Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

Gerber MP600 DET knockoff 'Anti-explosion Plier' (Lynn's $5 MT Challenge)

Scheduled Pinned Locked Moved Cheap and Cheerful (or otherwise!)
26 Posts 1 Posters 6.4k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Lynn LeFeyL
    Lynn LeFeyL
    Lynn LeFey
    wrote on last edited by
    #7

    If you've read any of the other $5 challenge entries, you all know how this blade test goes.

    Out of the package, as received, it was JUST able to cut regular paper along it's plain edge portion.

    After sharpening, which just required 20 strokes on each side on ceramic rods, it was up to cleanly cutting thin receipt paper. I also used a diamond rod on the serrated protion, if for nothing else, to remove the PAINT from the cutting surface. :facepalm:

    Then, off to cut some cardboard...

    The good news here, I guess, is that the handles are very comfortable, and the lock on the blade works, and made me feel secure in hard use of the tool. The BAD news is that the serrated portion SHREDDED the material more than cut it, and unless I was extremely careful, the serrated portion of the blade was pretty certainly going to get involved.

    For those readers who know me, this is going to be no surprise...
    I HATE combination blades. I DEEPLY, from the bottom of my soul HATE them. They are the worst idea ever. Worse than that, the mechanics of the Gerber sliding head system already force the blades to be short in comparison to the tool's overall length. Then you go and screw up a blade by taking away half it's useful cutting surface for... for WHAT? A portion of blade that's rediculously hard to sharpen, and won't chew through 550 paracord?

    SMURF YOU, stupid blade makers! Die in a housefire! :rant:

    So... I'd LOVE to go try some whittling with this thing, but... yeah. It doesn't work for that. BECAUSE SOMEONE PUT SERRATIONS ON THE BLADE where I'd normally be choking up for fine work!

    :rant: :rant: :rant:

    This is not solely a function of THIS tool. I have an actual MP600, and it has a virtually identical blade design. And IT sucks, too.

    Blade for small tasks or mulching cardboard: reluctant PASS

    1 Reply Last reply
    0
    • Lynn LeFeyL
      Lynn LeFeyL
      Lynn LeFey
      wrote on last edited by
      #8

      @ThePeacent said:
      You can grab caterpillars safely applying minimal pressure on their thicker part with the james, and letting the soft squishy organs move frely inside the crimper's hole. Doesn't work for all sizes of caterpillars, though ๐Ÿ˜›

      I'm assuming you have METRIC caterpillars over there, and they wouldn't work as well with our English sized caterpillars. ๐Ÿ˜„

      1 Reply Last reply
      0
      • Lynn LeFeyL
        Lynn LeFeyL
        Lynn LeFey
        wrote on last edited by Lynn LeFey
        #9

        Test of screwdrivers

        Phillips
        I tried the phillips in a hinge screw, and it seemed REALLY solid. So I took it to THE test, the one no other tool in this challenge has yet faced. A woodscrew in a bench. I've broken multitools on these screws before. It's as far as I ever push tools in testing.

        And...?

        Success. It wanted to cam out of the screw, unless I applied considerable pressure, but the locking tools ALLOWED me to apply as much pressure as I wanted. Solid tool lock-up, solid performance. I'd like to see the head formed a little better, slot into screws more securely, but it did the job, along with about 6 other much less difficult screws.

        The flathead got to go against a paint-crusted screw in a latchplate.

        It did fine. One scrape of the flathead's blade against the old paint to clear a groove, and it turned the screw easily.

        On to the crusty paint can pry test.

        Maybe the most solid performance in this task so far in the challenge. This tool just generally feels like it's up to WAY more hard-work tasks than the others. The locking mechanism lends to some of that, but it's also really solidly constructed. 'Borrowing' a proven design helps, I'm sure.

        I actually didn't test the small flathead on the cap lifter, other than on a few very light screws, like faceplates of outlets and light switches. It's small enough that I don't think it'd ever be put to hard use.

