Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Backsprings in motion

Scheduled Pinned Locked Moved Swiss Army Knights Forum
28 Posts 1 Posters 6.4k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Backsprings in motion
Backsprings in motion
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • knife-man Offline
    knife-man
    Posts: 96
    knife-man Offline
    knife-man
    wrote on last edited by
    #20 Quote Reply

      if we could convince someone to bend one out and take a look at the surface finish on the inside I could tell .. EDM leave like a sandblasted finish. I doubt the inside of the slot's are polished in anyway after machining

      1 Reply Last reply
      • J-sews Offline
        J-sews
        Admin Team
        Posts: 23,224
        J-sews Offline
        J-sews
        Admin Team
        wrote on last edited by
        #21 Quote Reply

          @knife-man said:
          if we could convince someone to bend one out and take a look at the surface finish on the inside I could tell .. EDM leave like a sandblasted finish. I doubt the inside of the slot's are polished in anyway after machining

          You mean the surface finish in <u>between</u> the fingers, right?

          1 Reply Last reply
          • knife-man Offline
            knife-man
            Posts: 96
            knife-man Offline
            knife-man
            wrote on last edited by
            #22 Quote Reply

              yeah ... I know what I mean even if no-one else does most of the time :-\

              1 Reply Last reply
              • J-sews Offline
                J-sews
                Admin Team
                Posts: 23,224
                J-sews Offline
                J-sews
                Admin Team
                wrote on last edited by J-sews
                #23 Quote Reply

                  I'm holding onto the backspring fingers piece from my disassembled Spirit right now.  (Don't ask!  :angry:)  Anyhow, a piece of ordinary typing paper will barely  fit between the fingers. Checked with a micrometer, the paper measures .0035" thick, or less than .1mm.

                  I was told once that a wire EDM can only make cuts down to .2mm wide. How the heck does Vic cut those fingers?

                  edit: I forgot the decimal point in front of the 1mm and 2mm specs. Added 5-15-07.

                  1 Reply Last reply
                  • Tom Munch Offline
                    Tom Munch
                    Posts: 1,384
                    Tom Munch Offline
                    Tom Munch
                    wrote on last edited by
                    #24 Quote Reply

                      Maybe they use water jets or something?

                      Tom

                      1 Reply Last reply
                      • J-sews Offline
                        J-sews
                        Admin Team
                        Posts: 23,224
                        J-sews Offline
                        J-sews
                        Admin Team
                        wrote on last edited by
                        #25 Quote Reply

                          @Tom Munch said:
                          Maybe they use water jets or something?

                          Tom

                          The place across the road from our shop has an abrasive water jet cutter. The width of cut is about .040" (1mm) or about ten times as wide as the Victorinox cuts. Must be done some other way.

                          1 Reply Last reply
                          • knife-man Offline
                            knife-man
                            Posts: 96
                            knife-man Offline
                            knife-man
                            wrote on last edited by
                            #26 Quote Reply

                              EDM can take .1mm cut's I think its's the smallest wire size available ATM.

                              and as .0035" is only just a smidgen under .1mm I would still suspect EDM If I had one I could check it with my shim's for a propper size check (presuming I could find them and that they arnt too rusty) .. Paper inst the best material for use as a Shim ::). But I cent afford to buy one.

                              1 Reply Last reply
                              • J-sews Offline
                                J-sews
                                Admin Team
                                Posts: 23,224
                                J-sews Offline
                                J-sews
                                Admin Team
                                wrote on last edited by
                                #27 Quote Reply

                                  @knife-man said:
                                  EDM can take .1mm cut's I think its's the smallest wire size available ATM....

                                  Then you are probably correct about how the slits are cut.

                                  Another good thing about cutting with a wire EDM (electrical discharge machine) is that it leaves no burrs or bulges in the metal, like a thin slitting saw or bandsaw would do.

                                  1 Reply Last reply

                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                  With your input, this post could be even better 💗

                                  Register Login

                                  1. Home
                                  2. Tool Talk
                                  3. Swiss Army Knights Forum
                                  4. Backsprings in motion
                                  Reply
                                  • Reply as topic
                                  Log in to reply
                                  COMMUNITY LINKS
                                  EDC-TV SAKWiki GearFeed SAKSelector
                                  Operational Funds

                                  Help us keep the Unworkable working!

                                  Make A Donation
                                  November Goal: $300.00
                                  Due Date: Nov 30
                                  Total Receipts: $0.00
                                  Below Goal: $300.00
                                  0% funded
                                  • Login

                                  • Don't have an account? Register

                                  • Login or register to search.
                                  • First post
                                    Last post
                                  0