Leatherman Wave external scissors mod
-
excellent work!!

-
Awesome! You should start a side gig making parts that should exist but don't. A hard metal MUT scrapper would sell like hot cakes!
-
Scraper (1 p)?
Sent on my SM-G930F with Tapatalk
-
@tommywp said:
Awesome! You should start a side gig making parts that should exist but don't. A hard metal MUT scrapper would sell like hot cakes!Do you mean one of these things:
Carbon Scraper | Leatherman
Bronze replacement carbon scraper for the MUT® and MUT® EOD. Official Online Store of Leatherman, your trusted source of multi-tools since 1983.
Leatherman (www.leatherman.com)
Yea that doesn't look too difficult. What are they for? Can you send me dimensions for it and a few photos so I can CAD it up?
-
@Gerhard Gerber said:
I am using N690 Bohler stainless
So the scissors are better than anything else on the LM!

Excellent mod!

Sounds better than none of my LMs and all of my SAKs.
Do you know what steel LM use for the tools other than the knives?
I need move to New Zealand .. hahahaha

-
To my knowledge all tools (not just knife) are made out of 420 hc.
Awesome scissors! CNC access... experimental plier heads maybe?
-
@Wallace72 said:
To my knowledge all tools (not just knife) are made out of 420 hc.Awesome scissors! CNC access... experimental plier heads maybe?
Yea mate. If you have some cool ideas send them through and I can try and make them.
-
To my knowledge all tools (not just knife) are made out of 420 hc.
Awesome scissors! CNC access... experimental plier heads maybe?
Yea mate. If you have some cool ideas send them through and I can try and make them.
Spring action pliers?

-
To my knowledge all tools (not just knife) are made out of 420 hc.
Awesome scissors! CNC access... experimental plier heads maybe?
Yea mate. If you have some cool ideas send them through and I can try and make them.
Spring action pliers?

Yea good idea. I will look into it.
-
New Page Banana Dance!

I'm imagining a small torsion(?) spring inside the pivot.
-
I think that's what Evil did: /post/1092372
Perhaps external would be better then...

-
Excellent mod.

-
New Page Banana Dance!

I'm imagining a small torsion(?) spring inside the pivot.
Yea that would be cool as! I wonder whether you could keep the strength in the pivot if you hogged it out enough to put a spring in it. Worth a look though.
That's where the factory sprung pliers fall down in my opinion. As they tend to be made from cast components, and the inside is hollow, the load is focused on a smaller area of both the bore in the pliers, and the pivot. This increases the wear, and reduces the lifespan. Even in you improved the material used for the pliers, the pivot is soft, otherwise it wouldn't displace to form the rivet heads holding the two halves of the pliers together.
The only way I can think of to make a hardened and therefore more wear resistant pivot would be to thread it, so that it is similar to the old Victorinox scissors. Moving this on a step further, if the movable half of the pliers and the mating face of the pivot was tapered, you would actually be able to take up the slack when wear does start to happen. Drilling it for a pin spanner would probably be the most sensible way of driving this. The threaded section would need loctiteing to make sure the pivot stayed fixed relative to this, and didn't work itself undone with pliers use. This construction would also let you inside for servicing should the torsional spring let go / fail.

-
Interesting thoughts...
Where do MT pliers generally break? For some reason I have a picture in my head of it being between the plier pivot and the handle pivot.

-
@Syncop8r said:
Interesting thoughts...Where do MT pliers generally break? For some reason I have a picture in my head of it being between the plier pivot and the handle pivot.

Most breakages that I've seen are one jaw snapping off (i.e. forward of the main pivot, where the jaw starts). That's not too common though, I don't believe. Usually from pushing a tool well past it's limits, or a defective casting. The hollow ones (with integral springs) do seem to wear too easily though, not necessarily resulting in breakage, but definitely imparing performance (particularly on the cutters)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login