How to replace the blades with the openers elegantly.
-
So, update.
The only niggle I have with this mod is the snap on the bottle opener/cap lifter. Its not quite a nail breaker, but its easily two or three times more snappy than a stock configuration. And I believe that this is the reason:
Top is a bottle opener/cap lifter with old type round tang, and corresponding spring.
Middle is a main blade with corresponding spring.
Bottom is a bottle opener/cap lifter with new type square tang(+locking nub), and corresponding spring.Whats happening when I pair the new type bottle opener/cap lifter with a blade spring, is that the square tang is "pushing" out the spring more than it was designed to, when opening, hence the increased snap, if can understand my rambling.

You can see how on the spring for the square tang bottle opener/cap lifter, victorinox has shaped it so that the square tang doesn't push it out too much, and it retains the "just right" amount of snap.How to fix? Well...
You can grind the square tang into a round tang, very much not recommended due to difficulty.
:ahhh
Or grind a curve into the blade spring, not an easy peasy job, but not super duper hard like the above option.
Or use a old style bottle opener/cap lifter.

-
@Pablo O'Brien said:
So, update.
The only niggle I have with this mod is the snap on the bottle opener/cap lifter. Its not quite a nail breaker, but its easily two or three times more snappy than a stock configuration. And I believe that this is the reason:
Top is a bottle opener/cap lifter with old type round tang, and corresponding spring.
Middle is a main blade with corresponding spring.
Bottom is a bottle opener/cap lifter with new type square tang(+locking nub), and corresponding spring.Whats happening when I pair the new type bottle opener/cap lifter with a blade spring, is that the square tang is "pushing" out the spring more than it was designed to, when opening, hence the increased snap, if can understand my rambling.

You can see how on the spring for the square tang bottle opener/cap lifter, victorinox has shaped it so that the square tang doesn't push it out too much, and it retains the "just right" amount of snap.How to fix? Well...
You can grind the square tang into a round tang, very much not recommended due to difficulty.
:ahhh
Or grind a curve into the blade spring, not an easy peasy job, but not super duper hard like the above option.
Or use a old style bottle opener/cap lifter.

Or live with it, if its not too bad for you. Thats what I'm doing.
Forgot an option. See in bold.
It helps if you grab the nick as close to the tip as possible, for leverage. -
Nice!
Ya you cant just delete the blade layer or you get an ugly backscale with that cutout. The only other thing that works is to put the scissors layer on the back and put the corkscrew on it. Thats the only way Ive gone bladeless and kept the corkscrew.
-
Ya you cant just delete the blade layer or you get an ugly backscale with that cutout. The only other thing that works is to put the scissors layer on the back and put the corkscrew on it. Thats the only way Ive gone bladeless and kept the corkscrew.

That's another good option, what do you have to do to make the Corkscrew fit, besides adding washers?
-
@Pablo O'Brien said:
Nice!
Ya you cant just delete the blade layer or you get an ugly backscale with that cutout. The only other thing that works is to put the scissors layer on the back and put the corkscrew on it. Thats the only way Ive gone bladeless and kept the corkscrew.

That's another good option, what do you have to do to make the Corkscrew fit, besides adding washers?
I dont even add washers, the gap isnt enough to matter. All I do is bend the backspring a bit to give the scissors better closed snap. If you dont its pretty weak. Other than that I dont change a thing.
If the scissors dont rest quite right after, sometimes its necessary to grind the scissors rest down just 1 mm or so so the scissors go down inside the sak further. This isnt always needed though and I think depends on how hard or at what point I bend the scissors backspring. You'll see what I mean if you try.
-
It occurs to me that I haven't posted any pics of the finished SAK which I featured in the second post.

