Too Sharp?
-
I've tried polished edges, it does make the edge look shinny 8) but I gave it up pretty quick. The edge didn't seem to hold up as well for cardboard, wood, zip ties or other hard or abrasive cuts.
Yeah that’s what was stopping me from doing this before. Nice to know there are real world experiences in this. I guess I’ll see what happens with my Cold Steel. Hopefully the edge won’t roll too bad.
A polished edge should not roll any more than a toothier edge at the same angle.
If you make the edge angle too acute then steels like AUS-8 will roll and steels like S30V will micro chip.Good to know!!!
-
@pomsbz said:
My benchmark is to smoothly and slowly push cut receipt paper. If it can do that it can slice through food packaging without ripping it.Don’t laugh, but I rushed over to the kitchen to look for receipts. Lol.
Looks good! I wish I have access to a better camera and show some pics.
I have noticed that I could never get the edge next to the heel as sharp as the belly edge as the American Lawman doesn’t have a sharpening notch.
So when I slice something from beginning to end it’s always a bit tougher at first then smooths out at the end.
At this sharpening rate though eventually that heel will eventually disappear. My only niggling complaint on this wonderful knife.
As a side note when they came out with the same model but CTS XHP steel I immediately bought it in case my old one gets lost. But after a few days I shelved it. For some reason I really love the AUS 8. Very forgiving when I need to fix the edge.
I notched the blade one time accidentally cutting through some sheeting and cut into a rock. Took me only 10 minutes to fix.
In the Massdrop site I waxed poetically about budget steels and mentioned innocently that the super or high end steels were not as forgiving to sharpen and got slammed on my sharpening skills as a response. Hatahhhs!!!!
Gotta love social media.

-
@Pablo O'Brien said:
Hey, at least you won't feel the cuts due to them being sooo fine. :DMy neighbor and close friend borrowed a kitchen knife from us and when she returned it, placed it on our magnetic knife holder right next to the sharpest polished kitchen knife we own. We then sat down together for a beer when she noticed that the side of her hand was bleeding. She swore that her hand never came in contact with the other knife and from what I saw it didn't look like she did. That gets into the realm of scary sharp :D
-
@Pablo O'Brien said:
Hey, at least you won't feel the cuts due to them being sooo fine. :D
My neighbor and close friend borrowed a kitchen knife from us and when she returned it, placed it on our magnetic knife holder right next to the sharpest polished kitchen knife we own. We then sat down together for a beer when she noticed that the side of her hand was bleeding. She swore that her hand never came in contact with the other knife and from what I saw it didn't look like she did. That gets into the realm of scary sharp :D
has happened me on occasion with factory edged knives from Cold Steel and Spyderco.
Embarrassing but makes you :o at your new acquisition -
So after giving the new edge a test drive I’m thinking of keeping it this way. Biggest reason is that my wife was going through her purse collection 🤣 and I noticed that some of the stuff she was throwing away actually had some nice size clips I can use a carabiners. Nice brass rings too that I can repurpose.
I’m constantly using carabiners for something or the other and the ones she had on her purses were made of sturdier stuff.
Anyway the knife went through leather like cutting mud. Nice!! For sturdier material I noticed that as long as I cut firmly and slowly like popping zip ties the edge seems to hold up. Anything faster or harder seems like the edge needs touch up.
Off topic, but I wish that the crowd in Massdrop is as nice as the folks here. I give Grant and the other moderators kudos for maintaining a kind culture.
Massdrop has some great deals on knives and such but seem to attract trolls and steel snobs. I realize that AUS8 is a budget steel but when done right it has its place.
I never learn, but I’ll leave a comment on budget steels and I get trashed for some reason or the other.I mean I get it, we live in a life of embarrassing riches and better knife steels. But there are a few folks who love the old school back locks and don’t need adamantium claws for EDC 😜
Anyway, sorry for the rant. Thanks everyone for their responses!!
-
@OldBoy2016 said:
So after giving the new edge a test drive I’m thinking of keeping it this way. Biggest reason is that my wife was going through her purse collection 🤣 and I noticed that some of the stuff she was throwing away actually had some nice size clips I can use a carabiners. Nice brass rings too that I can repurpose.I’m constantly using carabiners for something or the other and the ones she had on her purses were made of sturdier stuff.
Anyway the knife went through leather like cutting mud. Nice!! For sturdier material I noticed that as long as I cut firmly and slowly like popping zip ties the edge seems to hold up. Anything faster or harder seems like the edge needs touch up.
Off topic, but I wish that the crowd in Massdrop is as nice as the folks here. I give Grant and the other moderators kudos for maintaining a kind culture.
Massdrop has some great deals on knives and such but seem to attract trolls and steel snobs. I realize that AUS8 is a budget steel but when done right it has its place.
I never learn, but I’ll leave a comment on budget steels and I get trashed for some reason or the other.I mean I get it, we live in a life of embarrassing riches and better knife steels. But there are a few folks who love the old school back locks and don’t need adamantium claws for EDC 😜
Anyway, sorry for the rant. Thanks everyone for their responses!!
AUS8 and 420HC are two of my favorites even after using and owning knives in ELMAX, CTS-XHP, S30V, etc.
in fact AUS8-A is the steel I have more folders with (about 22)
Just too good for everyday use and ease of sharpening
-
My favorite super steel is ordinary Vic steel.

