Spirit 30 day Challenge with a few Early- early Birds
-
I just have one question: what’s a SPIRT CALLENGE?

Maybe Poncho can fix the typos in the thread title

First off I am not a typist, second I had to rush setting this up. My wonderful Wife got us tickets for the drive in theater and I was running late getting home from work. Thanks for understanding and Great first shots guys. Way to get us started.

-
For the early birds, 30th is day 00 and 31st is day 1?

Or is 1st of January day 1?
I wouldn't mind starting tomorrow. -
@ReamerPunch said:
For the early birds, 30th is day 00 and 31st is day 1?
Or is 1st of January day 1?
I wouldn't mind starting tomorrow.As i understand it the 31st will be day one for the Early-birds.
The 10th will be day one for the rest of us. Hopefully I won't be the only one, it's allways more fun to celebrate my birthday with others.
-
1227171432a by Poncho 65, on FlickrAlready put it to work tightening a loose screw in a door knob in the house

1229171906 by Poncho 65, on FlickrAlso I am happy to report that the LM bit adapter fits the Phillips of the Spirit
Mine is apparently an XC according to jaya_man :D
1229171907 by Poncho 65, on FlickrPoncho, give that adaptor a work out for me. It may be just what I've been looking for, I can't wait to hear more about it.
-
Ok, I'll snap a pic of the Spirit, just to enter today, as day 0, and join on the 31st.

The cylindrical adapters that fit the Rebar etc do fit the Spirit Phillips, and the Explored/SwissChamp one, but a square shank Phillips is stronger, since you apply force with the square neck, instead of the Phillips tynes.
Spoiler:

It also fits the medium flathead on the Sideclip, though not perfectly. No spinning, but a lot of room to wiggle from side to side.
Spoiler:

It also fits the PST Phillips, if you also have the small flathead deployed, so the adapter does not spin.
Same with the medium flathead and awl on the other handle.Spoiler:

Spoiler:

-
Day 0.


-
Early bird repost:
Day 0 I guess?
-
Great pics already guys

and could you get some more pics of the cylinfdrical adapter RP
Some views of the end the tool goes in please 
On a side note, I never try to overtorque the driver with the adapter on
If it has to be used that hard then it is time to try and track a more dedicated tool down 
-
I just have one question: what’s a SPIRT CALLENGE?

Maybe Poncho can fix the typos in the thread title

First off I am not a typist, second I had to rush setting this up. My wonderful Wife got us tickets for the drive in theater and I was running late getting home from work. Thanks for understanding and Great first shots guys. Way to get us started.

No harm done I hope! I figured you were rushed; since all of this came about quickly yesterday. But here we are roaring to go.
Where does one get those bit adapters ? Like poncho’s or reamer’s.
-
@ReamerPunch said:
For the early birds, 30th is day 00 and 31st is day 1?
Or is 1st of January day 1?
I wouldn't mind starting tomorrow.It looks like the early birds are off to a staggered start. Poncho and I started yesterday and some start today.
-
As depicted by the picture, the needle nose are great. This morning I was attempting to tighten a size #2 brass screw, and as most of us knows, it snapped. Had to drill around the screw hole to extract the tiny broken threaded end left in the wood stock. I used my Spirit needle nose to grab that little smurf. I applied enough pressure on the handles to secure the jaws on the little smurf and half a turn with my wrist...It came out. I was very pleased.
Drilled out the messy hole and inserted a piece of dowel to make the hole strong again...
First task of removing broken screw was a success.Spirit needle nose plier jaws: 1
Busted little brass screw imbedded 3/8th of an inch into birds eye maple: 0
-
@Marc_in_NS said:
As depicted by the picture, the needle nose are great. This morning I was attempting to tighten a size #2 brass screw, and as most of us knows, it snapped. Had to drill around the screw hole to extract the tiny broken threaded end left in the wood stock. I used my Spirit needle nose to grab that little smurf. I applied enough pressure on the handles to secure the jaws on the little smurf and half a turn with my wrist...It came out. I was very pleased.
Drilled out the messy hole and inserted a piece of dowel to make the hole strong again...
First task of removing broken screw was a success.Spirit needle nose plier jaws: 1
Busted little brass screw imbedded 3/8th of an inch into birds eye maple: 0

-
Day 2

Tested out the wire cutters on some old rca cable
Worked pretty well but didn't cut the fine wire cleanly every time.



-
Sorry guys, I have to withdraw from this challenge for personal reasons. I wish you all a good time during this gruelling challenge. I shall also leave this wonderful community. It’s been very interesting, to say the least, to have met you good folks.
So long!
-
@Marc_in_NS said:
Sorry guys, I have to withdraw from this challenge for personal reasons. I wish you all a good time during this gruelling challenge. I shall also leave this wonderful community. It’s been very interesting, to say the least, to have met you good folks.So long!
Wait what?!
You're leaving us?!
:'( :'( :'(
If you find your way back here, there will be a seat open for you...
I wish you all the best and hope that there isn't any bad news involved in this...I'll miss you buddy...I really will :'(
-
Having that said...
Day 1, quite reluctant since Marc's news... couldn't be sadder at the moment.Mounted an electrical heater that I removed prior to the office renovations. It's an older model that came with the house.

-
Wow Marc, that was sudden :(
Sorry to see you go and I hope it's nothing serious. We will be here if you decide to come back and I hope you do

All the best

-
@Poncho65 said:
Great pics already guys

and could you get some more pics of the cylinfdrical adapter RP
Some views of the end the tool goes in please 
On a side note, I never try to overtorque the driver with the adapter on
If it has to be used that hard then it is time to try and track a more dedicated tool down 
Out of daylight, but I'll post more tomorrow.

-
Wow Marc :ahhh don't go :ahhh But if you must I hope you can come back quickly buddy

Really gonna miss you in the challenge :-\
-
Great pics already guys

and could you get some more pics of the cylinfdrical adapter RP
Some views of the end the tool goes in please 
On a side note, I never try to overtorque the driver with the adapter on
If it has to be used that hard then it is time to try and track a more dedicated tool down 
Out of daylight, but I'll post more tomorrow.

Thanks RP
Can't wait 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login