Reused pics... Until I take some more tomorrow.
Fair warning... Some people may feel conflicted about the toolset.
I call it the Slim Fishy.
Spoiler:


I'm very happy with it, despite the extra snap on the bottle opener/cap lifter. I'm not planning on taking it part anytime in the future, and it will ride in my EDC beside my "Mini Pabsman" (Thanks for the name Mags. ::) ) as a very complementary companion SAK.
-
That's a great combo Pabs
If you use the scaler as an eating implement you almost have a picnic knife there. And I love the Mini Pabsman 
Carry them both plus a 58mm and you're nearly committing an act of Schronogamy.
-
@Pablo O'Brien said:
@Pablo O'Brien said:
So, update.
The only niggle I have with this mod is the snap on the bottle opener/cap lifter. Its not quite a nail breaker, but its easily two or three times more snappy than a stock configuration. And I believe that this is the reason:
Top is a bottle opener/cap lifter with old type round tang, and corresponding spring.
Middle is a main blade with corresponding spring.
Bottom is a bottle opener/cap lifter with new type square tang(+locking nub), and corresponding spring.Whats happening when I pair the new type bottle opener/cap lifter with a blade spring, is that the square tang is "pushing" out the spring more than it was designed to, when opening, hence the increased snap, if can understand my rambling.

You can see how on the spring for the square tang bottle opener/cap lifter, victorinox has shaped it so that the square tang doesn't push it out too much, and it retains the "just right" amount of snap.How to fix? Well...
You can grind the square tang into a round tang, very much not recommended due to difficulty.
:ahhh
Or grind a curve into the blade spring, not an easy peasy job, but not super duper hard like the above option.
Or use a old style bottle opener/cap lifter.

Or live with it, if its not too bad for you. Thats what I'm doing.
Forgot an option. See in bold.
It helps if you grab the nick as close to the tip as possible, for leverage.A cheap 25 x 762 mm (1x30 inch) belt sander (https://www.machinemart.co.uk/p/scheppach-bts700-belt--disc-sander-230v/ or similar) is perfect for this kind of SAK modding and makes grinding tools a breeze. You can get all sorts of belts in different grits and materials for them. I get mine from: http://stores.ebay.co.uk/abrasivexpertjohnt1102/ - I use the 60 or 80 grit ones for shaping stainless.
-
@Pablo O'Brien said:
@Pablo O'Brien said:
So, update.
The only niggle I have with this mod is the snap on the bottle opener/cap lifter. Its not quite a nail breaker, but its easily two or three times more snappy than a stock configuration. And I believe that this is the reason:
Top is a bottle opener/cap lifter with old type round tang, and corresponding spring.
Middle is a main blade with corresponding spring.
Bottom is a bottle opener/cap lifter with new type square tang(+locking nub), and corresponding spring.Whats happening when I pair the new type bottle opener/cap lifter with a blade spring, is that the square tang is "pushing" out the spring more than it was designed to, when opening, hence the increased snap, if can understand my rambling.

You can see how on the spring for the square tang bottle opener/cap lifter, victorinox has shaped it so that the square tang doesn't push it out too much, and it retains the "just right" amount of snap.How to fix? Well...
You can grind the square tang into a round tang, very much not recommended due to difficulty.
:ahhh
Or grind a curve into the blade spring, not an easy peasy job, but not super duper hard like the above option.
Or use a old style bottle opener/cap lifter.

Or live with it, if its not too bad for you. Thats what I'm doing.
Forgot an option. See in bold.
It helps if you grab the nick as close to the tip as possible, for leverage.A cheap 25 x 762 mm (1x30 inch) belt sander (https://www.machinemart.co.uk/p/scheppach-bts700-belt--disc-sander-230v/ or similar) is perfect for this kind of SAK modding and makes grinding tools a breeze. You can get all sorts of belts in different grits and materials for them. I get mine from: http://stores.ebay.co.uk/abrasivexpertjohnt1102/ - I use the 60 or 80 grit ones for shaping stainless.
Thanks for the tip, I'll consider getting one.

-
LOL - only 85 quids :ahhh
-
-
:P But it really is very useful, and not just for SAK hacking. I miss not having somewhere to use mine.
-
Here's a cheaper solution if you have an electric drill:

-
Heh heh, I've realised that I have those things, for a dremel.

-
@Pablo O'Brien said:
Heh heh, I've realised that I have those things, for a dremel.
Problem solved! We've just saved 85 quids each!

-
@Pablo O'Brien said:

What's the facepalm for? I put the trolly back!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
