Leatherman Wave external scissors mod
-
@Wallace72 said:
To my knowledge all tools (not just knife) are made out of 420 hc.Awesome scissors! CNC access... experimental plier heads maybe?
Yea mate. If you have some cool ideas send them through and I can try and make them.
-
To my knowledge all tools (not just knife) are made out of 420 hc.
Awesome scissors! CNC access... experimental plier heads maybe?
Yea mate. If you have some cool ideas send them through and I can try and make them.
Spring action pliers?

-
To my knowledge all tools (not just knife) are made out of 420 hc.
Awesome scissors! CNC access... experimental plier heads maybe?
Yea mate. If you have some cool ideas send them through and I can try and make them.
Spring action pliers?

Yea good idea. I will look into it.
-
New Page Banana Dance!

I'm imagining a small torsion(?) spring inside the pivot.
-
I think that's what Evil did: /post/1092372
Perhaps external would be better then...

-
Excellent mod.

-
New Page Banana Dance!

I'm imagining a small torsion(?) spring inside the pivot.
Yea that would be cool as! I wonder whether you could keep the strength in the pivot if you hogged it out enough to put a spring in it. Worth a look though.
That's where the factory sprung pliers fall down in my opinion. As they tend to be made from cast components, and the inside is hollow, the load is focused on a smaller area of both the bore in the pliers, and the pivot. This increases the wear, and reduces the lifespan. Even in you improved the material used for the pliers, the pivot is soft, otherwise it wouldn't displace to form the rivet heads holding the two halves of the pliers together.
The only way I can think of to make a hardened and therefore more wear resistant pivot would be to thread it, so that it is similar to the old Victorinox scissors. Moving this on a step further, if the movable half of the pliers and the mating face of the pivot was tapered, you would actually be able to take up the slack when wear does start to happen. Drilling it for a pin spanner would probably be the most sensible way of driving this. The threaded section would need loctiteing to make sure the pivot stayed fixed relative to this, and didn't work itself undone with pliers use. This construction would also let you inside for servicing should the torsional spring let go / fail.

-
Interesting thoughts...
Where do MT pliers generally break? For some reason I have a picture in my head of it being between the plier pivot and the handle pivot.

-
@Syncop8r said:
Interesting thoughts...Where do MT pliers generally break? For some reason I have a picture in my head of it being between the plier pivot and the handle pivot.

Most breakages that I've seen are one jaw snapping off (i.e. forward of the main pivot, where the jaw starts). That's not too common though, I don't believe. Usually from pushing a tool well past it's limits, or a defective casting. The hollow ones (with integral springs) do seem to wear too easily though, not necessarily resulting in breakage, but definitely imparing performance (particularly on the cutters)
-
:'( I want one :'( :'( :'( :'( -
I have wondered about a springy bar that you can flick out from one of the handles and it presses (whilst bending) against the other handle... giving optional spring action...
-
@50ft-trad said:
I have wondered about a springy bar that you can flick out from one of the handles and it presses (whilst bending) against the other handle... giving optional spring action...
A bigger version of the Squirt mechanism would be easier
Interesting... I've never had a good look at a squirt.

I'm thinking more of a way of modifying existing pliers to have spring action rather than designing whole new ones with it integrated. -
Great mod. Looks like you're going to be one to follow on here now. So.......when are you setting up a storefront and taking orders?
-
Hi Guys,
Thought I should give you an update on my progress with this little project. I have now cut the two blades out of the stainless (Bohler n690). It all went reasonably well however there was a small gash in the part as the blade got a piece of swarf stuck under it lifting it off the clamping jig.
Now I will send them off to heat treat when I have a few other blades to go with them and see how that goes. I have a very slight bow in the blades to try to get them to cut nicely and I am a little concerned they may warp during heat treatment but we will just have to see.....
-

Sent on my SM-G930F with Tapatalk
-
CDub,
Are you planning on making these available?
Thanks Much!
-V-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
