Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sharpening with Paper Wheels

Scheduled Pinned Locked Moved Edged Tools
67 Posts 1 Posters 22.9k Views
  1. Home
  2. Tool Talk
  3. Edged Tools
  4. Sharpening with Paper Wheels
Sharpening with Paper Wheels
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • kwakster Offline
    kwakster
    Posts: 1,006
    kwakster Offline
    kwakster
    wrote on last edited by
    #31 Quote Reply

      Well, that depends on your point of view, :D

      Sharing info is what forums are all about, and useful tools with a great price to performance ratio like these Paper Wheels deserve to be introduced to a larger audience.

      1 Reply Last reply
      • kwakster Offline
        kwakster
        Posts: 1,006
        kwakster Offline
        kwakster
        wrote on last edited by
        #32 Quote Reply

          Did these chisel ground edges a a few years ago with a Paper Wheel coated with 15 micron diamond compound, and then stropped the burr on the other side off on hard leather with some 1 micron diamond compound.
          Both knives were quite blunt, one even more than the other.
          The knives are owned by two Dutch Special Forces guys who used & sharpened them while on tour in Afghanistan, and they wanted the new edges to have a little bling.

          1 Reply Last reply
          • kwakster Offline
            kwakster
            Posts: 1,006
            kwakster Offline
            kwakster
            wrote on last edited by
            #33 Quote Reply

              Below you see 3 different viewing angles of the edge i recently put on a brand new Sebenza 25 (which had a subpar factory edge)
              The owner of the knife took the pictures with a very expensive Leica camera to capture the different looks this edge type can have when seen from different angles.
              For obvious reasons i named this a bling & bite finish, and it performs very well on especially high (vanadium) carbide steels.

              I first reprofiled the factory edge from 35 degrees inclusive to 30 degrees inclusive with a Rubber Wheel coated with 230 grit diamond powder, then refined it with a Paper Wheel coated with 15 micron diamond compound, and lastly removed the tiny burr with a second Paper Wheel coated with 0.25 micron diamond compound.
              The new and ever so slightly convex edge could treetop the hair on the back of my hand (even whittle it a bit) and easily slice single ply toilet paper.
              And this was after i tested the edge with a few firm cuts into the edge of a piece of laminated desktop.

              1 Reply Last reply
              • kwakster Offline
                kwakster
                Posts: 1,006
                kwakster Offline
                kwakster
                wrote on last edited by
                #34 Quote Reply

                  This just came in, and it should be more than enough to coat both a Paper Wheel as well as a Rubber Wheel using the 3-step process.
                  According to my digital scale it weighs +/- 40 grams.

                  1 Reply Last reply
                  • Poncho65 Offline
                    Poncho65
                    Global Moderators
                    Posts: 88,523
                    Poncho65 Offline
                    Poncho65
                    Global Moderators
                    wrote on last edited by
                    #35 Quote Reply

                      Awesome Kwakster :cheers: Can't wait to see those results :o

                      :like:

                      1 Reply Last reply
                      • kwakster Offline
                        kwakster
                        Posts: 1,006
                        kwakster Offline
                        kwakster
                        wrote on last edited by
                        #36 Quote Reply

                          @ Poncho65: when i have some results with those Wheels i will post them here as well, :)

                          1 Reply Last reply
                          • kwakster Offline
                            kwakster
                            Posts: 1,006
                            kwakster Offline
                            kwakster
                            wrote on last edited by
                            #37 Quote Reply

                              I own several vintage Gerbers in M2 steel, both outdoor & kitchen models, and this Durendal slicer model from the '60's does duty in our kitchen.
                              Opening all kinds of paper & plastic food packages, slicing bags with espresso beans, cutting up larger fruits like melons & pineapples, slicing bread loafs and hamburger buns without crumbling, cutting sausages, etc.
                              Not every day, but at least several times a week.

                              I bought this Gerber about 2 years ago on E-Bay completely blunt, so i reprofiled & sharpened it with a SiC grit Paper Wheel, then refined the edge with 15 micron diamond compound on a second Paper Wheel, and then again with 6 micron diamond compound on a third Paper Wheel.
                              The tiny burr was removed with a fourth Paper Wheel coated with 0,25 micron diamond compound.
                              The idea was to get something of a semi-polish that would protect the exposed M2 edge better against corrosion issues during kitchen use, while still having some degree of bite.

