And so it begins.... (My adventures into Alox!)
-
-
@MadPlumbarian said:
That's nice, pretty much perfect!
JR+1 That is a very tool dense minimal tool there

-
Ive been thinking about trying this for ages and well I finally am. Machining solid body tweezers from 0.125 Ti stock. Thats the exact thickness of the standard tweezers so by cutting out the profile from the side, I should end up with something that fits just right.
All of this is somewhat micro machining though since it's all going to be done with 1/16 and 1/32 end mills. 1/32 is tiny!

-
Oh sweet!
JR -
Hmmm -
Can the Tormach really machine that finely? I know if Syph is planning to do this - then he will have checked it out and it can! :) - Incredible :o
I guess the drill/machine head goes around the outside (and inside) of each of the tweezers and leaves the full block (frame) intact and fully bolted down at the cornersThese will look amazing - Can't wait to see them
- But it does seem like a big waste of Ti to me :(
-
Can the Tormach really machine that finely? I know if Syph is planning to do this - then he will have checked it out and it can! :) - Incredible :o
I guess the drill/machine head goes around the outside (and inside) of each of the tweezers and leaves the full block (frame) intact and fully bolted down at the cornersThese will look amazing - Can't wait to see them
- But it does seem like a big waste of Ti to me :(
That's a 2 inch by 4 inch piece of Ti. About 15 dollars of Ti to make 14 tweezers. The real cost is in broken endmills and I won't know that until I try.
The tormach has the resolution no problem.
-
Hey Syph - Thanks for coming back to us

So I guess quite a lot of waste - But not a lot of cost and still only $1 a tweezer - That seems worth it!!

And I guess quite a lot of milling time too.
Hope you don't get too many broken bits !!I guess if you worked in a foundry all the left overs would go back in the furnace.
I worked in a precision castings foundry once - where we used the inverted lost wax method to make the castings - All the leftover frames/trees just went back in the furnace, for the next run !
Sorry to harp on - Recycling and waste is one of my obsessions :-[
-
Do you think it is more viable, considering the surface finish and not having to do so much finishing on such tiny parts, to just mill it rather than waterjet cutting? Because of the sizes of mills you will have to use the first thing tht came to mind was the waterjet. But the finishing afterwards on such tiny parts, as I previously stated, made me think it would not be worth it. What are your thoughts?
BTW congrats, I'm glad that you're doing this for a living, I imagine it is really fun.
-
@WWW said:
Do you think it is more viable, considering the surface finish and not having to do so much finishing on such tiny parts, to just mill it rather than waterjet cutting? Because of the sizes of mills you will have to use the first thing tht came to mind was the waterjet. But the finishing afterwards on such tiny parts, as I previously stated, made me think it would not be worth it. What are your thoughts?BTW congrats, I'm glad that you're doing this for a living, I imagine it is really fun.
Waterjet finish is pretty rough ya and it also doesnt make perfectly perpendicular to the surface cuts. Not ideal for very thin components. Also I can work on a cutting strategy to keep supports in place on the outside while I cut the inside and tips, then cut the outsides last and leave little tabs. Only the very inside part will need the 1/32 bit the rest will be cut with the 1/16. I finished the Gcode so I can try it tomorrow.

-
@Syph007 said:
Waterjet finish is pretty rough ya and it also doesnt make perfectly perpendicular to the surface cuts. Not ideal for very thin components. Also I can work on a cutting strategy to keep supports in place on the outside while I cut the inside and tips, then cut the outsides last and leave little tabs. Only the very inside part will need the 1/32 bit the rest will be cut with the 1/16. I finished the Gcode so I can try it tomorrow.
Good luck!!!

-
First cuts went just fine... Now does it work?

-
+1

JR -

+1

JR


-
The suspense is killing me :ahhh :ahhh :ahhh

-
Me too! :ahhh

-
Syph,
Seeing the springy nature of the tweezers you're now working on reminds me that quite a while back, you were making liner locks for some 93mm mods you were doing at the time. Any chance that idea could translate to the 91mm mods you're doing?
Sent from my iPhone using Tapatalk
-
Well???

-
So how long before you start making your sak-s completely from the ground up? :D
-
The leaves of the tweezers were too thin. Machined fine though but I got a better idea on how to cut them and not need a tiny 1/32 bit.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
