Show me your drills
-
@Grant Lamontagne said:
@Gerhard Gerber said:
Had a bit of an epiphany just over a year ago talking to the shop fitters busy at a new satellite office, they've switched over to battery powered power tools exclusively.
Personally I own none, and a lot of water will run into the ocean before I do

I've got a Ryobi pencil grinder, average size hand drill, angle grinder and a large Ryobi drill press......all run on 220V.
Good to see how the technology has improved and matured, simply not something I need.
There is definitely a need for cordless tools. I really enjoy using them and not having to worry about running (or tripping on!) extension cords and so on. Get the tool that suits your needs. I have both because I see a good need for both.
Def
There is nothing quite like putting a few good sized holes in conctrete (or whatever) without a cord in sight.
-
@Grant Lamontagne said:
@Gerhard Gerber said:
Had a bit of an epiphany just over a year ago talking to the shop fitters busy at a new satellite office, they've switched over to battery powered power tools exclusively.
Personally I own none, and a lot of water will run into the ocean before I do

I've got a Ryobi pencil grinder, average size hand drill, angle grinder and a large Ryobi drill press......all run on 220V.
Good to see how the technology has improved and matured, simply not something I need.
There is definitely a need for cordless tools. I really enjoy using them and not having to worry about running (or tripping on!) extension cords and so on. Get the tool that suits your needs. I have both because I see a good need for both.
Def
There is nothing quite like putting a few good sized holes in conctrete (or whatever) without a cord in sight.
It's wizardry! :ahhh :ahhh
-
It's wizardry! :ahhh :ahhh
[/quote]
Electrickery! -
-
@Grant Lamontagne said:
When it comes to a cordless drill I think that there are two ways to go:1- Find a manufacturer that will warranty the battery for a long period of time so that when yours starts to get weak and soft after 3 years, you can get another one with no hassle.
2 - Buy an inexpensive drill and expect that you will be replacing it in three years.
I can't say I have experience with lots of brands, but I can say that the blue Bosch series of tools are generally high quality. As for cordless drills I got one of their cordless 14,4v series (the heavy "brute") which must be 12-13 years by now and still going strong. Also got the successor model to that and an impact driver both of which is likely some 10-11 years and also going strong. Still a bit on the fence with their 10.8v series though; 2 batteries have died way too early for my liking.
As for inexpensive cordless drills I've never had any success - they seem to cut most of their cost corners on the batteries. If you only need to do a hole now and then maybe still fine? Some years since I tried last time though - might have improved with the general quality increase of batteries?
Inexpensive corded tools on the other hand tend to be surprisingly good value for money as long as you don't drag them around outside in snow or rain or dusty places. They might be off in some ergonomic/ precision/ general hassle way but generally well worth it.
-
Talking of drilling holes and such like, I used these for the first time today - they were quite impressive.
Alpen Multicut bits:

-
It will take a special situation for me to ever go corded again.
My very well used Makitas. That rotary hammer

-
@moonweasel said:
It will take a special situation for me to ever go corded again.For me that depends on the nature of the work at hand. If the tools can stay put at a workstation and the work to be done passes by there then corded works great. And with less hassle with batteries. On the other hand if you need to bring the tools to the work then cordless is the winner.
-
A few of mine,Bosch,B&D and a few old hand drills :D



-
the grinder of stubs and nubs
-
Small drill

Small holes (0,4 mm)

-
Nice drill!
I once had the good fortune to be standing near an engineer and a machinist arguing about ultra tiny holes. They were making some kind of laser system for a helicopter and the engineer was specifying a hole that was extremely small, although I don't recall the exact sizing. The machinist was trying to explain to the engineer that a hole that size was impossible to drill because the heat of the drilling would cause the metal to expand to the point where it was basically self-healing, and even if it didn't, any temperature change would probably close the hole or distort it to the point where the precise calculations were messed up anyway. The engineer (as many do ::)) was arguing that the specs said the hole had to be that size, and that was the end of it.
I wonder how much further that project got before it was canned after some "unknown failure?" :D
Every time I see or hear about someone drilling small holes I think of that story and it always brings a smile to my face!
Def
-
I agree with the engineer...
One should always agree with the engineer. -
@Marc_in_NS said:
I agree with the engineer...
One should always agree with the engineer.Well... i'd expect just as much from a podgerphobe!!!
I on the other hand agree with the machinist.
:D
-
I agree with the engineer...
One should always agree with the engineer.Well... i'd expect just as much from a podgerphobe!!!
I on the other hand agree with the machinist.
Podgering phobia!!!!
Is that becoming a thing?:D
-
@Marc_in_NS said:
I agree with the engineer...
One should always agree with the engineer.I wish I could.... but I have had too many experiences with an engineer to believe they are the answer to everything they would have you believe.

