Supertool 300 VX upgrade (Mod badge request too)
-
The small bit can be wedged under the lock on the ST300. I just thought of this and tried it out, works pretty good



-
Just tried it on my Rebar and it also works

-
Just tried it too - it seems to work, at least to an extent... I wonder how much torque you can apply before you overcome the lock spring though, but then again you can apply additional finger pressure...
Edit: it would be ideal to have a more positively locking solution...
Sent on my SM-G930F with Tapatalk
-
I think it would work for most screws that small. I don't think you need a lot of torque. But yes Ideally you would have a more positive lock.
-


Sent on my SM-G930F with Tapatalk
-
The next iteration in the eternal quest for yet more versatility on the ST 300 VX.
I've ground down the surplus small bit holder along the lines above, taking into account the handle contour and drilled a 5.5 mm hole (this just about fits), then used a Wave pivot and a washer, all locked with the original ST pivot screw. Behold the pieces and the results. The pivot is a tad long, hence the need for the extra washer (about 1.5 mm thick). Let's see how this mod holds up - to obviate the need for the washer I might shorten the pivot a bit but that requires some serious thought as to fixing in the lathe... I might also play around with the position of the washer.
Parental advisory: no multitools were harmed in the process of this modification, as spare parts were used exclusively.




Sent on my SM-G930F with Tapatalk
-
Nice !

-
Thanks Steve

I have made a small modification to the setup. I found I preferred to have the washer on the other side of the handle - then I found out that the original pivot lock screw covered too little area, so I swapped it for the Wave counterpart, which could then make do with a thinner 0.9 mm washer (slightly ground off to match the handle contour). Much more pleasing to the eye, I think, but see for yourselves...



Sent on my SM-G930F with Tapatalk
-
excellent work, DT!

I am just now seeing this thread for the first time, and I am thoroughly impressed.

one question about the solution you came up with for the small bit driver... does it rotate around the pivot at all, or does it stay in place pretty well? it almost looks like the tool might benefit from a similar shaped block on the other pivot as well to hold it in place when the straight edges line up.
-
@Breezy12 said:
excellent work, DT!
I am just now seeing this thread for the first time, and I am thoroughly impressed.

one question about the solution you came up with for the small bit driver... does it rotate around the pivot at all, or does it stay in place pretty well? it almost looks like the tool might benefit from a similar shaped block on the other pivot as well to hold it in place when the straight edges line up.
Thanks! The small bit driver sits pretty tight. You'd have to use more force than you'd likely use on a small screw to pivot it. But the counterblock is a good idea... I have a washer there, ground off to face the handle slope to inhibit rotation on that side.
Sent on my SM-G930F with Tapatalk
-
Close up of side opposite small bit driver:

Sent on my SM-G930F with Tapatalk
-
cool idea
now i can use that on Blave and ReBlaster XXX -
excellent work, DT!

I am just now seeing this thread for the first time, and I am thoroughly impressed.

one question about the solution you came up with for the small bit driver... does it rotate around the pivot at all, or does it stay in place pretty well? it almost looks like the tool might benefit from a similar shaped block on the other pivot as well to hold it in place when the straight edges line up.
Thanks! The small bit driver sits pretty tight. You'd have to use more force than you'd likely use on a small screw to pivot it. But the counterblock is a good idea... I have a washer there, ground off to face the handle slope to inhibit rotation on that side.
Looks great... really nice work

you're probably right about the amount of force it would take to actually cause the small bit driver to rotate while you're using it... but I figured it was still worth asking about. ;)
-
Blave with Mini Bits
Thank Boss


-
@Obi1shinobee said:
Blave with Mini Bits
Thank Boss

Ah, you left it pivotable did you? Nice
and you're very welcome! I wanted it smaller, compact and fixed - on the few occasions I'll likely be using the small driver, I'll get it out of the bit card and insert it in the ST.Sent on my SM-G930F with Tapatalk
-
Blave with Mini Bits :multi: :multi: :multi: Thank Boss :cheers: :cheers: :cheers:
Ah, you left it pivotable did you? Nice :like: and you're very welcome! I wanted it smaller, compact and fixed - on the few occasions I'll likely be using the small driver, I'll get it out of the bit card and insert it in the ST.
Sent on my SM-G930F with Tapatalk
Yes i can move in and out easy.. NOW FOR HAMMER TIME MODS................ :ahhh :ahhh :ahhh :ahhh
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
Planning a hammer, or something else?

Sent on my SM-G930F with Tapatalk
-
@Dutch_Tooler said:
Planning a hammer, or something else?

Sent on my SM-G930F with Tapatalk
Yes HAMMER TIME !!!!!!!!!!!!!!

-
I will add mini bits infront like ur ST300VX and add another Knife on it. muahahahaha MORE DEADLY


-
Or Marlins Spike :ahhh :ahhh :ahhh


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login