Spirit 30 day Challenge with a few Early- early Birds
-

ABSO-SMERF'N-LUTELY -
What Doug said 8) That patch matches really great MM

Flint you can start now as an early bird and keep up with what day you are or you can start on the 10th when a few are all starting together

-
-
Day 3
Dawn. Phillip the Recessed Screw burrows deep into the ground. Cozy. Proud. And oblivious.
Spoiler:

Phillip is minding his own business, but alas, he is himself the business of someone else, someone much higher on the food chain.
Victor, keen for an easy kill, approaches silently, with its proboscis ready to get to work.Spoiler:

Victor pounces, reaching deep into Phillip's abode. The affair is smooth, rapid, and deadly.
Spoiler:

His thirst far from quenched, Victor calls again and again, along the whole colony.
Spoiler:

There are no more bodies to add to the gruesome pile. The colony is decimated. Victor rests, and the screws across the plains convince themselves, foolishly, that they are safe.
Spoiler:

-
@ReamerPunch said:
Victor pounces, reaching deep into Phillip's abode. The affair is smooth, rapid, and deadly.You should write romance novels. :D
-
@ReamerPunch said:
Day 3Dawn. Phillip the Recessed Screw burrows deep into the ground. Cozy. Proud. And oblivious.
definitely fun!

My Vic just cut up some thick rubber matting with its "ridiculous" butter blade, nothing it can't do

this challenge is so easy with this tool :ahhh
-
Great pics RP and funny :D

Great pic Peacent and yes the Spirit is quite capable with that butter knife blade

-
Day 4:
Riding along during work.

Got a maintenance round today since alot of customers and businesses are having a day off and are not contactable. -
Day 4: I need a torch screwdriver. The LM (non-universal) Tool Adapter works surprisingly well on the Spirit.

-
Great pics Nick and italo

-
-
Good to have you on board Harley !

-
Day5

-
-
Day 5 of 30
One of these has the on site tower crane in the reflection and the other doesn't
couldn't decide which one to use so you get both :D
0102181229 by Poncho 65, on Flickr
0102181229a by Poncho 65, on Flickr -
Nice, love the Crane reflection !

-
Day 2
Adjusted the stopper on my wife's sink.
I love my little edc flashlight, it helped out too.


Sent from my SM-G930P using Tapatalk
-
-
Great use Flint

-
Day 04:
The first hint of a concern with the Spirit arose today. Let me explain:
I decided to make a billy can for boiling water in the field from an old tomato can. I tossed the can on the grill yesterday and burnt out the lining. Then boiled some water with a bit of vinegar in the can to get rid of the residue and clean it out. So far, so good.
I used the Spirit's file to clean up the sharp edges of the can where the lid had been cut away.

The file worked well, but left it's own coarse sratches in the metal lip. I cleaned these scratches up with a quick wipe of sandpaper. Nice.
Next, I used the Spirit's punch to bore a hole on either side of the mouth. I drove the reamer through the can from the inside, knowing that I could use the file to clean up and jagged edges formed from 'drilling' out the holes. A small piece of leather supported the can and protected the point of the reamer.

Now here is where the concern is: when I examined the reamer after punching the holes in the can (with a little twist to open them up), I noticed that a small section of the edge of the reamer had been chipped (torn?) off, a few millimeters back from the tip. This is the spot where I twisted the reamer to open the hole in the can. At first I thought the edge had just rolled and used a stone to sharpen the reamer back up, but then I inspected the edge with a jeweler's loop and noticed some clear chipping.
This disappoints me. Drilling a hole in a can is something an awl/reamer/punch should be able to do. For comparison, I dug out my Rebar and did the same test on a similar can. No edge damage at all. I prefer the Spirit's more narrow reamer design, but I have to give the nod to the Rebar that can do the same task without getting torn up. I suspect that Victorinox's steel is too soft here and that the edge just got torn up by the drilling/twisting action. (I tried to get a photo of the edge, but I couldn't master the demands of Macro photography.)
I did end up using the file again to clean the jagged metal edges created by drilling my handle holes. Finally, I used the wire cutters to cut a length of tie wire and then used the pliers to crimp the wire into a bail for the billy can.

So, task accomplished, but I'm now concerned about the strength of the reamer. Might need to find some extra tasks for this tool to attempt.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

