old Champ rebuild
-
Oooo, this is exciting Twiglet


-
First step was to gather all the original parts and source all the new ones, which required disassembly of 5 (!) knives. Disassembly of the original will make 6, a bit of a costly project.

Here's all the new stuff.


-
I was also considering adding an E blade layer between the opener and mag/Phillips layers, still undecided on this.


-
The new stuff is so shiny.

As for the E blade layer idea, wowsers! :o
Am I right in assuming that the E blade is as thick as the can opener/bottle opener? Maybe you could have an extra bottle opener or some other tool opposite the E blade in your Champ X-Large?
-
-
Pabs, the can opener spring is too wide for the E blade, and I would have to add spacers and a back tool. The dual blade layer on the XLT also has a back tool which I don't want, so if I do add it I will use a saw spring which is the right width.

Thanks Mags, I am still undecided though, the whole feel of the thing would be different. :ahhh
I appreciate the interest all!

-
Layer 1 done, but not without trouble. The no keyring spring I had was from a knife made before the half stop in the bottle opener, so I had to find the right spring with no keyring and half stop. I had a Standard that worked, so that makes 7 disassemblies.
They changed the opener and spring again at some point, so the profiles are different and they don't interchange correctly. The top one is the one I couldn't use, and the bottom one is the new style which would not work either.The bottom photo is the first layer complete. I am cleaning up the liners and tools as I go with 0000 steel wool and the file on my Spirit to remove any burrs.



-
Blimey Twigs, this is going to the most expensive SAK EVER! :ahhh
-
Layer 2 went well, decided to forego the extra E blade layer, the old hoss is plenty capable as is.

Finally got that broken Phillips gone! The main reason I quit carrying it. :D

-
Does the bottle opener that you are using have the locking nub?
As I see it, Vic made 3 different rests:
The one for the bottle opener with the round tang.
The one for the bottle opener with the square tang, but no nub.
The one for the bottle opener with the square tang AND nub(the most recent) -
@Pablo O'Brien said:
Does the bottle opener that you are using have the locking nub?
As I see it, Vic made 3 different rests:
The one for the bottle opener with the round tang.
The one for the bottle opener with the square tang, but no nub.
The one for the bottle opener with the square tang AND nub(the most recent)No, it's the one in the middle in the above photo showing the 3 styles, minus the keyring. The one with the nub is the newest, but I'm not sure when the change happened. I think all the versions are available both with and without keyring attachment, but have not verified the newest ones, I don't know if they even offer a no keyring option these days on models with full opener layers.

-
Layer 3 done. The pliers joint is a little loose and the teeth are not as sharp anymore, but I wanted to keep the originals, after all it's what separates the SwissChamps from the Champions! :D I got a lot of use out of these pliers and in some pretty unconventional situations, so worn or not they are staying put to keep most of the integrity of the knife intact. Same with the main blade, it needed some sharpening, but I felt if I changed it, I wouldn't be able to say it's the same knife. Something like that anyway, dunno how many parts you can change and still preserve the identity of the original. Maybe overthinking this point.

The top photo shows how to get the springs to flex for assembly, put the tool and spring together at the top where the pins have some movement, and work the whole business down to the liner. trying to wrestle the tool onto the spring at the liner is pretty difficult, esp. with the thicker ones.



-
I prefer to drop the spring and tool down, then the next liner, before I "seat" and tension the tool on the spring with something like a mini screwdriver.
I find that omitting the liner can cause the pin stock to bend sometimes, but that may be due to incorrect technique.
-
Here's a shot of how cruddy the innards on these get after 5 or 6 years of daily use and only moderate maintenance, and then sitting for almost 20 years. :ahhh

-
@Pablo O'Brien said:
I prefer to drop the spring and tool down, then the next liner, before I "seat" and tension the tool on the spring with something like a mini screwdriver.
I find that omitting the liner can cause the pin stock to bend sometimes, but that may be due to incorrect technique.
I have done that on short pin mods, but working them down together is much easier if you have long enough pins.

-
This is brilliant Twigs! It looks like you are taking your time with the build and doing it nice and calmly.

Thanks for the pics.

-
Layer 4 done, new scissors, same old hook. Layer 4 1/2 was another slight problem, after I used some of the tools for mods, I tried to drill the rest of the pin out, and it was just the right size to snap off when it galled in the fish tool spring. I thought it would let go when I disassembled it, but noooooo... Vise grips didn't work, hammer didn't work, and I didn't want to try to drill it again. I had a spare so it will actually have 2 new springs (so far). :ahhh

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login