New BO Swisstool
-
@LeaF said:
When I've got my SwiisTool BO (previous version - without crimper on pliers) I was seriously disapointed with a quality of coating.
Can anybody confirm that it's a normal situation?I recently got a Spirit S BO that was unused (advertised as such and none of the tools show any signs of wear), but the finish was in a similar condition. What's funny is how even with a black oxide finish, it's still sorta shiny; it has that almost oily sheen to it. My other BO SwissTools / Spirits have a similar appearance, but not to the same degree. As far as I know, it's just a byproduct of how they do things.
-
These are listed on Victorinox's USA site now: https://www.victorinox.com/us/en/Products/Swiss-Army-Knives/SwissTools/c/SAK_SwissTool
They're a bit more pricey than I expected, to be honest. I'm hoping places like SwissKnifeShop will get them down a bit, at least to $150 but lower would be nice. Might take a while since they tend to fetch fairly high prices on eBay right now. -
When I've got my SwiisTool BO (previous version - without crimper on pliers) I was seriously disapointed with a quality of coating.
Can anybody confirm that it's a normal situation?I recently got a Spirit S BO that was unused (advertised as such and none of the tools show any signs of wear), but the finish was in a similar condition. What's funny is how even with a black oxide finish, it's still sorta shiny; it has that almost oily sheen to it. My other BO SwissTools / Spirits have a similar appearance, but not to the same degree. As far as I know, it's just a byproduct of how they do things.
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.
-
When I've got my SwiisTool BO (previous version - without crimper on pliers) I was seriously disapointed with a quality of coating.
Can anybody confirm that it's a normal situation?I recently got a Spirit S BO that was unused (advertised as such and none of the tools show any signs of wear), but the finish was in a similar condition. What's funny is how even with a black oxide finish, it's still sorta shiny; it has that almost oily sheen to it. My other BO SwissTools / Spirits have a similar appearance, but not to the same degree. As far as I know, it's just a byproduct of how they do things.
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.
Cool, thanks for the info! Do you know how this compares with the black oxide coating the Leatherman uses? Actually, it would be cool if we had a general "coatings" thread about black oxide vs. burnished steel vs. Cerakote vs. TiNi — I'd start one, but I don't know anything, I just want to learn. :)
-
When I've got my SwiisTool BO (previous version - without crimper on pliers) I was seriously disapointed with a quality of coating.
Can anybody confirm that it's a normal situation?I recently got a Spirit S BO that was unused (advertised as such and none of the tools show any signs of wear), but the finish was in a similar condition. What's funny is how even with a black oxide finish, it's still sorta shiny; it has that almost oily sheen to it. My other BO SwissTools / Spirits have a similar appearance, but not to the same degree. As far as I know, it's just a byproduct of how they do things.
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.
Cool, thanks for the info! Do you know how this compares with the black oxide coating the Leatherman uses? Actually, it would be cool if we had a general "coatings" thread about black oxide vs. burnished steel vs. Cerakote vs. TiNi — I'd start one, but I don't know anything, I just want to learn. :)
Leatherman uses a black oxide powder process (according to their website). This I normally done using a copper-selenium powder and applied with a static charged spray gun. The advantage of the powder process over the hot solution process is, that you don't have to handle boiling, caustic liquids and still achieve a comparable corrosion resistance. The abrasion resistance is lower.
-
@italophil said:
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedlyNext time my wife tells me the oven is dirty, I'll just tell her it's brüniert...
-
Just curious, below picture identifies the Spirit XBS as 3.0224.3CCH. While Victorinox website listed it as 3.0224.3CN... So is there a difference?


-
@metasyntax said:
These are listed on Victorinox's USA site now: https://www.victorinox.com/us/en/Products/Swiss-Army-Knives/SwissTools/c/SAK_SwissTool
They're a bit more pricey than I expected, to be honest. I'm hoping places like SwissKnifeShop will get them down a bit, at least to $150 but lower would be nice. Might take a while since they tend to fetch fairly high prices on eBay right now.Haha, ya, I see they cost over 100% more with the coating. Problem is, Victorinox seems to be adopting the MAP ( min. advertised price) policy like Spyderco and a lot of others. So we may not see them any cheaper. :(
-
BO has been always overrated, I was lucky to get my BO Swisstool this year and it worns out fast, I don't carry my Spirit on a daily base because of this!
-
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.
[/quote]Spot on, italophil.

In reply #37, above, by jaya_man, the first ad says "Swisstool Burnished" and the second ad under "key features" says it is "burnished steel."
-
@Okie Shyster said:
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.Spot on, italophil.

In reply #37, above, by jaya_man, the first ad says "Swisstool Burnished" and the second ad under "key features" says it is "burnished steel."
[/quote]
In effect, it's just the same, right? -
@Okie Shyster said:
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.
Spot on, italophil.

In reply #37, above, by jaya_man, the first ad says "Swisstool Burnished" and the second ad under "key features" says it is "burnished steel."
In effect, it's just the same, right?
[/quote]I'm not sure I understand the question.
If you're asking whether "Swisstool Burnished" and "burnished steel" mean the same thing I'd say the answer is yes.
If you're asking whether burnished steel is the same as the BO process Leatherman uses, the answer is no.
Hope this helps.
-
Looks good but in the flesh so to speak

-
@Okie Shyster said:
@Okie Shyster said:
In German they call it "brüniert" which technically speaking is an oxide coating, but is more like burnished. It was traditionally made by applying linseed oil to a hot steel surface (>400C) repeatedly and was used for tooling and military applications. If they use that method it would explain the oily shine and the rubbing off.
Spot on, italophil.

In reply #37, above, by jaya_man, the first ad says "Swisstool Burnished" and the second ad under "key features" says it is "burnished steel."
In effect, it's just the same, right?
I'm not sure I understand the question.
If you're asking whether "Swisstool Burnished" and "burnished steel" mean the same thing I'd say the answer is yes.
If you're asking whether burnished steel is the same as the BO process Leatherman uses, the answer is no.
Hope this helps.
[/quote]
Thanks ... I meant the first one...
-
re:3.0224.3CCH & 3.0224.3CN:
I may be wrong, but I suspect that the 3.0224.3CCH is the black X model that was issued to the Swiss Army w/crimping device & green molle pouch.
The 3.0224.3CN is the exact same black X model with crimping device but w/nylon pouch. -
-
@marduk said:
re:3.0224.3CCH & 3.0224.3CN:
I may be wrong, but I suspect that the 3.0224.3CCH is the black X model that was issued to the Swiss Army w/crimping device & green molle pouch.
The 3.0224.3CN is the exact same black X model with crimping device but w/nylon pouch.Ahhh... certainly makes sense... CH for Switzerland...

-
Here's XC getting acquainted with XBS


-
Here's XC getting acquainted with XBS



Thanks

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
