Amorphous April Multi-Plier Challenge - JOIN NOW !
-
@Poncho65 said:
That bit adapter adds a lot of versatility to any square bit phillips MT
I have already used it on mine this week and it performed wonderfully

Now, I need to replace that nasty Wharncliffe blade and I'd be much happier. Though, to be honest, I really don't expect the Gerber to ever replace my load of Leathermans, I can see the appeal to some folks.
Sent from my Nexus 6 using Tapatalk
-
I think I need to oil mine so I can flick it out better
That part is fun :D -
@Poncho65 said:
I think I need to oil mine so I can flick it out better
That part is fun :DThe unit I sent in to Gerber to fix that nasty blade...

...it flicked easily.They chose to send me a brand new Pro Scout with the Wharncliffe blade (which I hate....But they were very gracious to send the new tool!!)
I have been setting here watching TV and flicking the tool out over and over. It's getting better!
We are getting ready for a quick trip (about 3 hours or so...) to Nashville, TN for dinner and to hang out. The Gerber will be with me the entire time.
Sent from my Nexus 6 using Tapatalk
-
If the blade and scissor is swapped around on the Pro Scout then the nail nick on blade is accessible.
I have put scissors in the opposit position on my mp600 for this challenge (see the earlier photo). This makes the scissors nail nick point inward but the scissors are still pretty easy to get out IMO.The remgrit saw holder cannot be placed in the opposite position... I just tried swapping the blade and the saw holder

Standard position on the Pro Scout

Peeled apart

Swapped around

BUT the saw holder blocks the sliding plier head


Its a very little difference but enough to block the pliersSo dont do this swap :D ... but a swap between the scissors and blade should expose the nail nick on the blade (and hide it on scissors) as already noted.
I have not done this with the full set of pro scout tools so maybe I missed a potential issue.Edit: The blocking issue could be solved by putting in extra spacers to align the saw holder properly (?). I will try it at some point.
-
Day 7 at tech rehearsal.

-
Day 7 - TGIF
-
I think I need to oil mine so I can flick it out better
That part is fun :DThe unit I sent in to Gerber to fix that nasty blade...

...it flicked easily.They chose to send me a brand new Pro Scout with the Wharncliffe blade (which I hate....But they were very gracious to send the new tool!!)
I have been setting here watching TV and flicking the tool out over and over. It's getting better!
We are getting ready for a quick trip (about 3 hours or so...) to Nashville, TN for dinner and to hang out. The Gerber will be with me the entire time.
Sent from my Nexus 6 using Tapatalk
I was in Nashville today as I am every work day ::) :D Have a great time

-
Another awesome day guys
We are already one week into this challenge :o I am getting more use to this MT and I am sure by the end of the month I will have a new appreciation for Gerbers
I have been on ebay already looking to grab a different model on the cheap so I can try something else of there out sometime
:D -
I think I need to oil mine so I can flick it out better
That part is fun :DThe unit I sent in to Gerber to fix that nasty blade...

...it flicked easily.They chose to send me a brand new Pro Scout with the Wharncliffe blade (which I hate....But they were very gracious to send the new tool!!)
I have been setting here watching TV and flicking the tool out over and over. It's getting better!
We are getting ready for a quick trip (about 3 hours or so...) to Nashville, TN for dinner and to hang out. The Gerber will be with me the entire time.
Sent from my Nexus 6 using Tapatalk
I was in Nashville today as I am every work day ::) :D Have a great time

Just got here. At La Quinta Inn just off I 65 exit 97...
Had to gulp some coffee drinks to make the drive...I hate driving! Haha!

Sent from my Nexus 6 using Tapatalk
-
-
Day 8
Very early morning for me. Here's Mr. Pinchy amidst the thorns of a Bougainvillea, and reaching for the moon.
-
8

-
would've been easier -albeit less fun- with the Spyderco, but what the heck are challenges for? :ahhh


-
Already some awesome stuff today peeps :o

Zrxoa1 be careful down here in the Guitar, traffic is always a madhouse :D If you happen to come down West End I am working on it and 23rd til around 1:30

Have fun

-
Day 8 of 30
Here is a pic of my sheath and bit kit

20170408_072005 by Poncho 65, on FlickrAnd a beauty shot
It is bein sneaky :o :D
20170407_172022 by Poncho 65, on Flickr -
Great shots guys

Peacent, I like your approach using the mp600 for cutting food instead of a better knife. Totally what I would do :DDay 8
Messing around with the tool layout. Had all tools out to see if something could be improved :ahhh

The saw and scissors were swapped around but this interfered again with the sliding plier head
... it was swapped back

All in all, the flat heads were grouped together so the awl is no longer amongst them :'( ... and has been excluded to the other handle. Not much difference but it makes more sense :D

-
Day 8 - Assisted me with my weapon maintenance today at drill
-
Day 8 I was playing with my MP600 and noticied that the nail nick on the knife doesn't line up with the cutout.


-
Day 8...
Not much here, just laying on the counter here in the hotel room...

Sent from my Nexus 6 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
