Show off your Sak mod's!
-
The mod below started out as a MiniChamp which I carried for several months.
I also had a Classic Alox in orange that had seen it's fair share of use, and decided that I'd like to have an Alox MiniChamp. I disassembled both and, in the end, I didn't actually need all the tools from the MiniChamp, and ended up with an Alox Vagabond and another SAK with the leftovers (it need some tools from a very old Rambler that was already decommissioned - see picture 1).Now, I decided it was time to make a change, and while I was at it, I wanted to change the Alox scales with the silver ones from another Classic Alox that I had bought specifically for this mod several months ago (see picture 2).
One thing that I wanted was a USB drive right on my SAK, so, I purchased an USB Signature ??? (model 4.6125.TG64) to integrate with the Alox Vagabond.So, There you have it, a variation of the Alox Vagabond with a 64GB USB drive (the layout of the tools is purposely not the usual one, since I had to make sure that all tools could be used with the split ring for the lanyard). (see picture 3)
With the leftovers I assembled an Alox Rambler to offer to a friend.Very cool!

Isn't the SAK too heavy to be used as an USB drive? Doesn't it force the USB drive? You can use it directly in an USB port or do you need a cable?

Thanks!! The answer is below. The USB is actually detachable from the SAK.
@jaya_man said:
Nice mod... looking at the pic, usb drive is the removable version... cmiiw
Sent from my iPhone using Tapatalk
-
The mod below started out as a MiniChamp which I carried for several months.
I also had a Classic Alox in orange that had seen it's fair share of use, and decided that I'd like to have an Alox MiniChamp. I disassembled both and, in the end, I didn't actually need all the tools from the MiniChamp, and ended up with an Alox Vagabond and another SAK with the leftovers (it need some tools from a very old Rambler that was already decommissioned - see picture 1).Now, I decided it was time to make a change, and while I was at it, I wanted to change the Alox scales with the silver ones from another Classic Alox that I had bought specifically for this mod several months ago (see picture 2).
One thing that I wanted was a USB drive right on my SAK, so, I purchased an USB Signature ??? (model 4.6125.TG64) to integrate with the Alox Vagabond.So, There you have it, a variation of the Alox Vagabond with a 64GB USB drive (the layout of the tools is purposely not the usual one, since I had to make sure that all tools could be used with the split ring for the lanyard). (see picture 3)
With the leftovers I assembled an Alox Rambler to offer to a friend.Very cool!

Isn't the SAK too heavy to be used as an USB drive? Doesn't it force the USB drive? You can use it directly in an USB port or do you need a cable?

Thanks!! The answer is below. The USB is actually detachable from the SAK.
@jaya_man said:
Nice mod... looking at the pic, usb drive is the removable version... cmiiw
Sent from my iPhone using Tapatalk
I have a similar one, but it's the older version, thicker USB. It's detachable, too. I though this wasn't, being so slim.

-
@FInixNOver said:
I finally got my hands on a Pioneer Harvester, and decided to mod my SAK (I used to call it Electrician X) yet again, to add the wood saw the hawkbill/pruner blade and the can opener (this one was necessary to complete the set).Previously I started with a Pioneer X and an Electrician. Swapped the can opener of the X with the sheepsfoot blade, and ended up with the Pioneer Electrician X, and a Pioneer.
Then I added a pocket clip to it.Now I had to disassemble all 3, to get all the parts I needed for the final SAK (don't have a name for it yet).
I ended up with the 5 layer SAK I wanted, a single layer SAK, and a few leftover parts.
<u>5 Layer SAK:</u>
- Layer 1
Main blade / awl
- Layer 2
Wood saw
- Layer 3
Scissors
- Layer 4
Sheepsfoot blade / Hawkbill blade
- Layer 5
Can opener / Bottle opener
For the fourth layer, I had to use the spring from a main blade layer and also the awl spacer (since the spring is thicker), to make it work, otherwise I could have built 2 single layer SAK's.
<u>**Single Layer SAK **(still have to peen it - you can see it in the leftovers picture):</u>
- Layer 1
Main blade / awl
<u>Leftovers:</u>
2 openers layer springs
1 spacer
1 set of scales
1 Main blade
1 Awl
2 Bottle openers
Well, I wasn't completely happy with the fact that there were to many parts leftover (which could potentially be used to build another SAK) from assembling this SAK, and decided to take it apart again, and try to fit the layer 4 (Sheepsfoot blade / Hawkbill blade) with the openers backspring.
It was going well, and seemed it would work until the SAK was peened together... the backspring didn't provide enough tension for one of the blades.
This left me with a tough choice to make. Would I rebuild it back the way it was, or take, yet, another approach?
You know it! It required a bit of bending of the Hawkbill blade, and loosing the awl, but it turned out awlright!! :DI now have a 4 layer Alox SAK, which is now thinner and lighter (111g / 3.9oz), and was able to put together a Solo variation with awl, and a Pioneer.
<u>Current Layout:</u>
-
Layer 1
Main blade / Hawkbill blade -
Layer 2
Wood saw -
Layer 3
Scissors -
Layer 4
Sheepsfoot blade / Bottle opener



