Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Juice S2 mod

Scheduled Pinned Locked Moved The Mod Squad
32 Posts 1 Posters 7.4k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Juice S2 mod
Juice S2 mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • BePrepared Offline
    BePrepared
    Posts: 418
    BePrepared Offline
    BePrepared
    wrote on last edited by
    #13 Quote Reply

      While it was nice having outside opening bit holder, I could not figure out an (easy) way to get them to lock. :think: So I went back to Plan A.

      <a href="http://imgur.com/6R8L3Du" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/6R8L3Du.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      I used a 3mm dia diamond file to finish opening up the hole in the package opener blade (taken from the NexTool TaoTool). I had trouble drilling out the hole, and the diamond file and some elbow grease finally did the job. I also used a Dremel to reshape the tang to match that from other juice pieces (i.e. the original blade.) I also kept the small bit holder, to keep this layer wide enough not to stop pliers and inside tools opening.

      <a href="http://imgur.com/V9lGKOQ" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/V9lGKOQ.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      I fitted the backspring to the package opener blade, and used wide washers opposite the small bit holder, to keep the backspring from moving across. The new blade also locks into open position. The small bit holder does not have a back spring fitted. This isn't such a bad thing as the small drivers will not be used with much force...

      <a href="http://imgur.com/U29N0Dp" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/U29N0Dp.jpg?1" alt="banner" style="max-width: 100%; height: auto;" /></a>

      I need to grind off some of the top edge of the package opener, as it sticks out too far. I may remove the small bit holder, and grind down the piece that holds the backspring, as it is too wide for a single blade and would block the pliers from opening/closing and the inside tools if I only had one blade inside. (Or find another juice with the right sized piece.) This would also mean both handles were same thickness.

      I think I'm close to a final set of tools/mod. I think I will get some proper pivots (oh, :rant: the shipping costs from the USA...! :rant: ) to finish it off. I had thought of putting back the scales, but ideally I'd like to use 4 different coloured scales... :drool: but would mean killing 3 more juices :( So maybe I stay with a skeletool look. :cheers:

      Merit Badges
      Mod User Hobo User
      1 Reply Last reply
      • BePrepared Offline
        BePrepared
        Posts: 418
        BePrepared Offline
        BePrepared
        wrote on last edited by
        #14 Quote Reply

          I didn't like the uneven sized handles, so I ground down the frame holding the package opener, reprofiled the mini bit holder to match a Juice shape, and cut down the mini screwdriver. I also took some material off the back of the package opener so the pliers touch. This is it:

          <a href="http://imgur.com/qctIvaU" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/qctIvaU.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

          The backspring for the package opener now also holds the mini bit holder in place (the holder is a bit tight, I may need to grind off a fraction of the bit holder, or it may work itself out with use).

          <a href="http://imgur.com/NOAOtOD" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/NOAOtOD.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

          The handles are now just about the same thickness. All tools open and close, and lock into open position.

          <a href="http://imgur.com/zjqjyCX" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/zjqjyCX.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

          I'm just about there with this. I think it deserves proper pivots, so I'll order these soon. The reason I started this was because I wanted something more EDC office friendly --- even the new Juice range (i.e. smaller) blades look a little aggressive in an office or on the streets. I'm happy with this! :tu: YMMV ;)

          Now all I need a name for this Juice contraption.... :think:

          Merit Badges
          Mod User Hobo User
          1 Reply Last reply
          • Vidar Offline
            Vidar
            Posts: 2,605
            Vidar Offline
            Vidar
            wrote on last edited by
            #15 Quote Reply

              The name is clearly the most important bit! :D

              Looking good. I didn't even think of elbow grease and diamond file for making that hole. Adapt and overcome I guess. :)

              Merit Badges
              MTo Anniversary Challenge
              1 Reply Last reply
              • Poncho65 Offline
                Poncho65
                Global Moderators
                Posts: 87,636
                Poncho65 Offline
                Poncho65
                Global Moderators
                wrote on last edited by
                #16 Quote Reply

                  Looking good so far :cheers: :like:

                  Merit Badges
                  BO Tools Level 2 Japanese PST Reviewer Photographer Axe User Fire Making Hacker Multitool Encyclopedia User OCD Squad Time Lord Level 1 Mod User Duct Tape Discontinued SAK/MT Challenge The SUPER Challenge EDC Pocket Dump Challenge Def's 50k Challenge LM Rebar Challenge Traditional Folder Challenge Gerber MP Challenge Modified SAK Challenge MTo Anniversary Challenge Victorinox SwissTool Challenge LM Surge Challenge Level 2 Victorinox Spirit Challenge MTO Rotation Challenge LM Wave Challenge Calendar   2017 Calendar  2018 Calendar 2019 LM Surge Challenge Level 3 Keychain Challenge LM Crunch 15 day Challenge LM OHT Challenge PST 30 Day Challenge Calendar 2020 14th Anniversary Anything Goes Challenge Skeletool 30 Day Challenge The Batman 30 Day Challenge Poker Face Challenge Daredevil challenge The 30 Day MiniTool Challenge 30 Day Locks Up Challenge One Piece Collector 30 Day Rhymes with Orange Challenge Bond 30 Day Challenge Wally Badge 30 Day Ratchet Challenge
                  1 Reply Last reply
                  • BePrepared Offline
                    BePrepared
                    Posts: 418
                    BePrepared Offline
                    BePrepared
                    wrote on last edited by
                    #17 Quote Reply

                      Here is the missing image (I deletaed the original from imgur by accident.)

                      <a href="http://imgur.com/7u30zkJ" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/7u30zkJ.jpg?1" alt="banner" style="max-width: 100%; height: auto;" /></a>

                      Merit Badges
                      Mod User Hobo User
                      1 Reply Last reply
                      • King_Gorilla Offline
                        King_Gorilla
                        Posts: 659
                        King_Gorilla Offline
                        King_Gorilla
                        wrote on last edited by
                        #18 Quote Reply

                          when you are all done, do you plan to put some scales back on or leave it with that skeleton look???

                          Merit Badges
                          Hacker Outdoor Cook The 30 Day MiniTool Challenge 30 Day Modular Tool Challenge Tool Box Challenge
                          1 Reply Last reply
                          • BePrepared Offline
                            BePrepared
                            Posts: 418
                            BePrepared Offline
                            BePrepared
                            wrote on last edited by
                            #19 Quote Reply

                              I put some 1/8" (3.175mm) copper rivets in, instead of the 3mm nut and bolt I had been using during testing (copper was only 1/8" diameter I could source easily in UK). But I don't think I can peen down the rivet well enough (my lack of skill, experience, and proper tools) to get a good finish and look, and the correct tightness/looseness I need to make all tools open nicely. But as I discovered, the tools are held tight partly by the force of the backsprings, not the rivet compression --- hence when people remove the scales (or say the scales rattle) it indicates some gap between the rivet head and steel frame, so I think there is some tolerance in there. Anyway, I think pivots would be better, so I finally ordered some from a USA, despite the international shipping costs.

                              I might put some scales on it. I don't like the two-colour standard scales (orange / steel) and would prefer full colour. My current scales are slightly damaged, so could go back on, but I have my eye on a damaged old style S2 on E-bay, and the scales from that would fit nicely! My IDEAL would be the new type colour scales form the Juices, but one of each colour! Orange, green, blue, yellow.... but I don't see myself doing that because of the cost and need to carefully remove the scales wiyhout too much damage.

                              So I may leave it skeletool-like, but I'm not sure. I'm also investigating a possible cerakote for the steel frame. Watch this space. :popcorn:

                              Merit Badges
                              Mod User Hobo User
                              1 Reply Last reply
                              • Sam Lim Offline
                                Sam Lim
                                Posts: 2,306
                                Sam Lim Offline
                                Sam Lim
                                wrote on last edited by Sam Lim
                                #20 Quote Reply

                                  For the scissors u would need some amount of tightness between the scales to work. I took apart my old xe6 and used back the original rivet though. I had no experience working with rivet. So my first one was rather bad. The other 3 were much better. I found out after the first one, the key was to how short u need to leave to properly peen a rivet.

                                  Merit Badges
                                  Advanced Modder
                                  1 Reply Last reply
                                  • Poncho65 Offline
                                    Poncho65
                                    Global Moderators
                                    Posts: 87,636
                                    Poncho65 Offline
                                    Poncho65
                                    Global Moderators
                                    wrote on last edited by
                                    #21 Quote Reply

                                      Can't wait to see it :popcorn: :like:

                                      Merit Badges
                                      BO Tools Level 2 Japanese PST Reviewer Photographer Axe User Fire Making Hacker Multitool Encyclopedia User OCD Squad Time Lord Level 1 Mod User Duct Tape Discontinued SAK/MT Challenge The SUPER Challenge EDC Pocket Dump Challenge Def's 50k Challenge LM Rebar Challenge Traditional Folder Challenge Gerber MP Challenge Modified SAK Challenge MTo Anniversary Challenge Victorinox SwissTool Challenge LM Surge Challenge Level 2 Victorinox Spirit Challenge MTO Rotation Challenge LM Wave Challenge Calendar   2017 Calendar  2018 Calendar 2019 LM Surge Challenge Level 3 Keychain Challenge LM Crunch 15 day Challenge LM OHT Challenge PST 30 Day Challenge Calendar 2020 14th Anniversary Anything Goes Challenge Skeletool 30 Day Challenge The Batman 30 Day Challenge Poker Face Challenge Daredevil challenge The 30 Day MiniTool Challenge 30 Day Locks Up Challenge One Piece Collector 30 Day Rhymes with Orange Challenge Bond 30 Day Challenge Wally Badge 30 Day Ratchet Challenge
                                      1 Reply Last reply
                                      • BePrepared Offline
                                        BePrepared
                                        Posts: 418
                                        BePrepared Offline
                                        BePrepared
                                        wrote on last edited by
                                        #22 Quote Reply

                                          My pivots arrived. I gave up waiting for a reply about cerakote coating the frame, and decided to assemble the Juice and use the original scales.

                                          The pivots needed some grinding/polishing down to get the right diameter (stick them in a dremel and applied a diamond file). It was fairly easy to shorten the pivots and screws too (grind down in a dremel).

                                          I put the unit back together, with all backsprings in place. It felt tighter using these pivots (1/8" versus the 3mm nut and bolt I used for testing) especially for the Philips drive. After about 10 minutes one of the backsprings broke. :'(

                                          <a href="https://imgur.com/yizZ8BS" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/yizZ8BS.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                          I still cannot find the other part of the backspring. The backspring just shot out of the Juice and hit the ceiling. Luckily it didn't hit me!

                                          I have one thin backspring left over, so I put that in, but it rattles and does not really hold the Philips driver firmly. Need to find another Juice for parts... ;) And the try again!

                                          Merit Badges
                                          Mod User Hobo User
                                          1 Reply Last reply
                                          • Don Pablo Offline
                                            Don Pablo
                                            Posts: 15,329
                                            Don Pablo Offline
                                            Don Pablo
                                            wrote on last edited by
                                            #23 Quote Reply

                                              :ahhh

                                              Could the pivots have broke the backspring?

                                              Merit Badges
                                              Pen Challenge Modified SAK Challenge MTo Anniversary Challenge 14th Anniversary Anything Goes Challenge 30 Day Bladeless Challenge
                                              1 Reply Last reply
                                              • BePrepared Offline
                                                BePrepared
                                                Posts: 418
                                                BePrepared Offline
                                                BePrepared
                                                wrote on last edited by
                                                #24 Quote Reply

                                                  I think it could be a combination of three things.

                                                  1. the pivots should be OK, as they are 1/8" and same diameter as original rivets, but my test unit used 3mm (not 3.125mm = 1/8") nut and bolt and I think this added some slack to the previous builds
                                                  2. the large backsprings for the plierhead and Philips were put back wrong way --- think of the 2 backsprings as left and right, and you can see small rounding on the corners. I put them back in wrong order, but it's hard to see the difference. I think in past I had done it in right order, and maybe that eased some pressure on the springs.
                                                  3. I've hit the backsprings a good few times with a hammer, to get them back into position :twak:

                                                  It didn't feel right when it was re-assembled, and I think it is down to (2) mostly, and a combination of the other factors probably didn't help.

                                                  But the good thing I did learn is that re-sizing the pivots isn't too hard. I had bought 12 and expected to damage 1 or 2, but so far (fingers crossed) they worked out OK. So I still have 2 sets of 4 for other projects.... (maybe a Squirt mod :D ).

                                                  And I I found the other broken end of the backspring.

                                                  Merit Badges
                                                  Mod User Hobo User
                                                  1 Reply Last reply
                                                  • BePrepared Offline
                                                    BePrepared
                                                    Posts: 418
                                                    BePrepared Offline
                                                    BePrepared
                                                    wrote on last edited by
                                                    #25 Quote Reply

                                                      Found an old Juice S2 on E-bay, and used backspring from that as replacement.

                                                      <a href="https://imgur.com/0lMkYBf" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/0lMkYBf.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                                      Just about done. Pivots and screws are ground down to about right size (maybe will do some minor touching up). Back springs in place, and work well. Decided to not add in the scales --- might try and paint the frame, but guess I need a decent acid etch primer. Not 100% sure about the thin bit driver, and was considering replacing it with USB memory, but still exploring that option.

                                                      Merit Badges
                                                      Mod User Hobo User
                                                      1 Reply Last reply
                                                      • BePrepared Offline
                                                        BePrepared
                                                        Posts: 418
                                                        BePrepared Offline
                                                        BePrepared
                                                        wrote on last edited by
                                                        #26 Quote Reply

                                                          Since I had the other parts from the spare S2 (and not enough plier backsprings to build a new juice) I decided to add them and go to a KF4 style. Backsprings fitted and all tools work, handles close properly, and pliers work.

