CyberTool owners thread
-
@Mactire404 said:
Aaand another club I can join!I've bought a Sapphire scaled CT29 on sale just for the heck of it.
When I had to send in my Handyman for warranty I carried the CT29 for a short while.
I missed my Handyman so much I didn't send it in but that's another story.I messed up the tweezers when I bent them to make a tension wrench i norder to pick my doorlock. We managed to lock outselves out.
In the end the rusty hairpin I found wasn't sturdy enough to pick the lock. I disassembled the window (which was cracked open) with the CT29.
Also the small hex bits work wonders on the machines at work. Saves me a call to IT every now and then.However, I missed the pliers and scissors in my Handyman. So I tracked down a second hand CT34. Apart from the butchered scales it's in good condition. I still need to get new scales, but I'm low on funds right now :-[.
In retrospect getting a CT34 was kind a stupid. I carry Handyman anyway, so I always have scissors and pliers at hand. I already missed the chisel on the CT34 once. So now the CT34 rides in my backpack, I use the bits regularly.
I'll post picks later. ;)I can sympathize with the 20/20 hindsight regret. I set out to get a new in box CT-34 and a used excellent CT-34. The new CT-34 that I purchased did not have a box and the used in excellent condition CT-34 had a company logo. I was initially so glad to have a CT-34 that I jumped on a great deal for another used in excellent condition CT-34 with a Leica logo. Now, I wish that I had only picked up a single CT-34. All three CT-34s have ruby scales. I purchased sapphire scales to replace one of the logo scales and I will probably sell the other logo scale CT-34. If I had it to do over again, I would get a CT-29, CT-34 & CT-41 and skip the CT Lite and multiple copies.
Well, we live and learn.
-
@NorCalJim said:
I can sympathize with the 20/20 hindsight regret......Well, we live and learn.
Exactly, live and learn.
I also jumped at what I thought was a nice offer. I actually got a couple of SAKs back then. But the Traveller I got didn't have the right backscales unfortunately. I still have to contact Victorinox about this, I really want the propers cales in place, but I can't get them anywhere.
And as mentioned, the scales of CT34 need replacing.
Both knives were very dirty and needed a very good scrub to get them in perfect working order. Luckily, all tools are in pristine condition.Moral of the story is to think twice before you jump on an offer. We can only spend our money once!
-
Probably posted before but I'll bump the thread...
My 125th Anniversary Jubilee Series Cybertool

-
Handing in my notice. No longer a member of the CT owners club


-
@glenfiddich1983 said:
Handing in my notice. No longer a member of the CT owners club

Aww, did you drop it? They don't make them like they used to do they

-
Handing in my notice. No longer a member of the CT owners club


Aww, did you drop it? They don't make them like they used to do they

No they don't. After the CyberTool fell apart I dropped three more SAKs, just as a test. And guess what happened?

-
Wow and the scales and brass parts just disappeared?
Another thread taken over by the Dutch :D
-
I have a CT34 that I use all the time and has a interesting story behind it. Also have a CT41 thats NIB I may sell but Im not sure yet.

-
@glenfiddich1983 said:
No they don't. After the CyberTool fell apart I dropped three more SAKs, just as a test. And guess what happened?
That's it. I'm selling my SAKs and order my new ones via AliExpress!
@captain spaulding said:
I have a CT34 that I use all the time and has a interesting story behind it. Also have a CT41 thats NIB I may sell but Im not sure yet.
You can't make mention of an interesting story and not tell it! So spill it mister!

-
No they don't. After the CyberTool fell apart I dropped three more SAKs, just as a test. And guess what happened?

That's it. I'm selling my SAKs and order my new ones via AliExpress!
@captain spaulding said:
I have a CT34 that I use all the time and has a interesting story behind it. Also have a CT41 thats NIB I may sell but Im not sure yet.
You can't make mention of an interesting story and not tell it! So spill it mister!

Well, one day I listed a Juice CS4 for trade on the forum and one of our members showed interest. We decided to do a trade and when we exchanged addresses we found we lived in the same city. Obviously we just decided to meet up locally the next day. We decided to meet about 5 minutes away from my house. As I was getting ready to leave I noticed the neighbor across the street leaving his house as well. We both headed in the same direction and made our way down to the meeting spot. Funny thing is it turns out my neighbor across the street from me was the person I was meeting. We made the trade, had a laugh, and became friends. We used to show each other new tools, lights, whatever. He is the reason I got into Zebralights. We both ended up moving and he does not check the forums much anymore, but every time I use that CT34 I think about that day.

Funny thing is I am meeting another member today that lives one city over. We have met for a deal before though.
-
Wow and the scales and brass parts just disappeared?
Another thread taken over by the Dutch :D
Maybe the brass parts were never there in the first place, it would explain a lot!
:P
BTW that's a nice story Captain!
-
@captain spaulding said:
Well, one day...Spoiler:
I listed a Juice CS4 for trade on the forum and one of our members showed interest. We decided to do a trade and when we exchanged addresses we found we lived in the same city. Obviously we just decided to meet up locally the next day. We decided to meet about 5 minutes away from my house. As I was getting ready to leave I noticed the neighbor across the street leaving his house as well. We both headed in the same direction and made our way down to the meeting spot. Funny thing is it turns out my neighbor across the street from me was the person I was meeting. We made the trade, had a laugh, and became friends. We used to show each other new tools, lights, whatever. He is the reason I got into Zebralights. We both ended up moving and he does not check the forums much anymore, but every time I use that CT34 I think about that day.
Funny thing is I am meeting another member today that lives one city over. We have met for a deal before though.
Well, that is an interesting story indeed! Thanks for sharing!

