Gerber MP600 DET knockoff 'Anti-explosion Plier' (Lynn's $5 MT Challenge)
-
@ThePeacent said:
You can grab caterpillars safely applying minimal pressure on their thicker part with the james, and letting the soft squishy organs move frely inside the crimper's hole. Doesn't work for all sizes of caterpillars, though
I'm assuming you have METRIC caterpillars over there, and they wouldn't work as well with our English sized caterpillars.

-
Test of screwdrivers
Phillips
I tried the phillips in a hinge screw, and it seemed REALLY solid. So I took it to THE test, the one no other tool in this challenge has yet faced. A woodscrew in a bench. I've broken multitools on these screws before. It's as far as I ever push tools in testing.Success. It wanted to cam out of the screw, unless I applied considerable pressure, but the locking tools ALLOWED me to apply as much pressure as I wanted. Solid tool lock-up, solid performance. I'd like to see the head formed a little better, slot into screws more securely, but it did the job, along with about 6 other much less difficult screws.
The flathead got to go against a paint-crusted screw in a latchplate.

It did fine. One scrape of the flathead's blade against the old paint to clear a groove, and it turned the screw easily.
On to the crusty paint can pry test.

Maybe the most solid performance in this task so far in the challenge. This tool just generally feels like it's up to WAY more hard-work tasks than the others. The locking mechanism lends to some of that, but it's also really solidly constructed. 'Borrowing' a proven design helps, I'm sure.
I actually didn't test the small flathead on the cap lifter, other than on a few very light screws, like faceplates of outlets and light switches. It's small enough that I don't think it'd ever be put to hard use.
Drivers: PASS with distinction
-
Nice write-up, Lynn!

The steel on the tools is no joke. I had a 600 with a broken file and blade. Tried to drill the fake DET holes open to fit the larger Gerber pins and burned up several expensive bits.

One cheater trick is to take the clips off that hold the pliers in and put a tiny washer around the lower clip-peg and re-install the pliers. This will make the plier tips actually meet. Did that today to mine and the pliers meet. What did I gain from that? An Anti-Explosion" POS with slightly more aligned pliers.

-
@gerleatherberman said:
One cheater trick is to take the clips off that hold the pliers in and put a tiny washer around the lower clip-peg and re-install the pliers. This will make the plier tips actually meet. Did that today to mine and the pliers meet. What did I gain from that? An Anti-Explosion" POS with slightly more aligned pliers.
Great tip! Thanks!

This would probably drastically improve my opinion of the pliers.
On to cap lifter and can opener.
Success. It's a little... okay, maybe more than a LITTLE awkward at this task, but it succeeded.
Mmmm... No. The nearest the blade can get to the rim of the can is seen here where it dented the lid. I'm not going to bother mangling a can, trying to get it open. There's nothing inherently wrong with the can opener itself, it's just in the wrong PLACE on the tool. There's no reason it couldn't be moved into a more left-side (as viewed in the photo) position, making it hook the rim without the body of the tool being in the way. The fail here is 100% from idiots assembling the tool in a stupid way.
Just...

I've had like three or four MTs like this. Just assembled by idiots, apparently.
And I don't feel like spending a single second more on this tool than I have to. I'm NOT taking it apart and fixing this stupid error. I did this fix on the Northern Tools 'Mountain' multitool, in this thread.
</topic/44010And I had a pretty detailed review of how to disassemble and reassemble an MP600 in 'My bargain basement ebay MP600 purchase' thread here...
</post/827315>That will get you in the ballpark if you want an idea of how fixing the tool would go. A word of warning before you begin, if you decide to try 'cheap and cheerful surgery' on this: TAKE PICTURES, so you know how the parts went in before you began.
Cap Lifter: moderate PASS
Can Opener: FAIL in stock configuration -
So, there are TWO functions on this MT that are remnants of copying the MP600 DET. There's the cap crimper in the plier head, and...
That's a spike, intended to punch holes in blocks of c4, so you can then insert the blast cap you crimped earlier with the pliers.
I said in the plier review that I thought the cap crimper would be the least used tool I've seen on an MT, and I stand by that. This spike, while it would never see use for demolitions, MIGHT be useful as a marlin spike.It worked okay in picking apart a knot in some 550 paracord.
I've made a lot of little woodburning cook stoves from tin cans that require a lot of vent holes to be punched. This thing easily punches through cans for that function.
I've half-jokingly referred to various otherwise useless tools as 'general pokey bits of metal'. Well, this is a specifically designed pokey bit of metal, and it's a REALLY good poker.
Lockup on my version was solid, and it would take extraordinary side pressure to tear it out of that locked position, I pressed on it with maybe 30 lbs of force, and it felt like if I WANTED to make it collapse, I could get it to, but at that point it seemed way beyond any real-world use. A downward stabbing kind of thrust with this thing into something at a full swing MIGHT be able to produce that kind of force.
Spike for spiking things that need to be spiked: PASS
-
Okay, some thoughts to wrap up.
This tool is 225g (about 8oz) where another plier based competitor, the Ozark Trail 12-in-1 tool is 161g (a bit over 5 1/2 oz)
That's not a small difference. The DET knockoff is capable of more HEAVY work, but fails in some really basic functions. The plier fail is a BIG issue. I'll have to see if i can get some thin brass washers to improve them. If not, I'd almost call this thing a straight up fail. The two BIG functions, pliers and knife, don't stack up to the Ozark Trail tool.
If I were stuck with this tool, I'd reprofile that blade, to get rid of the BS semi-serrated crap, to make that blade USEFUL, shim up the pliers, and... honestly... this would probably be a really good medium duty tool. Oh, right... and take it apart to move the can opener. That's starting to seem like a lot of work for a cheap tool, to make it 'tolerable'.
I can't knock it out of the competition yet, but as it comes it's not as good as the Ozark Trail 12-in-1 tool, IMO.
-
Having a big tool like that might give it an edge over the keychain ones in the competition, but then again, if it's this bad, I won't hold my breath.

