I Recently Converted My Alox Mod to Torx
-
As the title suggests, I recently converted Jalox (Urban Pioneer) to torx screws... Some may ask why. Answer is simple... I wasn't too happy with the brass pins I used. It is simply not strong enough for 93mm backsprings and tools. I would from time to time need to re-peen (if this is the correct term) the pin heads as some tools were developing play from use... Now I understand why Vic uses Nickel Silver for pins... Stronger they are...
Of course there are other benefits of using torx... No need to peen... Am still not good at peening... hahaha... There also much more convenient for assembling and disassembling...
OK. To be honest, I had no plans/intentions whatsoever of making a thread about torx conversions... I didn't take any pictures of the conversion process...Hey, I had no experiences prior to this... Focus was needed... ah ah ah... I did get some helpful tips from a good man, Tattoosteve99.
I'm dedicating this thread to you Steven.
Poncho65 and Pablo O'Brian. As requested... Hope it was helpful...
First things first, here's what is needed (apart from the normal tools required to mutilte your SAK) to do a conversion...
Obviously, some torx screws and pivot barrels.


The ones I used were 3mm and 2.5mm pivots and are about 0.5" long... Most common used are 1/8".
A couple of torx and a step drill

Some threadlocker

Hope I didn't forget anything else...
Btw, here's a pic of Jalox....

(To be continued in the next post). Stay tuned...
Sent from my iPhone using Tapatalk
-
First thing needed to do is to disassemble your SAK. There are lots of guides in the forum so I won't show them here.
Clean and wash all the parts afterwards. Hopefully you remembered to take pics of the tool layout, configuration and order...
Here's mine

I later realized that the order of the two backsprings at the bottom of the pic are wrong... Found out during assembly...
Next thing I did, is to pre-fit the torx screw on the scale pivot holes to see if it will sit flush... I want this conversion to be aesthetically pleasing and functional... Turns out OK on the outer holes... Just need to countersink the middle hole...
Here's were the step drill bit comes in...Now I don't have a drill press thingo... And I didn't want to mess up the alox scales I wanted to use any further than what I had already did... Don't ask how...

Luckily aluminum is soft... I wanted to do this really nice and slow, so my rotary tool (dremel) was out of the picture... I manually drilled by hand to make a counter sink... Kinda like carving...

Nice and slow... frequently eye balling until I was satisfied that it is flush...

Now were ready for assembly and fitting and mockup...
Sent from my iPhone using Tapatalk
-
Forgot to mention that I used a 4mm step drill.. which is about the same diameter as the torx screws I have...
As mentioned previously, I used a couple of 3mm and a 2.5mm pivot barrels... This means no drilling on the backspring and tools required... If 1/8" barrels are used, then get a 1/8" cobalt drill bit (I think) and drill all the pivot holes on each tool, liner, scale and back spring...
Torx a screw on each barrel and insert them in the hole on the scales...

Since the middle pivot is smaller than the other ones, I placed a longer screw to add strength... (a helpful tip from Tattosteve99)
Afterwards, I did my assembly... all the while thinking (are the pivots long enough for my build? Are they shorter or longer than required?)... Again I was lucky... The pivot lengths are just about right... No cutting required...
TIP: determining pivot length needed is trial and error or if your good at it, do some measurements. The goal is, once screw is in place nice and tight, there are no play on the tools and open/closes nicely... You know, that click and pop sound...
Once everything is done... I focused my attention a bit to the middle pivot as both screw ends should meet... so I had to remove a bit of length from the long screw by cutting with pliers and filing... once I was happy.. I moved on the the next step...
Applying threadlocks so that the screws wont move... Loctite 243 came highly recommended from an inquiry I had in a separate thread. (thanks to all the guys that helped out on this question)...
Only apply a very minimal amount on each screw end... if more than required is applied, it will be tough to unscrew in the future...
Then all that is needed is some minor adjustments on each screw so that tools are not so tight and not too loose either.

