And so it begins.... (My adventures into Alox!)
-
It's almost like it was with computers a few years ago. You buy one, you get home, take it out of the box and the damn thing is already of historical value... :o
-

Proud SAKMC member :)
-
Tried the same copper inlay I do for the cross, but for initials. It was not easy and I dont know if Id want to try again. But I got er done.
-
Nice job

JR -
That's nice, the initial pop at the right angle/lighting

Proud SAKMC member :)
-
Another work of art

Sent from my iPhone using Tapatalk
-
The initials turned out beautifully. Great looking SAK.
-
For some reason I dont trust photobucket anymore and I think I'll just continue to attach pics to the post.
Blue skeletonized!
-
Beauty!

Do you think the backside Philips on your ti customs like that can stand up to more torque than the stock vic?
Have you ever tested? >:D -
Oh that's sick

JR -
@Pablo O'Brien said:
Beauty!
Do you think the backside Philips on your ti customs like that can stand up to more torque than the stock vic?
Have you ever tested? >:DYes much more torque. I'd have to test to failure with a torque wrench but ti and a steel pivots beats soft aluminum and brass pins any day.
-
Always a lot of awesome in this thread when I visit it

-
Ive FINALLY come up with a way I like to hold all the scale tools people want. Drawing it up now in CAD then I can post what Im thinking of trying. The pen is still too thick to fit unless I can find an option for a thinner one, but regardless if this works I can fit ...
Toothpick
Tweezers
Small firesteel
Pin
Sewing needle and threadThat takes care of what most people would want, and there will be a small space left over to store whatever else could be jammed in there.
Ive been stuck forever trying to work out the mechanism. I know I could machine a little drawer hollow that opened in the scale, but how would it lock into place to avoid accidentally opening, and it would also have to be simple so that machining time/cost wasnt too much more and no extra parts like more screws and tapping would be needed.
I did have to go with much thicker Ti for the backscale 0.155" instead of the 0.100" I used now, but that at least this will provide a way to offer people what they want. It would still be slightly thinner than a stock SAK with plastic scales though (0.070" thinner) since it still wont have the outer liners. So still an ok compromise I think for those that would want this.
My breakthrough in mentally working on this was realizing how I could machine the drawer to have a built in retension spring to snap it home and become a solid part of the scale when not needed. A small nail nick would be exposed either on top on inside to pop it open. It would be part of the back scale and open upwards like a normal tool, but the hinge point would be towards the inside not where the normal tools pivot.
Began prototyping today. Very thick Ti scale pocketed out with pivot and locking bump on other end. Now to make the piece that fits in that space and holds the parts.

Im working on the fold out part today. This was my idea to allow it to lock since 0.050" thick Ti is nice and springy for say a pocket clip, I think this should leave me with a nice little tab to spring and click into the scale.
I wont know until I actually cut a piece and test it, but that's why they call it prototyping right.

-
Oh my, if you pull this off I'm refering to you as Sir Robert from then on...
-
@Mechanickal said:
Oh my, if you pull this off I'm refering to you as Sir Robert from then on...
-
The fit was almost perfect. The locking tab wasnt quite right, and was too thick at the bend area. I needed a pry tool to release it, and well it should be operable with finger pressure. Ver 2 will be better. I have some confidence this will work now though! :D




-
Brilliant - I was wondering how the spring would work
I had all sorts of weird visions in my head with separate scissor like springs, and was wondering how they would attach etc etcNow I get it
And as you said earlier .... the simpler the betterCan see the bottom looks quite thick and therefore unbendy - Bring on version 2.0 - Production version ??? :D
-
So Sir Robert it is then?
-
@Huntsman said:
Brilliant - I was wondering how the spring would work
I had all sorts of weird visions in my head with separate scissor like springs, and was wondering how they would attach etc etcNow I get it
And as you said earlier .... the simpler the better- Bring on version 2.0 - Production version ??? :D
Ya a good thickness for a Ti pocket clip is 0.050" thick and thats what I left there,... but a pocket clip has alot more length for leverage. Since this one is scrap now, what I'll do is grind away at the bottom to thin it until it feels just right, then measure that and adjust.
I also need to make the entire thing a bit longer. I needed exactly 2 inches of length and didnt account for the spring part taking up part of that.
-
That is awesome Syph :o Can't wait to see a full working version

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login