D_T's Project MegAlox - and naming GAW
-
Awesome alox mod

I would call it the alox Master Ranger Plus
:DVery nice 8)

-
@Dutch_Tooler said:
Thanks all
...holy smurf
Is that your naming suggestion?
I'd capitalize it, for sure...That's a brilliant suggestion with the colour an all

The Holy Smurf.
-
That's a great job building a very nice SAK.
I gotta second the suggestion of 'Explanical'.

-
Or it's a Ranger with pliers?
It's a Power Ranger!

And it's the blue one ;) ;) ;)
-
@Dutch_Tooler said:
Hi all,Here is the result of a project that has kept my leisure time busy the last weeks.
Nicely done DT!

-
Thanks guys

I have just been notified of a law suit initiated against me by the NAPAKS (National Association for the Prevention of the Abuse of Kitchen Scales).
My impression was correct, at least qualitatively. The MegAlox weighs in at a whopping 182 grams (6.4 oz). This is just 3 grams short of what the SAKWiki reports for the SwissChamp.
-
Bravo! Bravo sir! I'm trying to do something similar. 2x recruits with a wood saw in the middle. I have it done with celidor scales and peened. But I have a red scaled cadet coming my way and I'm thinking to thread it three way you did it instead. 2.25 mm is kinda thin to drill into though and I don't have anything more than a handheld drill. Any advice it's very welcome!

Sent from my SM-G935F using Tapatalk
-
That is a beauty, congrats on the good work.
I will go with (thanks to the recent Super Bowl LII) The Linebacker. -
I like the sound of mega man AKA “the blue bomber” since it feels like a bomb in your pocket and it has enough tools to take care of anything that gets in its way.
-
Awesome job on the mod, will this work with ether mag and Philips or only the new one?
-
Thanks, all

@stoneshank said:
I'm thinking to thread it three way you did it instead. 2.25 mm is kinda thin to drill into though and I don't have anything more than a handheld drill. Any advice it's very welcome!I'd advise against trying that with brass. Assuming you'd be able to centre the drill properly and have it (or the pivot) turn true to axis (no mean feat by hand, I think), you'd have a remaining wall thickness of 0.375 mm, into which you'd have to tap thread (assuming you're talking M2 and drilling to 1.5 mm - smaller screws tend to have too small heads and may lack strength). Even assuming you'd manage to clamp the pivots without crushing them for drilling and tapping (ideally you'd use lathe or drill chucks), I think you'd have the pivots fold up on you while assembling the knife. For that kind of wall thickness, stainless steel would be my intuitive choice, but that requires excellent tooling and skills (beyond me in any case). I believe most people who adapt 91 mm SAKs to threaded pivots use at least 3 mm for the live pivots (2.5 mm will work for the fake centre pivots on 93 mm alox models), or even the somewhat larger 1/8" pivots obtainable in the US (these are stainless steel, at least as an option, I believe). Tools would have to be drilled to suit though, and again, by hand, that is not easy to do with the required precision (you'd need a tungsten carbide insert equipped drill bit and slow RPMs; axis needs to be exactly perpendicular to the tool tang).
But in my experience, as limited as it is, hand peening solid brass pivots is very doable for 91 mm models, and would save a lot of hassle. There is the aesthetic appeal of screw heads which you'd miss then, of course.
@Simyo said:
Awesome job on the mod, will this work with ether mag and Philips or only the new one?Can't compare old and new at the moment. Assuming both sets are equally thick, this should be possible as lengthwise the old and new ones require the same space (or thereabouts, by memory). It could be however that the old ones are a tad thicker (at least the old grey magnifier, from memory, gives a very slightly thicker impression, which would have to apply to the Phillips too - can anyone conform or deny this?) in which case the back spring might need to be thicker too - then the 93 mm blades back spring would be too thin. One could solve this with washers, but that would be less elegant.
-
Very nice mod.
-
Thanks all

...holy smurf
Is that your naming suggestion?
I'd capitalize it, for sure...That's a brilliant suggestion with the colour an all

The Holy Smurf.
me thinks Mags gets the credit for that one
Credits all yours dude - I was just adding my appreciation

-
Thanks all

[quote author=styx link=topic=75772.msg1630640#msg1630640 date=1517839202]
...holy smurfIs that your naming suggestion?
I'd capitalize it, for sure...That's a brilliant suggestion with the colour an all

The Holy Smurf.
me thinks Mags gets the credit for that one
Credits all yours dude - I was just adding my appreciation

[/quote]tell you what, we'll mas wrestle for it. loser gets the prize (if the name is chosen)
-
Great looking knife! Here are some naming suggestions: ** Alox ToolBox, ToolOx, Workalox, WorkOx**
-
Good mod and a LOT of useful info, thank you + good job.
My suggestions are: The DutchTool and DutchAlox :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
