Crescent Toolzall Electrician Pro
-
Your tool is so different from mine!
I have the same model, Bear & Son branded.
I don't have the unlocking tool tabs.
Also, I have the combo edge blade, but I also have a serrated sheepsfoot instead of the saw. I want a saw!
And, even after sending it in to get it worked on, my pliers head is still really loose. They might have ground down the screw that kept it from fully closing, but they didn't tighten it.
Sigh. I really wanted to love this tool.
-
Nice job. Does that tool come with a Crimper? If so I think it is a great little design and a great tool!
-
Interesting tool that. :)
Thanks for the review.

-
@gafftapegreenia said:
Your tool is so different from mine!I have the same model, Bear & Son branded.
I don't have the unlocking tool tabs.
Also, I have the combo edge blade, but I also have a serrated sheepsfoot instead of the saw. I want a saw!
And, even after sending it in to get it worked on, my pliers head is still really loose. They might have ground down the screw that kept it from fully closing, but they didn't tighten it.
Sigh. I really wanted to love this tool.
So do the tools lock or not? Yeah the saw is one of the better tools in it :-\ Sorry to say I haven't used it enough to tell if the head is gonna become loose in time if it does I'll let you know

-
@hawkchucker said:
Nice job. Does that tool come with a Crimper? If so I think it is a great little design and a great tool!Sorry to say unless it is a poorly cast one in the plier head similar to the Super Tool's I can't really tell. I suppose you could use it as a crimper though, but it being an electrician tool they should have incorporated one :-. Other than that it is a great tool

-
Nice one Ponch
:D -
Another fine write up Poncho! 8)
I too would like to see this type of plier head used on more multitools. Maybe a more modern version of it would be better. The Electrician Bear Jaws is still listed on their site, but it has been around for a long while.
-
Excellent review. Poncho!
-
I have the earlier version of that tool the PST type one. Also does your wire strippers have a lot of play? Mine have a lot compared to my Radio Shack Leatherman.
-
Nice tool, I have the exact same one. Re-wired my garage with this and it was a solid performer.
I didn't like how the release tabs protruded from the closed tool so I filed them down at the point where they contact the lock and now they sit flush with the handles.
Apparently Cresent made another version of this which included a robertson (square drive) screwdriver. I tried locating one but couldn't find any.great review.
-
Welcome to the forum mate :)
-
@Micky d said:
Welcome to the forum mate :)What he said :D Welcome

-
Welcome.

-
Thanks guys - glad to be onboard.
-
@Nutznboltz said:
Nice tool, I have the exact same one. Re-wired my garage with this and it was a solid performer.
I didn't like how the release tabs protruded from the closed tool so I filed them down at the point where they contact the lock and now they sit flush with the handles.
Apparently Cresent made another version of this which included a robertson (square drive) screwdriver. I tried locating one but couldn't find any.great review.
Was it as adequate of a wire stripper as a dedicated pair? if you don't mind me asking :) also did you happen to use the wire bender holes on the head as they say to on the back of the packaging?
-
Nice tool, I have the exact same one. Re-wired my garage with this and it was a solid performer.
I didn't like how the release tabs protruded from the closed tool so I filed them down at the point where they contact the lock and now they sit flush with the handles.
Apparently Cresent made another version of this which included a robertson (square drive) screwdriver. I tried locating one but couldn't find any.great review.
Was it as adequate of a wire stripper as a dedicated pair? if you don't mind me asking :) also did you happen to use the wire bender holes on the head as they say to on the back of the packaging?
For general electrical work - wire stripping/ wire bending it is excellent. the electrician head is as good as any proffesional models I've used. I did not use the holes for bending wire, I prefered using the small needle nose pliers on the tip of the head. For bending or looping the wire for the terminal screws it works much easier, though I'm sure the holes would work just as well. I like this tool alot although I think a serrated sheepsfoot blade would've been more useful for electrical work and not sure why there's a saw, a crimper would've been nice.
-
@Nutznboltz said:
I think a serrated sheepsfoot blade would've been more useful for electrical work and not sure why there's a saw, a crimper would've been nice.I agree 100% about the sheepsfoot blade and crimper. A sheepsfoot blade seems like a no-brainer for anyone who's done electrical work. Saws can be useful for drywall and such.
-
Don't believe a crimper could be added but the rest of the tools do swap out with LM (old school LM that is) I put a PSTII diamond file on my Maintenance Pro (the shears version) and it swapped out pretty good. One might take the serrated sheep foot blade of a LM Crunch and put it in there (but who would want to take a Crunch apart :ahhh )

Plus I don't have a Crunch they may have a totally different end on them :-\
-
Does anyone on here have a Crunch I don't think I have ever heard anyone post about using one?
-
@american lockpicker said:
Does anyone on here have a Crunch I don't think I have ever heard anyone post about using one?There was a Crunch Craze a while back where either folks were saying how great they were, and other folks were willing to give their left arm for one :D
I've got one and EDC it sometimes, it's a great tool and still fetches a high price on ebay..
And back on topic kinda, why a serrated sheepsfoot for electrical work? I'm thinking for slicing heavy sheathing around a wire..?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login