-
I have got one of this. This is a very common MT from where I am. Sadly, most people know they are Chinese knock offs but they doesn't seems to care.. To me, it's good for one thing. The cloning of this tool is rather good. Parts are even almost 1 : 1 ratio. I scrutinised the plastic lock tab to fix my mp600. It fits almost perfectly. Yes, the file is quite decent as well.
-
good thoughts and most I share.
The drivers are good and they've proven sturdy to me, but as I said I felt the need to remove the paint on mine so they could fit my most commonly found screws. The can opener was especially bad in that regard

My spike failed but I admit it was after applying excessive force and twisting in both directions, during the previous year of poking and stabbing it never failed once.

No comments on the lanyard function, that horrendous and badly implemented thing? -
Thank you for the excellent work, Lynn! Very cool stuff, since I never use a can opener, I never knew how terribly it was placed!
As Sam Lim said, the tool overall is close to the real thing sort of, except the tool pivots are much smaller around and poorly fashioned compared to Gerber and a few other things. This makes tool swapping difficult. You cannot install Gerber tools into the handles, and you have to drill the hole in the fake's tools bigger to fit a Gerber. I did manage to get the file(removed from older det fake with broke parts. Not my new one) drilled out bigger for another MP600BN I use as a beater and it works great, but I burned up some expensive bits doing it. Not worth the time or money to swap handle tools over. The fake DET steel is also notably softer and more poorly stamped as well. The lock slides lift off nearly a 1/4" when you pull back on them. This tool looks and acts like a Gerber, but in the end, would never last as long as a real MP600. Sorry Sam.
Now, with that being said, I was able to salvage something out of mine with something I picked up for a few bucks a while back
What is it? Only the easiest way to make this tool useful.
Boom. 1..2..3.. real Gerber plier head fits perfectly



-
I wondered about that myself. Having disassembled the MP600 I have (that was itself a beater), I considered trying a plier head swap to the fake with a genuine Gerber one. It's not that hard to slide those clips off.
Then I remembered.... there is NOTHING in the fake that works better than in the genuine one, so why bother? Still if you have the spare head lying around, or in my opinion a better option, a plier head without the Crimper (as you've done).
THEN... then this tool would be pretty serviceable.
-
@Lynn LeFey said:
I wondered about that myself. Having disassembled the MP600 I have (that was itself a beater), I considered trying a plier head swap to the fake with a genuine Gerber one. It's not that hard to slide those clips off.Then I remembered.... there is NOTHING in the fake that works better than in the genuine one, so why bother? Still if you have the spare head lying around, or in my opinion a better option, a plier head without the Crimper (as you've done).
THEN... then this tool would be pretty serviceable.
Indeed I had a spare plier head laying around. Kind of a neat tool, but mainly a toy more than a real 600.

-
There. I got the Mp600 frame with one side of the lock gone. Used the fake to replace the missing lock. Works perfectly. Left is the original lock tab, right is the transplant from the fake.. The original was riveted. I have to use screw and nut, but it works. See how similar in size the cloned parts are.


-
-
Spoiler:
The ship wherein Theseus and the youth of Athens returned from Crete had thirty oars, and was preserved by the Athenians down even to the time of Demetrius Phalereus, for they took away the old planks as they decayed, putting in new and stronger timber in their places, in so much that this ship became a standing example among the philosophers, for the logical question of things that grow; one side holding that the ship remained the same, and the other contending that it was not the same.โโPlutarch, Theseus
Spoiler:
So if you gradually replace the real MP600 parts with parts from the fake one, when is it no longer a real MP600?
-
@Pablo O'Brien said:
Spoiler:
The ship wherein Theseus and the youth of Athens returned from Crete had thirty oars, and was preserved by the Athenians down even to the time of Demetrius Phalereus, for they took away the old planks as they decayed, putting in new and stronger timber in their places, in so much that this ship became a standing example among the philosophers, for the logical question of things that grow; one side holding that the ship remained the same, and the other contending that it was not the same.โโPlutarch, Theseus
Spoiler:
So if you gradually replace the real MP600 parts with parts from the fake one, when is it no longer a real MP600?
OR. Since Gerber just assembles the 600 in the US, and presumably the parts are made overseas, do the knock-off parts become Gerber parts when installed into the MP600?
Note: I am no philosopher(or study thereof), but I do like multi-tools. And that was a great philosophical quagmire to contemplate that you quoted, Pablo. Thank you!

-
I don't think I linked it before, but here's Chako's great comparison of this tool versus a real Gerber to help spot it as a fake.
</topic/18527 -
to add to this excellent overview, I decided to put a side pic with other cheapos and a good SAK PX in ase anyone in the future wants to have a size/looks reference when considering buying this tool


hopefully you don't mind Lynn, I took the pics today and considered it possibly useful information to add to the archives of this great forum


I'll edit it out if it is not the place
-
Seems like a fine place for it to me.

Yeah... if this thing had regular pliers instead of the cap crimper nonsense, I don't think it'd be bad at $5-10 price range.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better ๐
Register Login