        Drivers: PASS with distinction

        1 Reply Last reply
        0
        • gerleatherbermanG
          gerleatherbermanG
          gerleatherberman
          wrote on last edited by
          #10

          Nice write-up, Lynn! :like:

          The steel on the tools is no joke. I had a 600 with a broken file and blade. Tried to drill the fake DET holes open to fit the larger Gerber pins and burned up several expensive bits. ๐Ÿ˜ฎ

          One cheater trick is to take the clips off that hold the pliers in and put a tiny washer around the lower clip-peg and re-install the pliers. This will make the plier tips actually meet. Did that today to mine and the pliers meet. What did I gain from that? An Anti-Explosion" POS with slightly more aligned pliers. :rofl:

          1 Reply Last reply
          0
          • Lynn LeFeyL
            Lynn LeFeyL
            Lynn LeFey
            wrote on last edited by Lynn LeFey
            #11

            @gerleatherberman said:
            One cheater trick is to take the clips off that hold the pliers in and put a tiny washer around the lower clip-peg and re-install the pliers. This will make the plier tips actually meet. Did that today to mine and the pliers meet. What did I gain from that? An Anti-Explosion" POS with slightly more aligned pliers. :rofl:

            Great tip! Thanks! :salute:

            This would probably drastically improve my opinion of the pliers.

            On to cap lifter and can opener.

            For cap lifting...

            Success. It's a little... okay, maybe more than a LITTLE awkward at this task, but it succeeded.

            Can opener?

            Mmmm... No. The nearest the blade can get to the rim of the can is seen here where it dented the lid. I'm not going to bother mangling a can, trying to get it open. There's nothing inherently wrong with the can opener itself, it's just in the wrong PLACE on the tool. There's no reason it couldn't be moved into a more left-side (as viewed in the photo) position, making it hook the rim without the body of the tool being in the way. The fail here is 100% from idiots assembling the tool in a stupid way.

            Just... :facepalm:

            I've had like three or four MTs like this. Just assembled by idiots, apparently.

            And I don't feel like spending a single second more on this tool than I have to. I'm NOT taking it apart and fixing this stupid error. I did this fix on the Northern Tools 'Mountain' multitool, in this thread.
            </topic/44010

            And I had a pretty detailed review of how to disassemble and reassemble an MP600 in 'My bargain basement ebay MP600 purchase' thread here...
            </post/827315>

            That will get you in the ballpark if you want an idea of how fixing the tool would go. A word of warning before you begin, if you decide to try 'cheap and cheerful surgery' on this: TAKE PICTURES, so you know how the parts went in before you began.

            Cap Lifter: moderate PASS
            Can Opener: FAIL in stock configuration

            1 Reply Last reply
            0
            • Lynn LeFeyL
              Lynn LeFeyL
              Lynn LeFey
              wrote on last edited by Lynn LeFey
              #12

              So, there are TWO functions on this MT that are remnants of copying the MP600 DET. There's the cap crimper in the plier head, and...

              This...

              That's a spike, intended to punch holes in blocks of c4, so you can then insert the blast cap you crimped earlier with the pliers.

              I said in the plier review that I thought the cap crimper would be the least used tool I've seen on an MT, and I stand by that. This spike, while it would never see use for demolitions, MIGHT be useful as a marlin spike.It worked okay in picking apart a knot in some 550 paracord.

              I've made a lot of little woodburning cook stoves from tin cans that require a lot of vent holes to be punched. This thing easily punches through cans for that function.

              I've half-jokingly referred to various otherwise useless tools as 'general pokey bits of metal'. Well, this is a specifically designed pokey bit of metal, and it's a REALLY good poker.

              Lockup on my version was solid, and it would take extraordinary side pressure to tear it out of that locked position, I pressed on it with maybe 30 lbs of force, and it felt like if I WANTED to make it collapse, I could get it to, but at that point it seemed way beyond any real-world use. A downward stabbing kind of thrust with this thing into something at a full swing MIGHT be able to produce that kind of force.

              Spike for spiking things that need to be spiked: PASS

              1 Reply Last reply
              0
              • Lynn LeFeyL
                Lynn LeFeyL
                Lynn LeFey
                wrote on last edited by
                #13

                Okay, some thoughts to wrap up.

                This tool is 225g (about 8oz) where another plier based competitor, the Ozark Trail 12-in-1 tool is 161g (a bit over 5 1/2 oz)

                That's not a small difference. The DET knockoff is capable of more HEAVY work, but fails in some really basic functions. The plier fail is a BIG issue. I'll have to see if i can get some thin brass washers to improve them. If not, I'd almost call this thing a straight up fail. The two BIG functions, pliers and knife, don't stack up to the Ozark Trail tool.

                If I were stuck with this tool, I'd reprofile that blade, to get rid of the BS semi-serrated crap, to make that blade USEFUL, shim up the pliers, and... honestly... this would probably be a really good medium duty tool. Oh, right... and take it apart to move the can opener. That's starting to seem like a lot of work for a cheap tool, to make it 'tolerable'.