                              The knife was then used for about 2 years in our kitchen, and when not in use stored on a magnet strip on our kitchen wall.
                              After those 2 years the edge only had a few very minor dings/flat spots in it (in the tiny belly area), but it could still shave the hair on the back of my hand on skin level quite well with about 90-95 % of the edge.
                              When cutting tomatoes however the edge tended to slide a bit over the skin before it started to cut.
                              The main reason for this kind of edgeholding is of course the fact that most of the edge on a slicer like this never touches a cutting board, only the belly area does, but the M2 steel performed quite admirably in my book.

                              A few weeks ago i resharpened the edge, this time only with 15 micron diamond compound, then deburred with 0,25 micron diamond compound, as i want to try the knife with some more bite.
                              Will have to find out if there will be corrosion issues or not.
                              So far i've only used it on food packaging (both paper & plastic, no fruit or other things yet), but here are a few pics how the knife & edge look now.
                              The edge feels sticky and is still treetopping sharp.

                              Specs:

                              Blade steel: hard chromed M2 steel
                              Hardness: 60-62 HRC
                              Handle material: cast on aluminum, chromed.
                              Overall length: 29,5 cm
                              Blade length: 16,5 cm
                              Blade thickness: 1,36 mm in front of the handle tapering to 0,84 mm close to the point
                              Thickness behind the edge: 0,5 mm
                              Edge angle: +/- 30 degrees inclusive, slightly convex

                              1 Reply Last reply
                              • kwakster Offline
                                kwakster
                                Posts: 1,006
                                kwakster Offline
                                kwakster
                                wrote on last edited by
                                #38 Quote Reply

                                  Did this user Spyderco PM2 in S30V steel for a customer who had seen pictures online of another PM2 in S110V steel i did earlier, and which are also somewhere in this thread.
                                  The man wanted the exact same full mirror edge he had seen on the other knife, it had to be 30 degrees inclusive, and it also had to have a guaranteed hair whittling sharpness.
                                  Of course i told him that this S30V is not the best steel for a full mirror edge, but it was what he wanted, :)

                                  The old edge had a few flat spots and a bit of a rounded point from use, but nothing serious.
                                  Total time i spent on this knife was one hour, in a succession of Paper Wheels with 15, 6, 3, and 1 micron diamond compound.
                                  As a comparison: the same full mirror edge on that PM2 in S110V steel the man saw online took me two hours.
                                  Most of this time is going into the many visual checks i do in between with my Victorinox loupe under bright light, not into the actual sharpening.

                                  These are the quick pics i also sent to the customer, and they can be clicked twice for a bit more detail.
                                  The owner was satisfied btw.

                                  1 Reply Last reply
                                  • Poncho65 Offline
                                    Poncho65
                                    Global Moderators
                                    Posts: 88,523
                                    Poncho65 Offline
                                    Poncho65
                                    Global Moderators
                                    wrote on last edited by
                                    #39 Quote Reply

                                      Those are some very nice and shiny edges Kwakster :o :like: :like: :like:

                                      1 Reply Last reply
                                      • kwakster Offline
                                        kwakster
                                        Posts: 1,006
                                        kwakster Offline
                                        kwakster
                                        wrote on last edited by
                                        #40 Quote Reply

                                          Hinderer XM-18 Slicer grind in S35VN steel.
                                          According to my Tormek angle gauge the factory edge angle measured between 45 and 50 degrees inclusive, while the thickness of the steel just behind that edge went from 0.7 mm at the heel to 0.6 mm at the tip.
                                          The knife is going to be used as a hunting folder, and the owner had 2 wishes: if possible no visually wide bevels, plus he wanted to be able to maintain the new edge on a Spyderco Sharpmaker.

                                          Before sharpening:

                                          After sharpening.

                                          Edge reprofiled to an almost exact 35 degrees inclusive with a Paper Wheel coated with 220 grit SiC, after which the burr was removed with a second Paper Wheel coated with 0.25 micron diamond compound.
                                          The new edge is what i would call sticky sharp.

                                          1 Reply Last reply
                                          • kwakster Offline
                                            kwakster
                                            Posts: 1,006
                                            kwakster Offline
                                            kwakster
                                            wrote on last edited by
                                            #41 Quote Reply

                                              This special version of the Spyderco Paramilitary 2 in CPM-M4 steel & carbon fiber is in use with a Dutch knife forum member.
                                              A small fraction of the tip had broken off and the apex sustained some damage (see pic 3)
                                              This is how the knife looked before sharpening.
                                              You can click 2 X on each pic for more detail.

