Spirit 30 day Challenge with a few Early- early Birds
-
@ReamerPunch said:
Victor pounces, reaching deep into Phillip's abode. The affair is smooth, rapid, and deadly.You should write romance novels. :D
-
@ReamerPunch said:
Day 3Dawn. Phillip the Recessed Screw burrows deep into the ground. Cozy. Proud. And oblivious.
definitely fun!

My Vic just cut up some thick rubber matting with its "ridiculous" butter blade, nothing it can't do

this challenge is so easy with this tool :ahhh
-
Great pics RP and funny :D

Great pic Peacent and yes the Spirit is quite capable with that butter knife blade

-
Day 4:
Riding along during work.

Got a maintenance round today since alot of customers and businesses are having a day off and are not contactable. -
Day 4: I need a torch screwdriver. The LM (non-universal) Tool Adapter works surprisingly well on the Spirit.

-
Great pics Nick and italo

-
-
Good to have you on board Harley !

-
Day5

-
-
Day 5 of 30
One of these has the on site tower crane in the reflection and the other doesn't
couldn't decide which one to use so you get both :D
0102181229 by Poncho 65, on Flickr
0102181229a by Poncho 65, on Flickr -
Nice, love the Crane reflection !

-
Day 2
Adjusted the stopper on my wife's sink.
I love my little edc flashlight, it helped out too.


Sent from my SM-G930P using Tapatalk
-
-
Great use Flint

-
Day 04:
The first hint of a concern with the Spirit arose today. Let me explain:
I decided to make a billy can for boiling water in the field from an old tomato can. I tossed the can on the grill yesterday and burnt out the lining. Then boiled some water with a bit of vinegar in the can to get rid of the residue and clean it out. So far, so good.
I used the Spirit's file to clean up the sharp edges of the can where the lid had been cut away.

The file worked well, but left it's own coarse sratches in the metal lip. I cleaned these scratches up with a quick wipe of sandpaper. Nice.
Next, I used the Spirit's punch to bore a hole on either side of the mouth. I drove the reamer through the can from the inside, knowing that I could use the file to clean up and jagged edges formed from 'drilling' out the holes. A small piece of leather supported the can and protected the point of the reamer.

Now here is where the concern is: when I examined the reamer after punching the holes in the can (with a little twist to open them up), I noticed that a small section of the edge of the reamer had been chipped (torn?) off, a few millimeters back from the tip. This is the spot where I twisted the reamer to open the hole in the can. At first I thought the edge had just rolled and used a stone to sharpen the reamer back up, but then I inspected the edge with a jeweler's loop and noticed some clear chipping.
This disappoints me. Drilling a hole in a can is something an awl/reamer/punch should be able to do. For comparison, I dug out my Rebar and did the same test on a similar can. No edge damage at all. I prefer the Spirit's more narrow reamer design, but I have to give the nod to the Rebar that can do the same task without getting torn up. I suspect that Victorinox's steel is too soft here and that the edge just got torn up by the drilling/twisting action. (I tried to get a photo of the edge, but I couldn't master the demands of Macro photography.)
I did end up using the file again to clean the jagged metal edges created by drilling my handle holes. Finally, I used the wire cutters to cut a length of tie wire and then used the pliers to crimp the wire into a bail for the billy can.

So, task accomplished, but I'm now concerned about the strength of the reamer. Might need to find some extra tasks for this tool to attempt.
-
Nix, here's the awl on my old Spirit, dunno if the pic shows it well, but I had the same thing as you describe at first. I didn't sharpen it right away, actually I never have, and this is several years of on and off use. I mostly use it on softer materials, but I do use it on steel too, deburring drilled holes, punching light sheet metal, etc. I have found it develops a 'working edge' over time and stays more or less the same, not as sharp as new, but sharp enough for my purposes. I thought I would be sharpening it regularly too, but never have, I just use it as is.


-
Good pic, twiliter. That's pretty much what mine looked like, just a bit closer to the tip.
I was tempted just to leave the edge alone, but when I first thought it had just 'rolled' I figured I could restore it easily with a stone. I now have it to the point where it will slice an index card or thick paper, but balks at newspaper. For fun, I may see if I can get this thing really sharp. But, I think you are right and that given the pressures of using it like a drill bit, it's likely to get damaged again. Perhaps 'working edge' is good enough.
Still, I think this shows that the steel either needs to be hardened better or be closer to a tool steel.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