                I can't knock it out of the competition yet, but as it comes it's not as good as the Ozark Trail 12-in-1 tool, IMO.

                1 Reply Last reply
                0
                • ReamerPunchR
                  ReamerPunchR
                  ReamerPunch
                  Global Moderators
                  wrote on last edited by
                  #14

                  Having a big tool like that might give it an edge over the keychain ones in the competition, but then again, if it's this bad, I won't hold my breath. :salute:

                  1 Reply Last reply
                  0
                  • Sam LimS
                    Sam LimS
                    Sam Lim
                    wrote on last edited by
                    #15

                    I have got one of this. This is a very common MT from where I am. Sadly, most people know they are Chinese knock offs but they doesn't seems to care.. To me, it's good for one thing. The cloning of this tool is rather good. Parts are even almost 1 : 1 ratio. I scrutinised the plastic lock tab to fix my mp600. It fits almost perfectly. Yes, the file is quite decent as well.

                    1 Reply Last reply
                    0
                    • ThePeacentT
                      ThePeacentT
                      ThePeacent
                      wrote on last edited by
                      #16

                      good thoughts and most I share.
                      The drivers are good and they've proven sturdy to me, but as I said I felt the need to remove the paint on mine so they could fit my most commonly found screws. The can opener was especially bad in that regard :facepalm:

                      My spike failed but I admit it was after applying excessive force and twisting in both directions, during the previous year of poking and stabbing it never failed once. :salute:
                      No comments on the lanyard function, that horrendous and badly implemented thing?

                      1 Reply Last reply
                      0
                      • gerleatherbermanG
                        gerleatherbermanG
                        gerleatherberman
                        wrote on last edited by gerleatherberman
                        #17

                        Thank you for the excellent work, Lynn! Very cool stuff, since I never use a can opener, I never knew how terribly it was placed!
                        As Sam Lim said, the tool overall is close to the real thing sort of, except the tool pivots are much smaller around and poorly fashioned compared to Gerber and a few other things. This makes tool swapping difficult. You cannot install Gerber tools into the handles, and you have to drill the hole in the fake's tools bigger to fit a Gerber. I did manage to get the file(removed from older det fake with broke parts. Not my new one) drilled out bigger for another MP600BN I use as a beater and it works great, but I burned up some expensive bits doing it. Not worth the time or money to swap handle tools over. The fake DET steel is also notably softer and more poorly stamped as well. The lock slides lift off nearly a 1/4" when you pull back on them. This tool looks and acts like a Gerber, but in the end, would never last as long as a real MP600. Sorry Sam. :pok:

                        Now, with that being said, I was able to salvage something out of mine with something I picked up for a few bucks a while back
                        What is it? Only the easiest way to make this tool useful. ๐Ÿ˜„
                        Boom. 1..2..3.. real Gerber plier head fits perfectly :multi:

                        20171229_070150-1.jpg

                        20171229_070336-1.jpeg

                        20171229_070541-1.jpeg

                        1 Reply Last reply
                        0
                        • Lynn LeFeyL
                          Lynn LeFeyL
                          Lynn LeFey
                          wrote on last edited by
                          #18

                          I wondered about that myself. Having disassembled the MP600 I have (that was itself a beater), I considered trying a plier head swap to the fake with a genuine Gerber one. It's not that hard to slide those clips off.

                          Then I remembered.... there is NOTHING in the fake that works better than in the genuine one, so why bother? Still if you have the spare head lying around, or in my opinion a better option, a plier head without the Crimper (as you've done).

                          THEN... then this tool would be pretty serviceable.

                          1 Reply Last reply
                          0
                          • gerleatherbermanG
                            gerleatherbermanG
                            gerleatherberman
                            wrote on last edited by
                            #19

                            @Lynn LeFey said:
                            I wondered about that myself. Having disassembled the MP600 I have (that was itself a beater), I considered trying a plier head swap to the fake with a genuine Gerber one. It's not that hard to slide those clips off.

                            Then I remembered.... there is NOTHING in the fake that works better than in the genuine one, so why bother? Still if you have the spare head lying around, or in my opinion a better option, a plier head without the Crimper (as you've done).

                            THEN... then this tool would be pretty serviceable.

