Show me your drills
-
Great drills and impacters guys
Yet another something I need to get pics of :ahhh :D -
except that the thread's title is unfortunate and misleading ::) and that I don't have a power drill but I'd appreciate some education on the matter because I am interested in acquiring one. Possibly one from LIDL's PARKSIDE line as I've heard pretty good things about them and they have a 3-year guarantee.
When it comes to a cordless drill I think that there are two ways to go:
1- Find a manufacturer that will warranty the battery for a long period of time so that when yours starts to get weak and soft after 3 years, you can get another one with no hassle.
2- Buy an inexpensive drill and expect that you will be replacing it in three years.
Three years seems to be (usually) about as long as a drill works for me. My first cordless drill was a big Craftsman around 2000 and it was great, but a few years later the prices had come down, the power had gone up and replacing the battery on my Craftsman cost way more than a newer, more powerful drill. Ordinarily I would suggest just buying an inexpensive drill and expect to replace it in three years, but as Marc pointed out, some drills do carry a good warranty that includes the battery, and, given the choice, I think that's what I would do.
That's the best advice I can give....
My old Craftsman was $300. When I replaced it, I got a Kawasaki set for $300. It was similar to the set below, except I didn't get the flashlight. It was a reciprocating saw, circular saw, drill, two batteries and charger for $300.

I then found just the drill (exact same model) at another store for $50, and it came with two batteries and a charger, so now I had four tools (recip saw, circular saw and two drills), a battery for each tool, and two chargers that I could use to charge the batteries about as fast as I could drain them. I got to the point where I liked having two drills at the same time, because I could leave the drill bit in one and a screwdriver bit in the other and do a job a lot faster than having to constantly switch back and forth.
That was a great setup when it worked, but as the batteries eventually went soft I ended up having to replace almost an entire workshop of tools. I ended up getting a corded DeWalt drill for heavy stuff, my little B&D drill for light stuff, a corded reciprocating saw and I never did get a replacement circular saw, although since I have a big Craftsman table saw it wasn't needed as much.
This is the DeWalt drill I got:

This is the DeWalt Reciprocating saw:

And this is my big table saw, which comes off the legs and is surprisingly portable.
I wouldn't want to carry it too far, but it's really easy to load in the Jeep and take to wherever I want.
Def
-
Had a bit of an epiphany just over a year ago talking to the shop fitters busy at a new satellite office, they've switched over to battery powered power tools exclusively.
Personally I own none, and a lot of water will run into the ocean before I do

I've got a Ryobi pencil grinder, average size hand drill, angle grinder and a large Ryobi drill press......all run on 220V.
Good to see how the technology has improved and matured, simply not something I need.
-
Something tells me I will be digging out a couple of
toystools for the camera tomorrow. -
@Gerhard Gerber said:
Had a bit of an epiphany just over a year ago talking to the shop fitters busy at a new satellite office, they've switched over to battery powered power tools exclusively.Personally I own none, and a lot of water will run into the ocean before I do

I've got a Ryobi pencil grinder, average size hand drill, angle grinder and a large Ryobi drill press......all run on 220V.
Good to see how the technology has improved and matured, simply not something I need.
There is definitely a need for cordless tools. I really enjoy using them and not having to worry about running (or tripping on!) extension cords and so on. Get the tool that suits your needs. I have both because I see a good need for both.
Def
-
@Grant Lamontagne said:
@Gerhard Gerber said:
Had a bit of an epiphany just over a year ago talking to the shop fitters busy at a new satellite office, they've switched over to battery powered power tools exclusively.
Personally I own none, and a lot of water will run into the ocean before I do

I've got a Ryobi pencil grinder, average size hand drill, angle grinder and a large Ryobi drill press......all run on 220V.
Good to see how the technology has improved and matured, simply not something I need.
There is definitely a need for cordless tools. I really enjoy using them and not having to worry about running (or tripping on!) extension cords and so on. Get the tool that suits your needs. I have both because I see a good need for both.
Def
There is nothing quite like putting a few good sized holes in conctrete (or whatever) without a cord in sight.
-
@Grant Lamontagne said:
@Gerhard Gerber said:
Had a bit of an epiphany just over a year ago talking to the shop fitters busy at a new satellite office, they've switched over to battery powered power tools exclusively.
Personally I own none, and a lot of water will run into the ocean before I do

I've got a Ryobi pencil grinder, average size hand drill, angle grinder and a large Ryobi drill press......all run on 220V.
Good to see how the technology has improved and matured, simply not something I need.
There is definitely a need for cordless tools. I really enjoy using them and not having to worry about running (or tripping on!) extension cords and so on. Get the tool that suits your needs. I have both because I see a good need for both.
Def
There is nothing quite like putting a few good sized holes in conctrete (or whatever) without a cord in sight.
It's wizardry! :ahhh :ahhh
-
It's wizardry! :ahhh :ahhh
[/quote]
Electrickery! -
-
@Grant Lamontagne said:
When it comes to a cordless drill I think that there are two ways to go:1- Find a manufacturer that will warranty the battery for a long period of time so that when yours starts to get weak and soft after 3 years, you can get another one with no hassle.
2 - Buy an inexpensive drill and expect that you will be replacing it in three years.
I can't say I have experience with lots of brands, but I can say that the blue Bosch series of tools are generally high quality. As for cordless drills I got one of their cordless 14,4v series (the heavy "brute") which must be 12-13 years by now and still going strong. Also got the successor model to that and an impact driver both of which is likely some 10-11 years and also going strong. Still a bit on the fence with their 10.8v series though; 2 batteries have died way too early for my liking.
As for inexpensive cordless drills I've never had any success - they seem to cut most of their cost corners on the batteries. If you only need to do a hole now and then maybe still fine? Some years since I tried last time though - might have improved with the general quality increase of batteries?
Inexpensive corded tools on the other hand tend to be surprisingly good value for money as long as you don't drag them around outside in snow or rain or dusty places. They might be off in some ergonomic/ precision/ general hassle way but generally well worth it.
-
Talking of drilling holes and such like, I used these for the first time today - they were quite impressive.
Alpen Multicut bits:

-
It will take a special situation for me to ever go corded again.
My very well used Makitas. That rotary hammer

-
@moonweasel said:
It will take a special situation for me to ever go corded again.For me that depends on the nature of the work at hand. If the tools can stay put at a workstation and the work to be done passes by there then corded works great. And with less hassle with batteries. On the other hand if you need to bring the tools to the work then cordless is the winner.
-
A few of mine,Bosch,B&D and a few old hand drills :D



-
the grinder of stubs and nubs
-
Small drill

Small holes (0,4 mm)

-
Nice drill!
I once had the good fortune to be standing near an engineer and a machinist arguing about ultra tiny holes. They were making some kind of laser system for a helicopter and the engineer was specifying a hole that was extremely small, although I don't recall the exact sizing. The machinist was trying to explain to the engineer that a hole that size was impossible to drill because the heat of the drilling would cause the metal to expand to the point where it was basically self-healing, and even if it didn't, any temperature change would probably close the hole or distort it to the point where the precise calculations were messed up anyway. The engineer (as many do ::)) was arguing that the specs said the hole had to be that size, and that was the end of it.
I wonder how much further that project got before it was canned after some "unknown failure?" :D
Every time I see or hear about someone drilling small holes I think of that story and it always brings a smile to my face!
Def
-
I agree with the engineer...
One should always agree with the engineer. -
@Marc_in_NS said:
I agree with the engineer...
One should always agree with the engineer.Well... i'd expect just as much from a podgerphobe!!!
I on the other hand agree with the machinist.
:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

;)