MLCT Crony - Need your input!
-
Well the newest revision of the CAD design is almost done. Here's a quick rundown of whats going to be included:
-Alligator type wrench in one end, but it will be like an open end wrench instead of a closed end.
-A clasp will snap from one side of the open end to the other,for several reasons 1) It will serve as a way to attach and easily detach from a keychain 2) it will allow the wrench to be used as a box end wrench, which gives much more strength 3) if you cant get at somethign with a box end, you open the clasp, engage the nut, and close the clasp around it, allowing you to preform much more tasks that a box end would be able to handle 4) it will cover the included screwdriver
-The afformention screwdriver will be located at the wrench end of the tool. It will be made similar to leatherman micra's design of the philips screwdriver, for simplicity sake. I personally think that tool gets the job done, definately not as good as a real phillips driver, but it works. It will be located on one of the two "tongs" of the open ended wrench. The tong its located on will be about 1/8" or 1/4" longer then the other tong of the wrench to make sure the screwdriver can be used without the other tong bottoming out on the workpiece.
-There will also be a magnifying glass built into the tool. Its going to be very similar in size to the Victorinox glass magnifyers, so while it will be small, it will be functional and there if you need one. It will be in between the wrench and the prybar.
-The prybar will have the nail puller built in as well, which will be sharp enough to also work as a wire cutter. We are going to try and put a very small radius right before the prybar, to act as a fulcrum point when prying things
-There will be a bottle opener put in a different location than on the typical Atwoods
-Finally, there will be thumb grips put into the sides that will double as wire gagesI know it might be difficult to visualize, but you will all see the light once I post the CAD pictures!! Thanks for the interest and support guys, I'm really excited about moving forward with this.
-Dough
-
Wow!!! :o
That sounds mighty ambitious Dough! What will you use for a lens on the magnifying glass?
-
I'm going to try and find a cheap glass lens, just a simple double convex glass lens. What my plan is is to cut a hole the size of the lens about 3/4 through the sheet metal. Then insert the lens, and place a ring of metal with an OD equal to the lens, and an ID about 1/8" smaller than the OD on top of the lens. This will be made to proper thickness so everything will be completely flush. It will be tac welded and ground smooth.
-Dough
-
more power 2 ya there Dough

-
:)
-
oh man oh man,im soo intrested to se the results

-
Selfish plug....I'm going to be putting alot of time and some money into the development and production of a small run of these. If some people are interested, I might be able to sell some for a reasonable price. If you guys are gracious for the project, I could offer a slight additional discount for a recomendation in quaksters charge giveaway thread ::) >:D
lol. I was real interested in that charge, but unfortunately nobody knows me well enough to suggest me ;)-Dough
-
I might be convinced to know you better in the future should you send me each and every prototype. :D
-
u dont reply any pm´s man :o :o :o :o :o???? :D
-
What are you talkin about? I replied to you, and you replied back saying you were making a drawing...i'm still waitin on the drawing lol. Lookin forward to seeing your design.
-Dough
-
oh ok,i sent u lihnk to drawing i have screwed up the "send" then,sorry :-\

-
Sounds like an interesting project, I might want to pick one up when they're made. Any way to add a ruler in both metric and imperial?
-
Unfortunately I dont really have any way to print onto the metal or anything. I could, however, simply scribe in some measurements, such as a scale with 1/8" incriments on one side and some form of metric on the other.
-Dough
-
That would do, and should last longer. GL and can't wait for pic.
-
@DoughDTD said:
Unfortunately I dont really have any way to print onto the metal or anything. I could, however, simply scribe in some measurements, such as a scale with 1/8" incriments on one side and some form of metric on the other.-Dough
say,does the wrench fit 15mm nuts?if it does,its just awesome IMO for my needs atleast,maybe even for Mikes :D
-
I might be able to make it with a big enough wrench for 15mm, but that will be close to the maximum size that will work. Anything bigger than that would probably be useless in a tool this small anyway.
-Dough
-
yep,it doesnt have to be any larger i think,if id get a word for it.in my use,the 15mm wrench is very useful,and it does not have to be with great leverage either,just some few inches,to tighten and loose nuts of bicycles axle nuts.
i carry this one with just this task,its some 3,5 " long overall,if not even shorter.


-
A wire stripper can be useful as well.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

::)