                            Indeed I had a spare plier head laying around. Kind of a neat tool, but mainly a toy more than a real 600. :rofl:

                            1 Reply Last reply
                            0
                            • Sam LimS
                              Sam LimS
                              Sam Lim
                              wrote on last edited by
                              #20

                              There. I got the Mp600 frame with one side of the lock gone. Used the fake to replace the missing lock. Works perfectly. Left is the original lock tab, right is the transplant from the fake.. The original was riveted. I have to use screw and nut, but it works. See how similar in size the cloned parts are.

                              IMG_20171230_232149-744x992.jpg

                              IMG_20171230_231845-744x992.jpg

                              1 Reply Last reply
                              0
                              • Lynn LeFeyL
                                Lynn LeFeyL
                                Lynn LeFey
                                wrote on last edited by
                                #21

                                Nice! :tu:

                                I thought I'd used this picture in the write-up, but I didn't. I have an actual Gerber MP600, and compared the two VERY closely.

                                It's good to know the knockoff is at least worth a couple donor parts.

                                1 Reply Last reply
                                0
                                • Don PabloD
                                  Don PabloD
                                  Don Pablo
                                  wrote on last edited by
                                  #22

                                  Spoiler:
                                  The ship wherein Theseus and the youth of Athens returned from Crete had thirty oars, and was preserved by the Athenians down even to the time of Demetrius Phalereus, for they took away the old planks as they decayed, putting in new and stronger timber in their places, in so much that this ship became a standing example among the philosophers, for the logical question of things that grow; one side holding that the ship remained the same, and the other contending that it was not the same.

                                  โ€”โ€‰Plutarch, Theseus

                                  Spoiler:
                                  So if you gradually replace the real MP600 parts with parts from the fake one, when is it no longer a real MP600? ๐Ÿ˜„

                                  1 Reply Last reply
                                  0
                                  • gerleatherbermanG
                                    gerleatherbermanG
                                    gerleatherberman
                                    wrote on last edited by
                                    #23

                                    @Pablo O'Brien said:

                                    Spoiler:
                                    The ship wherein Theseus and the youth of Athens returned from Crete had thirty oars, and was preserved by the Athenians down even to the time of Demetrius Phalereus, for they took away the old planks as they decayed, putting in new and stronger timber in their places, in so much that this ship became a standing example among the philosophers, for the logical question of things that grow; one side holding that the ship remained the same, and the other contending that it was not the same.

                                    โ€”โ€‰Plutarch, Theseus

                                    Spoiler:
                                    So if you gradually replace the real MP600 parts with parts from the fake one, when is it no longer a real MP600? ๐Ÿ˜„

                                    OR. Since Gerber just assembles the 600 in the US, and presumably the parts are made overseas, do the knock-off parts become Gerber parts when installed into the MP600?

                                    Note: I am no philosopher(or study thereof), but I do like multi-tools. And that was a great philosophical quagmire to contemplate that you quoted, Pablo. Thank you! ๐Ÿ‘

                                    1 Reply Last reply
                                    0
                                    • Lynn LeFeyL
                                      Lynn LeFeyL
                                      Lynn LeFey
                                      wrote on last edited by
                                      #24

                                      I don't think I linked it before, but here's Chako's great comparison of this tool versus a real Gerber to help spot it as a fake.
                                      </topic/18527

                                      1 Reply Last reply
                                      0
                                      • ThePeacentT
                                        ThePeacentT
                                        ThePeacent
                                        wrote on last edited by
                                        #25

                                        to add to this excellent overview, I decided to put a side pic with other cheapos and a good SAK PX in ase anyone in the future wants to have a size/looks reference when considering buying this tool :tu:

                                        hopefully you don't mind Lynn, I took the pics today and considered it possibly useful information to add to the archives of this great forum :salute:

                                        I'll edit it out if it is not the place

                                        1 Reply Last reply
                                        0
                                        • Lynn LeFeyL
                                          Lynn LeFeyL
                                          Lynn LeFey
                                          wrote on last edited by
                                          #26

                                          Seems like a fine place for it to me. :tu:

                                          Yeah... if this thing had regular pliers instead of the cap crimper nonsense, I don't think it'd be bad at $5-10 price range.

                                          1 Reply Last reply
                                          0

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better ๐Ÿ’—

                                          Register Login

                                          • Login

                                          • Don't have an account? Register

                                          • First post
                                            Last post
                                          0
                                          • Categories
                                          • Recent
                                          • Popular
                                          • World