While dealing with wood pellets a few years ago I got into a discussion with the in house engineer, who insisted that I was not allowed to bring my flashlight into the facility because it was not classified as "intrinsically safe," a point he was absolutely correct on. However, I upset him with a thing called logic when I pointed out that the flashlight was waterproof, and water molecules are both smaller and more pervasive than wood dust, and therefore it was safe for the environment we were working in. "Intrinsically safe" is a term used for hazardous environments, which includes gases, but wood dust does not release dangerous gases, the dust particles themselves ignite and cause a very unhappy chain reaction- which, by the way, I have no interest in experiencing first hand. And yet, I felt safe using this flashlight because the electrical source was well insulated from the outside, combustible particles.
He threw a fit and threatened to have me removed from the site, which would have been very disastrous for him as I represent the buyer... and getting rid of me also gets rid of a big expensive customer. :P
Never use logic against an engineer- many of them missed the day they taught common sense in engineer school, but they obviously did not miss the day they taught ego.

Not a shot against engineers- I know many that are much better than that, but I also know too many that don't let reality encroach on what a book and documented specs tell them.
Def
-
@Grant Lamontagne said:
The machinist was trying to explain to the engineer that a hole that size was impossible to drill because the heat of the drilling would cause the metal to expand to the point where it was basically self-healing, and even if it didn't, any temperature change would probably close the hole or distort it to the point where the precise calculations were messed up anyway.Traditional drilling runs into problems at a given size, high depth to diameter ratios, or just smurfing hard materials. Then other technologies like electro discharge machining (EDM) takes over.
Basically EDM works by emitting high voltage discharges where each discharge removing a tiny bit of material as it goes along. Because the work end never physically touches the material it is going through it can make tiny holes of great depth regardless of hardness. (Provided the material in question is conductive).
Ok, that was the weird diversion of the day ::)
-
Absolutely, but when the hole is so small and is required to be a precise size, virtually any temperature variance will throw it out of calibration, which was the point.
Def
-
@Grant Lamontagne said:
Absolutely, but when the hole is so small and is required to be a precise size, virtually any temperature variance will throw it out of calibration, which was the point.Def
EDM drilling uses a continous fluid flow at high pressure which emits at the very end of the drill pipe. That provides electrical insulation and removal of the disharged material, and to the extend necessary also cooling. (Making a tiny 0,08mm diameter hole in a big chuck of metal doesn't necessarily add that much heat to begin with).
Similarly traditional drills for machining centers can be had with through drill flow for cooling and chip removal. (Example http://s3.cnccookbook.com/img/CNCCookbook/tsc-drill-bit.jpg). If really precise calibrated holes are needed then twisted drills are usually not precise enough anyway, and so need to be followed by other methods like reaming or boring.
A third option for minimizing heat using traditional drills is too simply go very slow but still with the correct pressure and cutting depth per rotation. I once saw a weird machine for doing exactly that. I have no idea what that was actually used for. (Well, doh, making holes..
).I have seen an old advert from around 1900 for a very portable mechanical contraption that did the same slow drilling. I'd actually like to have that one - would be a great portable solution for making controlled holes in stuff.
Talking about heat another offbeat drill method exploits exactly that. Flowdrilling will basically rotate and heat the material until it deforms into a hole with a suitable collar formed by the moved leftover material. Typically used for making threaded bolt connections in sheet metal.
I think the point I was trying to make was that there are often alternative technologies out there for many common problems, but which are rarely encountered or well known in the public.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
;)