-
So after giving the new edge a test drive I’m thinking of keeping it this way. Biggest reason is that my wife was going through her purse collection 🤣 and I noticed that some of the stuff she was throwing away actually had some nice size clips I can use a carabiners. Nice brass rings too that I can repurpose.
I’m constantly using carabiners for something or the other and the ones she had on her purses were made of sturdier stuff.
Anyway the knife went through leather like cutting mud. Nice!! For sturdier material I noticed that as long as I cut firmly and slowly like popping zip ties the edge seems to hold up. Anything faster or harder seems like the edge needs touch up.
Off topic, but I wish that the crowd in Massdrop is as nice as the folks here. I give Grant and the other moderators kudos for maintaining a kind culture.
Massdrop has some great deals on knives and such but seem to attract trolls and steel snobs. I realize that AUS8 is a budget steel but when done right it has its place.
I never learn, but I’ll leave a comment on budget steels and I get trashed for some reason or the other.I mean I get it, we live in a life of embarrassing riches and better knife steels. But there are a few folks who love the old school back locks and don’t need adamantium claws for EDC 😜
Anyway, sorry for the rant. Thanks everyone for their responses!!
AUS8 and 420HC are two of my favorites even after using and owning knives in ELMAX, CTS-XHP, S30V, etc.
in fact AUS8-A is the steel I have more folders with (about 22)
Just too good for everyday use and ease of sharpening
Thank you Peacant! I really enjoy aus8 and 420hc as well. Anything harder and it seems the blades chip more easily! A lot of people on MT.o trash talk 420hc, but when I hit a staple and roll an edge cutting a box open, it is nice to know I won't be spending all night putting a clean edge back on it.
-
I'm not sure I agree, "a lot of MTO folks trash talk 420HC". Could be I'm not reading those posts
. What I will say is, who the smurf cares what others preferences are when it comes to steel. Use what works for you and sharpen to the level you find works best. I think we all can agree that the manufacturer needs to heat treat the steel properly. As long as this is done then whatever steel is used it will be at its best.I have a variety of steels and what I find neat is many of us along with our super steel blades carry a SAK. I even see those with really expensive blades carry a SAK. You'd think if someone was a steel snob they'd not carry any steel other than a super steel. I also find it interesting that those same folks carry a MT. While LM has a MT with S30V there aren't a lot of super steel MTs.
I've personally never had any issues getting my Waves blade just like I like. I carry a 1095HC fixed blade for work as well and same goes for it. Both perform wonderfully and both are well used.
-
@Pablo O'Brien said:
I'm not sure I agree, "a lot of MTO folks trash talk 420HC". Could be I'm not reading those posts
.+1.

that also made me ???
in this forum precisely you see a love and appreciation for Gerber, Leatherman and Buck's 420 and for Victorinox steel that you never see on other forums. :ahhh
Compared to MT.org, Spyderco forums or BladeForums are "steel snobs meeting points" and all the non-super steels are ridiculed, smashed and trashed by the members there all day long.
Here is just the opposite
-
@Aloha007 said:
I'm not sure I agree, "a lot of MTO folks trash talk 420HC". Could be I'm not reading those posts ?Perhaps. OR. Everytime a Wave vs. Charge thread comes up, the biggest thing is how much better the Charge is, because of s30v plain blade. My argument is that 420hc is still a fine steel for blades and s30v is not worth the extra $80! My mind may be poisoned beyond reproach on the subject, because of that. My apologies. I'll stand corrected for the time being.

-
I dislike 420hc so much that I upgraded the blade in my skeletool just to get 154cm and made sure to buy a Charge AL rather than the Wave for the same reason. :D

-
I dislike 420hc so much that I upgraded the blade in my skeletool just to get 154cm and made sure to buy a Charge AL rather than the Wave for the same reason.
Aloha, Pablo, and Peacant.
I present evidence that my statement earlier remains valid.
I would hardly call my statement 'trash talk'. I have a personal opinion, one based on my own experience and influencing my own purchasing decisions which has been aired for the very first time here on the forum.
-
I dislike 420hc so much that I upgraded the blade in my skeletool just to get 154cm and made sure to buy a Charge AL rather than the Wave for the same reason.
Aloha, Pablo, and Peacant.
I present evidence that my statement earlier remains valid.
I would hardly call my statement 'trash talk'. I have a personal opinion, one based on my own experience and influencing my own purchasing decisions which has been aired for the very first time here on the forum.
I was being more cheeky than serious. So no offense was intended. 8) You are stating your preference for the first time, but it is a preference that has been a common theme among some charge/wave/skeletool users on the forum from my personal observations.
I never stated EVERY or MOST users have said 420HC was a poor steel, but that a 'lot' of users say it is a poor blade steel. For the record, a 'lot' is purely subjective.No offense was ever intended to anyone. I was just mentioning I was glad to see someone say something really great about 420HC. And, I stepping out of this thread and not looking back, before I offend anyone else unintentionally. Bye.