I guess that's all I did really...
Again, I hope this helps you Poncho and Pablo...
Sent from my iPhone using Tapatalk
-
Forgot to mention that the screws I had were T6... Though some may come in T8?

Sent from my iPhone using Tapatalk
-
This probably the most unorganized and unplanned thread I have made... sigh
Sent from my iPhone using Tapatalk
-
This is helping me understand how the mod works for sure! This is somewhat unrelated to the pivots but when you put your two openers opposite the phillips what did you have to do to fit them?
-
@gdoolittle said:
This is helping me understand how the mod works for sure! This is somewhat unrelated to the pivots but when you put your two openers opposite the phillips what did you have to do to fit them?2 opener backsprings are needed... flip one so that it will fit the bottle opener on the same end as the can opener... Reshape the phillips the same as the openers and enlarge the pivot hole...

Sent from my iPhone using Tapatalk
-

Very nice tiny tiny work

-
Very cool.

You got lucky with being able to use 3mm pivots I think... :) -
Awesome! This is one of my dream mods and will hopefully be made in the future. This thread will work for reference so thank you!!
It's not failure if you learn something from it
-
@Pablo O'Brien said:
Very cool.
You got lucky with being able to use 3mm pivots I think... :)Got lucky? Why go to all the trouble of drilling out the tools to 1/8" if 3mm pivots are available?
-
@Pablo O'Brien said:
Very cool.

You got lucky with being able to use 3mm pivots I think... :)Got lucky? Why go to all the trouble of drilling out the tools to 1/8" if 3mm pivots are available?
:D
Indeed... 3mm pivots don't seem to be common. :D -
Thanks Guys

The pivots were part of a deal I had with Tattoosteve99... An awesome guy and friend... A good person to deal with...
Sent from my iPhone using Tapatalk
-
-
Awesome and timely post.
Well done - l believe your approach is the simplest l have seen.
I too want to build an Alox with this exact layout.
I've been holding off on buying the 1/8" pivots from the recommended place as they have a $US 50 minimum order (not including postage) for overseas buyers.
A few questions;
-
What is the thread size of the torx screws and where did you buy them from? Are they metric?
-
Any idea of the source of the pivots?
-
l thought l read somewhere on this site that you have to counterbore the inner surface of the scales slightly for the pivots - l believe this is so that the pivots take the load rather that the screws? Is it OK not to do this?
Cheers
George
-
-
@george1 said:
Awesome and timely post.Well done - l believe your approach is the simplest l have seen.
I too want to build an Alox with this exact layout.
I've been holding off on buying the 1/8" pivots from the recommended place as they have a $US 50 minimum order (not including postage) for overseas buyers.
A few questions;
-
What is the thread size of the torx screws and where did you buy them from? Are they metric?
-
Any idea of the source of the pivots?
-
l thought l read somewhere on this site that you have to counterbore the inner surface of the scales slightly for the pivots - l believe this is so that the pivots take the load rather that the screws? Is it OK not to do this?
Cheers
George
Hi George,
I wouldn't be able to answer no.1 as I don't know... like I mention above, I source the pivots and screws from Tattoosteve99...
I didn't counterbore the inside scale holes as all of the pivots ends goes through the scale holes... This I forgot to mention above...
Sent from my iPhone using Tapatalk
-
-
Forgot to mention that the screws I had were T6... Though some may come in T8?

I was about to ask that, thanks.

Imagine if SAKs came with torx screws. Man, the hours of fun we would have had.
That's for sure...

Sent from my iPhone using Tapatalk
-
Thanks for this thread jaya
I had always wondered about the countersinking part
A very straight forward explanation and great pics to go with it
I may try this someday if I can source the parts needed
Maybe a Farmer X with a file and an electrician blade instead of the opener
:DSome of the way the mod goes just hadn't occurred to me, thus why I wanted to see the process

Excellent thread

-
Nice reference for those looking to attempt this mod.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login