-
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
-
@GoatDragon said:
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
I don't know about the Cybertool bits, but around here, 4/5 of the cross screws are pozidrive, not philips. >:(
And Victorinox doesn't make an inline pozidrive driver of the same type as the inline philips driver.
So I had to cut a slot in a 1/4 pozidrive bit to make it fit on the bottle opener, so that my SAK can actually deal with the most common cross screw around here. :ahhh -
@GoatDragon said:
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
It will work, but the fit won't be 100% so this will wear out the screw, bit or both faster.
So yes, they will serve you less.
You can also buy a new bit (usualy around €4 here) that is a Philips. -
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
It will work, but the fit won't be 100% so this will wear out the screw, bit or both faster.
So yes, they will serve you less.
You can also buy a new bit (usualy around €4 here) that is a Philips.That's what I suspected, darn.
The only bits I can find for sale on Amazon or eBay are the same four that come with the Cybertool. The closest I can find is this "positive bit" phillips, which sounds like someone making a listing who doesn't have any clue that posidrive is actually a word. The picture of the product does look like a normal phillips to me, however. That being said, I don't know if I have ever seen a posidrive screw or screwdriver/bit in person before so I am hardly an expert on telling them apart.
Any idea where I can buy the normal phillips bit you speak of?
-
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
It will work, but the fit won't be 100% so this will wear out the screw, bit or both faster.
So yes, they will serve you less.
You can also buy a new bit (usualy around €4 here) that is a Philips.That's what I suspected, darn.
The only bits I can find for sale on Amazon or eBay are the same four that come with the Cybertool. The closest I can find is this "positive bit" phillips, which sounds like someone making a listing who doesn't have any clue that posidrive is actually a word. The picture of the product does look like a normal phillips to me, however. That being said, I don't know if I have ever seen a posidrive screw or screwdriver/bit in person before so I am hardly an expert on telling them apart.
Any idea where I can buy the normal phillips bit you speak of?
I was in a store during my vacation 2 weeks ago which had an INSANE stock and he had all bits available.
No such luck with my local retailer but you might want to check yours.Posidriv screws became more common then regular Philips here troughout the years.
-
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
It will work, but the fit won't be 100% so this will wear out the screw, bit or both faster.
So yes, they will serve you less.
You can also buy a new bit (usualy around €4 here) that is a Philips.That's what I suspected, darn.
The only bits I can find for sale on Amazon or eBay are the same four that come with the Cybertool. The closest I can find is this "positive bit" phillips, which sounds like someone making a listing who doesn't have any clue that posidrive is actually a word. The picture of the product does look like a normal phillips to me, however. That being said, I don't know if I have ever seen a posidrive screw or screwdriver/bit in person before so I am hardly an expert on telling them apart.
Any idea where I can buy the normal phillips bit you speak of?
I was in a store during my vacation 2 weeks ago which had an INSANE stock and he had all bits available.
No such luck with my local retailer but you might want to check yours.Posidriv screws became more common then regular Philips here troughout the years.
Unfortunatly, Victorinox retail stores are hard to come by here in America. I checked google maps for them recently, and the only one that had existed in my entire state was marked as permanently closed. Gotta be online for order for me.
-
[quote author=GoatDragon link=topic=50953.msg1538481#msg1538481 date=1502863431]
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would? I rarely encounter Pozidrive screws (had to look them up to even see what they were), so would Pozidrive drivers on a Cybertool be less useful to me because of that? Are there any advantages to having Pozidrive drivers over normal ones?
It will work, but the fit won't be 100% so this will wear out the screw, bit or both faster.
So yes, they will serve you less.
You can also buy a new bit (usualy around €4 here) that is a Philips.That's what I suspected, darn.
The only bits I can find for sale on Amazon or eBay are the same four that come with the Cybertool. The closest I can find is this "positive bit" phillips, which sounds like someone making a listing who doesn't have any clue that posidrive is actually a word. The picture of the product does look like a normal phillips to me, however. That being said, I don't know if I have ever seen a posidrive screw or screwdriver/bit in person before so I am hardly an expert on telling them apart.
Any idea where I can buy the normal phillips bit you speak of?
I was in a store during my vacation 2 weeks ago which had an INSANE stock and he had all bits available.
No such luck with my local retailer but you might want to check yours.Posidriv screws became more common then regular Philips here troughout the years.
Unfortunatly, Victorinox retail stores are hard to come by here in America. I checked google maps for them recently, and the only one that had existed in my entire state was marked as permanently closed. Gotta be online for order for me.
[/quote]That's a bummer :/
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login