. Between then and now I worked three years for a large multinational company trading mostly citrus fruit and banananas (I know how to spell it, just not when to stop) where I learned eating oranges the farmer's way: simply quartering them and gnawing the flesh out of the peel. Not exactly good manners, but it works. No need for peeling.Also the traditional method of eating your half-time orange for football (soccer) players!
-
I believe I will carry my Executive cause of this thread this weekend


-
-
I believe I will carry my Executive cause of this thread this weekend


Mine just lives on my keys. :)
Hahah mine too



-
-
Been searching for one and looking at this thread didn't help at all trying to forget it. I had one long time ago in late 80s but lost it. I just cannot find any in reasonable cost with shipping counted in. Some day... :)
-
@Padre said:
Been searching for one and looking at this thread didn't help at all trying to forget it. I had one long time ago in late 80s but lost it. I just cannot find any in reasonable cost with shipping counted in. Some day... :)They are very good for there size for sure
I have neglected mine lately for bigger more feature dense models
:D I think I may give it some pocket time this weekend or if I go out anywhere after works in the evening this week 
-
Getting constant pocket time as of late, it's going to be the whole winter with me for sure.

Appreciating it much more now! -
@ThePeacent said:
Getting constant pocket time as of late, it's going to be the whole winter with me for sure.
Appreciating it much more now!Glad it is getting pocket time Peacent
The Executive is truly a great SAK

-
Nice pic Peacent!

Did you fix yours or get a new one?
Or was it you that had problems with the scissors? -
@Mizedog said:
I like mine, but ye scissor spring keeps moving to the side, and off the scissors which quickly collapses the scissors, and doesn't let them reopen. Does anyone else have this problem? This doesn't happen with my money clip which is the same size. This issue causes enough frustration that I don't carry the knife.Sent from my SAMSUNG-SM-N900A using Tapatalk
The "newer" scissors have a groove under the moving handle for the spring to follow (this design change was some years ago). The old scissors do not and the spring rides on the flat. If the spring is twisted or otherwise malformed slightly it may not track the moving handle well. On the old scissors without the groove it will slip off more easily. The design change was made to address this problem. The more it slips off and gets crunched, the more it can become deformed which increases occurrence frequency. First thing to check is how tight the scissors are. If they're loose enough, the lateral movement of the moving handle can be part of the problem. The scissors are robust to this, so if anything it's a contributor, not the proximate cause. Scissors with screws are simpler to deal with using a jewelers driver. Riveted scissors are not so simple. It takes a flat punch or pin drift (not a pointed center punch), small hammer and a small anvil (like the kind found on the back of a small jewelers bench vise). Peening the rivet with the hammer and flat punch should be done lightly, very, very gradually tightening it. Make the rivet too tight and you'll have a devil of a time getting it to loosen up.
I've had the spring alignment problem with some older 91mm, and on one occasion with an old 58mm. Takes some patience and a small pair of jeweler size needle nose with smooth jaws to adjust the spring mounting and reform its shape. If you don't have or cannot get a pair with smooth jaws, pad serrated jaws with soft cloth. The serrations can nick a spring creating a weak spot. Do this when you have sufficient time to work at it methodically. Patience and careful observation are key. First thing to look for is whether its attachment is centered in the hole and the first part of it from there to the bend lines up with the fixed handle. The next thing to observe is how well the end of the spring tracks on the moving handle. I've had springs line up perfectly when the scissors jaws are open and the end move laterally halfway off the scissors handle when the jaws are closed. Usual issue is a twisted spring, sometimes twisted at the sharp bend in the middle where the spring flexes the most. The first few times I did this it took a while to observe the effect various tweaks made on spring tracking. If all else fails in aligning one to track correctly, throw in the towel and replace the spring. I've never had to do that, but came very close to it with a Deluxe Tinker that was delivered with a badly twisted spring.
John
-
This just arrived.
I'm not allowed to use it cos I'm on a 111mm diet but I can gawp at it. (Check out the amazing German tongue-twister, "Funkenerosionsmaschinenen"!)
Thanks Ebay!
-
I read it as Funken-erosions-machine-nen.

Nice one!
-
It's the longest word I've ever seen on a SAK!
-
@Thunderpants said:
It's the longest word I've ever seen on a SAK!Especially awesome that they did it as an inlay... you could forgive them if they'd cheaped out and screen printed a word like that :)
-
@Thunderpants said:
It's the longest word I've ever seen on a SAK!That is some long word :o Thanks for sharing a pic of it

-
"(Check out the amazing German tongue-twister, "Funkenerosionsmaschinenen"!)"
Wow I'm an idiot. Pablo is right, I've stuck an extra syllable on the end.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