-
I dislike 420hc so much that I upgraded the blade in my skeletool just to get 154cm and made sure to buy a Charge AL rather than the Wave for the same reason.
Aloha, Pablo, and Peacant.
I present evidence that my statement earlier remains valid.
I would hardly call my statement 'trash talk'. I have a personal opinion, one based on my own experience and influencing my own purchasing decisions which has been aired for the very first time here on the forum.
I was being more cheeky than serious. So no offense was intended. 8) You are stating your preference for the first time, but it is a preference that has been a common theme among some charge/wave/skeletool users on the forum from my personal observations.
I never stated EVERY or MOST users have said 420HC was a poor steel, but that a 'lot' of users say it is a poor blade steel. For the record, a 'lot' is purely subjective.No offense was ever intended to anyone. I was just mentioning I was glad to see someone say something really great about 420HC. And, I stepping out of this thread and not looking back, before I offend anyone else unintentionally. Bye.

Cool, just didn't want to be seen as trash talking.

-
I dislike 420hc so much that I upgraded the blade in my skeletool just to get 154cm and made sure to buy a Charge AL rather than the Wave for the same reason.
Aloha, Pablo, and Peacant.
I present evidence that my statement earlier remains valid.
:D
What I find interesting is how some including myself move thru steels. I may have posted about why or how some people begin with certain steel and move to super steels. I'm certainly "one of those people" however I personally haven't bashed any steels. I can see now how anyone would have this perspective especially when looking at the Wave/Charge series.
When the discussion on which MT to get comes up between the Wave and Charge MTs inevitably the talk of blade steel is brought up. Titanium is part of that talk as well but certainly the S30V or 154CM blades are a main focus.
I would tend to agree with what you wrote here but......
@gerleatherberman said:
Perhaps. OR. Everytime a Wave vs. Charge thread comes up, the biggest thing is how much better the Charge is, because of s30v plain blade. My argument is that 420hc is still a fine steel for blades and s30v is not worth the extra $80! My mind may be poisoned beyond reproach on the subject, because of that. My apologies. I'll stand corrected for the time being.
Many of us fully agree with you about the extra money for the TTi. I've almost exclusively said as much. Whats interesting is over time I've had a slight change to my thoughts. While I still believe the Wave is the best bang for the buck vs the TTi or AL for those who prefer a "better" steel maybe not. Let me give you an example. I don't always carry a dedicated blade. I use my MT blade as my go to blade. Lots of users do the same so a nicer steel makes sense and the additional cost does too. I'd probably get a Delica and Wave for the same price as a TTi tho.
I got my TTi pretty cheap and carried it early on over my Wave. It didn't last long tho and went back to my Wave. I recently began to carry my TTi and I can say I love it. Yes part in due to the blade steel and part cause I just dig the Ti scales. If I'm being honest I also have carried my Skeletool CX over a regular Skeletool because the blade steel.
Maybe over time I've grown more fond of "super steels" vs 420HC
. Probably. I do like VG10 but that being said I have made comments about wanting a nicer steel on my Delica. I'm probably making your view stronger and thats ok. What I'm trying to illustrate is while I personally am preferring these steels to 420HC its not a knock against 420HC. At least not trying to do so.What I said earlier was its interesting how even me preferring certain steels will have no qualm carrying a SAK. I hope I'm not a steel snob tho maybe slowly I am becoming one.
All views are important to this site. If you feel theres any negative talk about 420HC its your right to speak up in favor of it. I never wanted to "come at you" or have it appear that way. I just hadn't looked at any conversation I've read as negative regarding 420HC. I can certainly see how perception ( my own ) could be limited.
-
There's no such thing as too sharp.

-
When I was just out of high school, I had a job at a cider factory. One day, I was cutting the binding straps on a palate of cardboard boxes, and my little slip joint buck knife was kind of dull. I heaved and cut through the strap, but also took most of the knuckle off the ring finger of my opposing hand.
Since then, I have tried hard to keep my knives sharp.
My level of 'sharp' is pull cutting receipt paper smoothly.
Beyond that, FOR ME, is a waste of my time. Although a few times recently, I've stropped to go beyond that, but just to see if I could.
As for what KIND of steel I like. I have to admit, 100%, for ease of sharpening, and holding an edge well, I think Victorinox blades are just about in the perfect spot. Again, just my taste. But, when you can do a few strokes on either side of a blade on ceramic rods and BOOM, back to super sharp... That's hard to beat, IMO.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login