Juice S2 mod
-
For the scissors u would need some amount of tightness between the scales to work. I took apart my old xe6 and used back the original rivet though. I had no experience working with rivet. So my first one was rather bad. The other 3 were much better. I found out after the first one, the key was to how short u need to leave to properly peen a rivet.
-
Can't wait to see it

-
My pivots arrived. I gave up waiting for a reply about cerakote coating the frame, and decided to assemble the Juice and use the original scales.
The pivots needed some grinding/polishing down to get the right diameter (stick them in a dremel and applied a diamond file). It was fairly easy to shorten the pivots and screws too (grind down in a dremel).
I put the unit back together, with all backsprings in place. It felt tighter using these pivots (1/8" versus the 3mm nut and bolt I used for testing) especially for the Philips drive. After about 10 minutes one of the backsprings broke. :'(
<a href="https://imgur.com/yizZ8BS" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/yizZ8BS.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I still cannot find the other part of the backspring. The backspring just shot out of the Juice and hit the ceiling. Luckily it didn't hit me!
I have one thin backspring left over, so I put that in, but it rattles and does not really hold the Philips driver firmly. Need to find another Juice for parts... ;) And the try again!
-
:ahhh
Could the pivots have broke the backspring?
-
I think it could be a combination of three things.
- the pivots should be OK, as they are 1/8" and same diameter as original rivets, but my test unit used 3mm (not 3.125mm = 1/8") nut and bolt and I think this added some slack to the previous builds
- the large backsprings for the plierhead and Philips were put back wrong way --- think of the 2 backsprings as left and right, and you can see small rounding on the corners. I put them back in wrong order, but it's hard to see the difference. I think in past I had done it in right order, and maybe that eased some pressure on the springs.
- I've hit the backsprings a good few times with a hammer, to get them back into position

It didn't feel right when it was re-assembled, and I think it is down to (2) mostly, and a combination of the other factors probably didn't help.
But the good thing I did learn is that re-sizing the pivots isn't too hard. I had bought 12 and expected to damage 1 or 2, but so far (fingers crossed) they worked out OK. So I still have 2 sets of 4 for other projects.... (maybe a Squirt mod :D ).
And I I found the other broken end of the backspring.
-
Found an old Juice S2 on E-bay, and used backspring from that as replacement.
<a href="https://imgur.com/0lMkYBf" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/0lMkYBf.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Just about done. Pivots and screws are ground down to about right size (maybe will do some minor touching up). Back springs in place, and work well. Decided to not add in the scales --- might try and paint the frame, but guess I need a decent acid etch primer. Not 100% sure about the thin bit driver, and was considering replacing it with USB memory, but still exploring that option.
-
Since I had the other parts from the spare S2 (and not enough plier backsprings to build a new juice) I decided to add them and go to a KF4 style. Backsprings fitted and all tools work, handles close properly, and pliers work.
<a href="https://imgur.com/3rWy6np" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/3rWy6np.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
The inside tools are standard. The knife and scissors are standard juice (old style long knife). I added the package opener from the TaoTool (black hooked and curved blade) and the small bit holder from a Wave. The tools at the opposite end of the black blade and small bit holder are the large and small flat drivers from the old style juice. I may usethe large flat driver as a mini pry-bar type tool, and the small flat driver may end up as a small awl.
<a href="https://imgur.com/bZpDDaF" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/bZpDDaF.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="https://imgur.com/pb2nRgM" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/pb2nRgM.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
-
Here's the latest installment
<a href="https://imgur.com/AHpSJe5" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/AHpSJe5.jpg?1" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="https://imgur.com/Ersg3Cl" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/Ersg3Cl.jpg?1" alt="banner" style="max-width: 100%; height: auto;" /></a>
I got some spare parts from wowaboro and this is the result!
-
An excellent first badge, congrats.

-
Congratulations.

Great step by step explaination.

-
The story is not over yet! 8)
I'm searching for some other parts, and will update this thread soon. Well, as soon as I get the pieces I need. :D

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login