D_T's Project MegAlox - and naming GAW
-

I haven't weighed it. It is now also very busy attracting pocket lint, so will increase in weight :D. I'll weigh it later. It feels positively massive.
-
Awlsome work and it truly is a beauty! Writeup is good too.
Seems like it could fix about anything so while you watch others try and fail you feel this beauty in your pocket and after a minute or two you just say "stop! I will fix this!" and then get the job done.. But after a couple of times you just want the job done and pick the tool up and say Ifix (not affiliated with Apple, but as a dry joke).. This boils down to the fact that my suggestion for a name is "iFix" and that pioneer is a nice one too [emoji5]
[It's not failure if you learn something from it]
-
@Mechanickal said:
A mechanic + explorer?The Mexplorer!
Or
The Explanical! :DSince you EXPLAiNed your mod, that might be the better one?
And that Pioneer...

Where did you find those screw rivets??
Brilliant - the Explanical...
will think about it.The screws are M2 sunken-head Torx (various lengths as necessary: I used a mix of 10, 8 and 5 mm lengths) and screwed plus loctited onto the brass pivots. Available at conrad.de for instance.
-
What was it like tapping the M2 threads into 1.5mm holes? The tapping drill should be 1.6mm though it probably makes little difference.
-
@hiraethus said:
What was it like tapping the M2 threads into 1.5mm holes? The tapping drill should be 1.6mm though it probably makes little difference.Yup, should be 1.6 mm - but this makes no appreciable difference, in brass. I also only used the no. 1 and 2 taps. Both measures were taken in order to keep the contact between the threads of the screws and pivot as intimate as possible - complemented with loctite (or rather the strong variant of a local equivalent) for the final lock.
Tapping was no problem - put the pivot in the lathe chuck and use a tapping tool handle to carefully tap the thread (keeping it aligned with the lathe bed). With a lathe on slow speed you can also turn the pivot that way whilst keeping the tapping tool handle still, if you feel brave (I did, after a few pivots) and let loose at the right instant.
Drilling the holes before tapping is likewise best carried out on a lathe. Some tips:
(1) use a centre drill, at least the first time
(2) drill through past the length of the pivot to have a centre hole for the next pivot (avoids repetition of (1))
(3) retract the drill once every few mm of advance, bits of drilled out metal tend to assemble around the drill bit point and might snag it, with breakage of the bit as a result. -
TaskMaster
Quite the set-up.

-
Great SAK, call it The Do-it.
Sent fra min FRD-L09 via Tapatalk
-
Awesome mod D_T...

Got 2 name suggestions:
- The Tooler
- ToolChamp
Names befits its owner...

Sent from my iPhone using Tapatalk
-
Great work !

-
nice work. First thing that came to mind when I saw it was holy smurf
-
Awesome alox mod

I would call it the alox Master Ranger Plus
:DVery nice 8)

-
@Dutch_Tooler said:
Thanks all
...holy smurf
Is that your naming suggestion?
I'd capitalize it, for sure...That's a brilliant suggestion with the colour an all

The Holy Smurf.
-
That's a great job building a very nice SAK.
I gotta second the suggestion of 'Explanical'.

-
Or it's a Ranger with pliers?
It's a Power Ranger!

And it's the blue one ;) ;) ;)
-
@Dutch_Tooler said:
Hi all,Here is the result of a project that has kept my leisure time busy the last weeks.
Nicely done DT!

-
Thanks guys

I have just been notified of a law suit initiated against me by the NAPAKS (National Association for the Prevention of the Abuse of Kitchen Scales).
My impression was correct, at least qualitatively. The MegAlox weighs in at a whopping 182 grams (6.4 oz). This is just 3 grams short of what the SAKWiki reports for the SwissChamp.
-
Bravo! Bravo sir! I'm trying to do something similar. 2x recruits with a wood saw in the middle. I have it done with celidor scales and peened. But I have a red scaled cadet coming my way and I'm thinking to thread it three way you did it instead. 2.25 mm is kinda thin to drill into though and I don't have anything more than a handheld drill. Any advice it's very welcome!

Sent from my SM-G935F using Tapatalk
-
That is a beauty, congrats on the good work.
I will go with (thanks to the recent Super Bowl LII) The Linebacker.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login