Cap lifter on an Executive
-
Was it August last time I worked on this project? I've been lazy I guess. But since we're coming up on Christmas and it's meant to be a Christmas gift I guess it's time to get started.
I have acquired the necessary materials. Brass sheet, brass rod, brass flat stock (for the spacer) and some Ebony.

I decided to start small with the spacer so I cut a small piece of the flat bar (plenty of extra to hold on to while working) and drilled a 2mm hole (no need to be exact, there will be plenty of shaping to do anyway).

Deburring, it would be awesome if I could use the Dremel for more of the work but since I live in a fairly small apartment I have to consider dust management carefully. I have considered building a removable glovebox/hood for my work surface but nothing has come of it as of yet.

Next I found myself a M2 machine screw from my tin of screws and a matching nut.


After placing the parts in my vice I can now use the original part as template.

Coarse cutting.

And coarse filing.

And needle file for the last work.

When the side is done it's time to go on to the next side, basically going through the same steps again.

And this is where I left of for today, it's going to take some time but hopefully that will pay of in result. There are quite a few pictures now so it would be nice if a Moderator would be so kind as to add a warning in the topic title for those with limited bandwidth.
-
Really great pics and close-up shots 42
I can't wait to see this project finished :o

-
Been doing some more work but before I continue and before I put up pictures, am I gonna hit myself for not reaming the holes? Right now I'm using standard drill bits and the holes have a faint but unmistakable triangular shape to them.
-
So, more pictures today, this is not a quick job the way I'm doing it. I would say that I have fairly good tools but I'm lacking in workspace.
First step was to attach the liners together so that I could shape them all at the same time and after that I did some coarse shaping with my Dremel (Proxxon). I so wish I had had a belt-sander for this, as it where it took ages and I had to work more or less inside my dustbin to catch most of the brass dust.


After this I did some deburring and then did some finer work with sandpaper, ending in something fairly smooth and of the right size.

The ebony I was planning on using had to go since the blade had wobbled all over the place when I cut it previously (on a table saw)

Instead this mystery wood had to do, I was planning on using it for a knife of my own but I can cut more from the ashtray that it came from. I marked out where the tweezers were going and started carving. The chisel is made from some unknown broken tool that my father had laying around. It's just a bit broader than the 3 mm that the T&T are.

After making a rough carving I sawed out the slot and then started the fitting. Don't worry, I sanded the piece so that those ugly scratches wouldn't show.


Here I held the liner to the scale to see how well the tweezers would fit. Not very well it seems so I marked where it stopped and did some carving on the inside there.

Now that's better!

Lastly I epoxied the scale to the liner.

-
Excellent looking work so far

-
Did some more work today, glued the next scale to the liner, I don't plan on having the toothpick (I would like this one to have no plastic at all) so it was very straight forward.
I did the shaping for the first scale, it seems that the tweezers slot didn't come out as centred as I would have liked but it's not to bad either (it doesn't look as bad as in the picture!).

I drilled the holes through the scale I plan on this one having exposed rivets. I should have done this before gluing so I could have lined it up properly. Before I have used a scale as template by drilling through it at the relevant places, I don't know why I didn't do that this time, live and learn I guess.

It's coming along fairly well, all the pieces are started and I should be able to make my morning of 22nd deadline.

-
So when I started today I had all the pieces but at a very basic level. So now it was time to get everything where I wanted it. I started by doing the rough shaping of the second scale with my Dremel, followed by sticking the two scales together with my pins and sanding the sides to where I wanted them.

After that I finished the middle liner. I had left it yesterday after cutting the basic shape out with a jewellers saw but now I used first the Dremel followed by needle files and lastly 600 grit sandpaper to finish it. While working on it I clamped it in my vice after putting electrician's tape on the jaws.


Next up I counter-sunk the pin holes. I messed this step up a bit and made it to deep on one hole and then I overcompensated on the rest of the holes.

Then came the single step that did the most for the look of progress, assembly! For this I made use of my Spirit after covering the pliers in tape so as not to mar anything.

I then started the peening work, the overly countersunk hole is clearly visible at the lover right pin here.

When I had done some basic peening, enough that I felt sure it wouldn't just move through I cut of the extra length of pin.

Peening both sides was a bit of a hassle on the super small "anvil" so I resorted to making a harness. I didn't as such hold the knife in place but at least I didn't have to keep it from tipping off.

Finally I built myself a tool for the last operation, rounding the edges. It started it's life as a stick, a short piece of double sided tape (the foamy kind) and two different grits of sandpaper (180 and 600).

The brass head on the tweezers had a bubble in the casting so I elected not to throw any more work after a piece that is going to be replaced, other than that the knife is finished. I opted for some rapeseed (canola) oil as finish, since it is both food safe and not overly prone to go rancid.


-
Great work and work in progress pictures

I like to see how other people work!

Inside I run my house hoover with the nozzle 'behind' the work when using the dremel (but you have to be careful with small parts
) a bit noisy but keeps the dust down ;)
-
Lovely stuff there

-
I have to say, that looks pretty great
-
Nice work man

-
Thanks guys! I'm pretty happy with how it turned out, it's not perfect but it does look nice and there's nothing stopping me from making a few tweaks later on. I'm hoping to do a bit of a write up and collect my thoughts on what worked and what didn't as well as what tools were necessary or useful.
-
GJ. I'm sure she will be thrilled to have it

-Tom
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