- Layer 1
-
I finally got my hands on a Pioneer Harvester, and decided to mod my SAK (I used to call it Electrician X) yet again, to add the wood saw the hawkbill/pruner blade and the can opener (this one was necessary to complete the set).
Previously I started with a Pioneer X and an Electrician. Swapped the can opener of the X with the sheepsfoot blade, and ended up with the Pioneer Electrician X, and a Pioneer.
Then I added a pocket clip to it.Now I had to disassemble all 3, to get all the parts I needed for the final SAK (don't have a name for it yet).
I ended up with the 5 layer SAK I wanted, a single layer SAK, and a few leftover parts.
<u>5 Layer SAK:</u>
- Layer 1
Main blade / awl
- Layer 2
Wood saw
- Layer 3
Scissors
- Layer 4
Sheepsfoot blade / Hawkbill blade
- Layer 5
Can opener / Bottle opener
For the fourth layer, I had to use the spring from a main blade layer and also the awl spacer (since the spring is thicker), to make it work, otherwise I could have built 2 single layer SAK's.
<u>**Single Layer SAK **(still have to peen it - you can see it in the leftovers picture):</u>
- Layer 1
Main blade / awl
<u>Leftovers:</u>
2 openers layer springs
1 spacer
1 set of scales
1 Main blade
1 Awl
2 Bottle openers
Well, I wasn't completely happy with the fact that there were to many parts leftover (which could potentially be used to build another SAK) from assembling this SAK, and decided to take it apart again, and try to fit the layer 4 (Sheepsfoot blade / Hawkbill blade) with the openers backspring.
It was going well, and seemed it would work until the SAK was peened together... the backspring didn't provide enough tension for one of the blades.
This left me with a tough choice to make. Would I rebuild it back the way it was, or take, yet, another approach?
You know it! It required a bit of bending of the Hawkbill blade, and loosing the awl, but it turned out awlright!! :DI now have a 4 layer Alox SAK, which is now thinner and lighter (111g / 3.9oz), and was able to put together a Solo variation with awl, and a Pioneer.
<u>Current Layout:</u>
- Layer 1
Main blade / Hawkbill blade
- Layer 2
Wood saw
- Layer 3
Scissors
- Layer 4
Sheepsfoot blade / Bottle opener

- Layer 1
-
I finally got my hands on a Pioneer Harvester, and decided to mod my SAK (I used to call it Electrician X) yet again, to add the wood saw the hawkbill/pruner blade and the can opener (this one was necessary to complete the set).
Previously I started with a Pioneer X and an Electrician. Swapped the can opener of the X with the sheepsfoot blade, and ended up with the Pioneer Electrician X, and a Pioneer.
Then I added a pocket clip to it.Now I had to disassemble all 3, to get all the parts I needed for the final SAK (don't have a name for it yet).
I ended up with the 5 layer SAK I wanted, a single layer SAK, and a few leftover parts.
<u>5 Layer SAK:</u>
- Layer 1
Main blade / awl
- Layer 2
Wood saw
- Layer 3
Scissors
- Layer 4
Sheepsfoot blade / Hawkbill blade
- Layer 5
Can opener / Bottle opener
For the fourth layer, I had to use the spring from a main blade layer and also the awl spacer (since the spring is thicker), to make it work, otherwise I could have built 2 single layer SAK's.
<u>**Single Layer SAK **(still have to peen it - you can see it in the leftovers picture):</u>
- Layer 1
Main blade / awl
<u>Leftovers:</u>
2 openers layer springs
1 spacer
1 set of scales
1 Main blade
1 Awl
2 Bottle openers
Well, I wasn't completely happy with the fact that there were to many parts leftover (which could potentially be used to build another SAK) from assembling this SAK, and decided to take it apart again, and try to fit the layer 4 (Sheepsfoot blade / Hawkbill blade) with the openers backspring.
It was going well, and seemed it would work until the SAK was peened together... the backspring didn't provide enough tension for one of the blades.
This left me with a tough choice to make. Would I rebuild it back the way it was, or take, yet, another approach?
You know it! It required a bit of bending of the Hawkbill blade, and loosing the awl, but it turned out awlright!! :DI now have a 4 layer Alox SAK, which is now thinner and lighter (111g / 3.9oz), and was able to put together a Solo variation with awl, and a Pioneer.
<u>Current Layout:</u>
- Layer 1
Main blade / Hawkbill blade
- Layer 2
Wood saw
- Layer 3
Scissors
- Layer 4
Sheepsfoot blade / Bottle opener

+1

Sent from my iPhone using Tapatalk
- Layer 1
-
-
Does anyone know how to coat the victorinox's blade black, I've tried the FeCl3 solution as a test and it didn't work. Sorry for my bad english :D
-
@Hoàng Lê said:
Does anyone know how to coat the victorinox's blade black, I've tried the FeCl3 solution as a test and it didn't work. Sorry for my bad english :D
I've red an article a few months ago explaining a blackening process with some simple chemicals.
I'll see if I can find it again.
Found!
Bookmarked it back then it seems.http://www.homemodelenginemachinist.com/showthread.php?t=2401
-
-
@Hoàng Lê said:
Does anyone know how to coat the victorinox's blade black, I've tried the FeCl3 solution as a test and it didn't work. Sorry for my bad english :D
I've red an article a few months ago explaining a blackening process with some simple chemicals.
I'll see if I can find it again.
Found!
Bookmarked it back then it seems.http://www.homemodelenginemachinist.com/showthread.php?t=2401
Thanks, you just saved the day :ahhh :ahhh
-
@Hoàng Lê said:
@Hoàng Lê said:
Does anyone know how to coat the victorinox's blade black, I've tried the FeCl3 solution as a test and it didn't work. Sorry for my bad english :D
I've red an article a few months ago explaining a blackening process with some simple chemicals.
I'll see if I can find it again.
Found!
Bookmarked it back then it seems.http://www.homemodelenginemachinist.com/showthread.php?t=2401
Thanks, you just saved the day :ahhh :ahhh
:salute:
No problem
-
Threw together a 'new' Alex Rambler for my keychain.


-
Nice job

-
Nice peening

Sent from my iPhone using Tapatalk
-
Behold: The Bailcrafter and Ronald Schroders soon to be finished Bushcrafter

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