                                                          <a href="https://imgur.com/3rWy6np" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/3rWy6np.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                                          The inside tools are standard. The knife and scissors are standard juice (old style long knife). I added the package opener from the TaoTool (black hooked and curved blade) and the small bit holder from a Wave. The tools at the opposite end of the black blade and small bit holder are the large and small flat drivers from the old style juice. I may usethe large flat driver as a mini pry-bar type tool, and the small flat driver may end up as a small awl.

                                                          <a href="https://imgur.com/bZpDDaF" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/bZpDDaF.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                                          <a href="https://imgur.com/pb2nRgM" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/pb2nRgM.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                                          Merit Badges
                                                          Mod User Hobo User
                                                          1 Reply Last reply
                                                          • BePrepared Offline
                                                            BePrepared
                                                            Posts: 418
                                                            BePrepared Offline
                                                            BePrepared
                                                            wrote on last edited by
                                                            #27 Quote Reply

                                                              Here's the latest installment

                                                              <a href="https://imgur.com/AHpSJe5" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/AHpSJe5.jpg?1" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                                              <a href="https://imgur.com/Ersg3Cl" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/Ersg3Cl.jpg?1" alt="banner" style="max-width: 100%; height: auto;" /></a>

                                                              I got some spare parts from wowaboro and this is the result!

                                                              Merit Badges
                                                              Mod User Hobo User
                                                              1 Reply Last reply
                                                              • zoidberg Offline
                                                                zoidberg
                                                                Posts: 38,161
                                                                zoidberg Offline
                                                                zoidberg
                                                                wrote on last edited by
                                                                #28 Quote Reply

                                                                  An excellent first badge, congrats. :tu: :like:

                                                                  1 Reply Last reply
                                                                  • Breezy12 Offline
                                                                    Breezy12
                                                                    Posts: 2,026
                                                                    Breezy12 Offline
                                                                    Breezy12
                                                                    wrote on last edited by
                                                                    #29 Quote Reply

                                                                      @zoidberg said:
                                                                      An excellent first badge, congrats. :tu: :like:

                                                                      agreed! :like:

                                                                      :cheers:

                                                                      Merit Badges
                                                                      Hacker Japanese PST Reviewer OCD Squad Flashlight Mod User Camping Paracord Outdoor Cook
                                                                      1 Reply Last reply
                                                                      • MusicMen Offline
                                                                        MusicMen
                                                                        Posts: 2,320
                                                                        MusicMen Offline
                                                                        MusicMen
                                                                        wrote on last edited by
                                                                        #30 Quote Reply

                                                                          Congratulations. :cheers:
                                                                          Great step by step explaination. :tu: :tu:

                                                                          Merit Badges
                                                                          Mod User Flashlight Duct Tape Carabiner User OCD Squad Hacker Gerber MP Challenge LM Juice Challenge Level 1 Titanium Time Lord Level 1 BO Tools Level 1 MTO Tool MTo Store User Zip Tie User MTo Anniversary Challenge Victorinox SwissTool Challenge Juice Collector Level 1 ALOX with Scissors
                                                                          1 Reply Last reply
                                                                          • BePrepared Offline
                                                                            BePrepared
                                                                            Posts: 418
                                                                            BePrepared Offline
                                                                            BePrepared
                                                                            wrote on last edited by
                                                                            #31 Quote Reply

                                                                              The story is not over yet! 8)

                                                                              I'm searching for some other parts, and will update this thread soon. Well, as soon as I get the pieces I need. :D

                                                                              :popcorn: :popcorn: :popcorn:

                                                                              Merit Badges
                                                                              Mod User Hobo User
                                                                              1 Reply Last reply

                                                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                              With your input, this post could be even better 💗

                                                                              Register Login

                                                                              1. Home
                                                                              2. Tool Talk
                                                                              3. The Mod Squad
                                                                              4. Juice S2 mod
                                                                              Reply
                                                                              • Reply as topic
                                                                              Log in to reply
                                                                              COMMUNITY LINKS
                                                                              EDC-TV SAKWiki GearFeed SAKSelector
                                                                              Operational Funds

                                                                              Help us keep the Unworkable working!

                                                                              Make A Donation
                                                                              November Goal: $300.00
                                                                              Due Date: Nov 30
                                                                              Total Receipts: $0.00
                                                                              Below Goal: $300.00
                                                                              0% funded
                                                                              • Login

                                                                              • Don't have an account? Register

                                                                              • Login or register to search.
                                                                              • First post
                                                                                Last post
                                                                              0