                                              After sharpening.
                                              First i ground the old apex flat on the Tormek Blackstone until all damage in the apex was gone & there was a new point.
                                              Then i made a new edge with 15 micron diamond compound on a Paper Wheel, which was then refined with 6, 3, and 1 micron diamond compound on dedicated Paper Wheels to a full mirror.
                                              The new edge measures 30 degrees inclusive and is hairwhittling sharp.
                                              You can click 2 X on each pic for more detail.

                                              1 Reply Last reply
                                              • zoidberg Offline
                                                zoidberg
                                                Posts: 38,161
                                                zoidberg Offline
                                                zoidberg
                                                wrote on last edited by
                                                #42 Quote Reply

                                                  :like: :like: :like:

                                                  1 Reply Last reply
                                                  • SteveC Offline
                                                    SteveC
                                                    Global Moderators
                                                    Posts: 73,535
                                                    SteveC Offline
                                                    SteveC
                                                    Global Moderators
                                                    wrote on last edited by
                                                    #43 Quote Reply

                                                      Ditto ^

                                                      1 Reply Last reply
                                                      • ducttapetech Offline
                                                        ducttapetech
                                                        Posts: 18,707
                                                        ducttapetech Offline
                                                        ducttapetech
                                                        wrote on last edited by
                                                        #44 Quote Reply

                                                          Nice!

                                                          1 Reply Last reply
                                                          • kwakster Offline
                                                            kwakster
                                                            Posts: 1,006
                                                            kwakster Offline
                                                            kwakster
                                                            wrote on last edited by
                                                            #45 Quote Reply

                                                              Dustar Model 1 Arad '67 Commemorative combat knife from a collector.
                                                              The factory "edge" was very rough and also still had a burr so thick that i could lift the entire knife from the table by hooking it with my finger nail.
                                                              Edge angle was +/- 45 degrees inclusive which i left intact as the customer did not want wider bevels.
                                                              After grinding the apex flat on the Tormek Blackstone the edge was resharpened on a Paper Wheel with 15 micron diamond compound then deburred with a second Paper Wheel with 3 micron diamond compound, an the new edge can just treetop the hairs on the back of my hand.
                                                              Probably the most wear resistant D2 steel i have sharpened so far.

                                                              1 Reply Last reply
                                                              • Sparky415 Offline
                                                                Sparky415
                                                                Posts: 13,000
                                                                Sparky415 Offline
                                                                Sparky415
                                                                wrote on last edited by
                                                                #46 Quote Reply

                                                                  Great pictures K :tu:
                                                                  Looks perfect from where I'm sitting :salute:

                                                                  :cheers:

                                                                  1 Reply Last reply
                                                                  • kwakster Offline
                                                                    kwakster
                                                                    Posts: 1,006
                                                                    kwakster Offline
                                                                    kwakster
                                                                    wrote on last edited by
                                                                    #47 Quote Reply

                                                                      This vintage Al Mar Applegate Fairbairn dagger from a display collection had factory edges which were rather coarse, had a few flat spots, and a flattened point.
                                                                      Since the "R" from Rex Applegate's signature was already quite close to the +/- 50 degrees inclusive factory edge i chose not to reprofile but instead just polish the existing bevels a bit with successively 15.0 micron, 3.0 micron, and 1.0 micron diamond compound on dedicated Paper Wheels.
                                                                      Both new edges can shave the hair on the back of my hand on skin level.
                                                                      ( click each pic 2 x for a bit more detail)

                                                                      1 Reply Last reply
                                                                      • Sparky415 Offline
                                                                        Sparky415
                                                                        Posts: 13,000
                                                                        Sparky415 Offline
                                                                        Sparky415
                                                                        wrote on last edited by
                                                                        #48 Quote Reply

                                                                          @Sparky415 said:
                                                                          Great pictures K :tu:
                                                                          Looks perfect from where I'm sitting :salute:

                                                                          :cheers:

                                                                          This again :salute:

                                                                          Is it rude to quote myself? :think:

                                                                          1 Reply Last reply
                                                                          • kwakster Offline
                                                                            kwakster
                                                                            Posts: 1,006
                                                                            kwakster Offline
                                                                            kwakster
                                                                            wrote on last edited by
                                                                            #49 Quote Reply

                                                                              Absolutely not, and thanks, :D

                                                                              1 Reply Last reply
                                                                              • Sparky415 Offline
                                                                                Sparky415
                                                                                Posts: 13,000
                                                                                Sparky415 Offline
                                                                                Sparky415
                                                                                wrote on last edited by
                                                                                #50 Quote Reply

                                                                                  Thank you K, :salute:
                                                                                  Always interesting stuff and stunning pictures :tu:

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Edged Tools
                                                                                  4. Sharpening with Paper Wheels
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0