Bending a LM tool
-
Hi there,
I'm making a custom MT and for this project I need to bend a LM can opener tool.
I just want to bend it sideways, by about 10°, and the bend distributed over the entire length of the tool. A very easy bend.
Well, it should be very easy at least. If we we talking plain steel/copper/most metalsThe other requirement is that the tool doesn't lose its hardness. This is crucial as I intend to sharpen one of the edges of this can opener, and ofcourse I'd like it to stay sharp as long as possible.
So in conclusion I need to
1 ) Determine exactly what type of steel a LM can opener is made from
2 ) Then I can look up the appropriate way to bend it. ( Heat? To what temperature? Bend when hot or once it has cooled down? Or bend when cold? Is work hardening g an issue? ... )
3 ) Look up how to re-harden the tool ( IF it had to be softened first to do the bend in the first place)So far I'm still stuck on number 1.
There are many types of stainless steels, and each have different ways to bend and/or heat treat them...Anybody with knowledge on any if these three points?
Anybody who has bent These/similar tools before?Thanks
-
Zachary Fowler discusses how he turned the can opener on his Victorinox Spirit into a spoon gouge. I've set the time stamp to where he discusses this particular mod. TLDR: Heat until cherry red, hit with hammer. You can't take Spirits apart, but you CAN take Leatherman tools apart. I'd recommend doing that if you intend to modify the can opener by heating it to glowing red.
What >I< would personally do is remove the can opener from the rest of the tool, heat, shape, then heat again, using a magnet to test to make sure that you're heating it until the magnetic attraction goes away, then quench in water/oil. This will make it HARD. Then put it in an oven at 450 for a few hours to temper. I don't know what steel it's made of, but that's pretty standard for any tool you want to have a cutting edge. Whether or not it will WORK...

-
Want to bend a tool?
Pablo O'Brien is the man to talk to here! 8) -
Leatherman uses 420HC on their blades , maybe something else for the can openers 440

-
If you hit with a hammer, it'll just snap off. You'll have to heat it up with a torch first. Good luck!
Or like Mechy says, get Pablo to do it!
-
@Fuzzbucket said:
If you hit with a hammer, it'll just snap off. You'll have to heat it up with a torch first. Good luck!Or like Mechy says, get Pablo to do it!
Doesn't heating steel make it "un-steel"? AFAIK heating up a hardened and processed steel makes interferes with the molecular structure and softens it.

-
If you hit with a hammer, it'll just snap off. You'll have to heat it up with a torch first. Good luck!
Or like Mechy says, get Pablo to do it!
Doesn't heating steel make it "un-steel"? AFAIK heating up a hardened and processed steel makes interferes with the molecular structure and softens it.

Yeah I imagine it will, but there is no other way that I can think of. If indeed leatherman do heat treat components like can-openers etc...?

-
Whatever metal/tempering Leatherman uses, the metal tends to snap, not bend. I've seen a lot more broken implements than severely bent ones on Leatherman tools. So, yes, heating would be crucial.
-
@Fuzzbucket said:
It's a horribly distinctive sound when they ping off too... (gulp)...I broke the file on a Wingman TWICE, and the phillips on a Micra. I know the 'ping' all too well. :D
-
Everything is 420, Blades are 420HC
-
@Rebelgium said:
Hi there,I'm making a custom MT and for this project I need to bend a LM can opener tool.
I just want to bend it sideways, by about 10°, and the bend distributed over the entire length of the tool. A very easy bend.Which size/type LM can opener, Wingman, Wave, Surge, OHT, other?
Bend to which side, left or right? -
Hi there,
I'm making a custom MT and for this project I need to bend a LM can opener tool.
I just want to bend it sideways, by about 10°, and the bend distributed over the entire length of the tool. A very easy bend.Which size/type LM can opener, Wingman, Wave, Surge, OHT, other?
Bend to which side, left or right?Wave size. I'll bend it to the left (looking from the top of the tool)
-
@Lynn LeFey said:
@Fuzzbucket said:
It's a horribly distinctive sound when they ping off too... (gulp)...I broke the file on a Wingman TWICE, and the phillips on a Micra. I know the 'ping' all too well. :D
My speculation: A file will be hardened, but not tempered. Leaving it very hard (as a file should be) but brittle.
I think a canopener will be tempered. That is, if it is hardened at all. So a canopener should be less brittle -
Hi there,
I'm making a custom MT and for this project I need to bend a LM can opener tool.
I just want to bend it sideways, by about 10°, and the bend distributed over the entire length of the tool. A very easy bend.Which size/type LM can opener, Wingman, Wave, Surge, OHT, other?
Bend to which side, left or right?Wave size. I'll bend it to the left (looking from the top of the tool)
Okay, no promises but if I can find a couple spares and some free time at work next week I'll do some testing.
-
Hi there,
I'm making a custom MT and for this project I need to bend a LM can opener tool.
I just want to bend it sideways, by about 10°, and the bend distributed over the entire length of the tool. A very easy bend.Which size/type LM can opener, Wingman, Wave, Surge, OHT, other?
Bend to which side, left or right?Wave size. I'll bend it to the left (looking from the top of the tool)
Okay, no promises but if I can find a couple spares and some free time at work next week I'll do some testing.
That would be great! Very interested in the results.
I'd do some testing too but I have no spares, it's a one shot deal.I've done some measurements and I need to make a correction: I'd bend the last 18mm by 20° to the left side. By the last 18mm I mean the tip of the tool, the hinge needs to stay straight.
-
[quote author=Rebelgium link=topic=75797.msg1631675#msg1631675 date=1517931675]
Hi there,I'm making a custom MT and for this project I need to bend a LM can opener tool.
I just want to bend it sideways, by about 10°, and the bend distributed over the entire length of the tool. A very easy bend.Which size/type LM can opener, Wingman, Wave, Surge, OHT, other?
Bend to which side, left or right?Wave size. I'll bend it to the left (looking from the top of the tool)
Okay, no promises but if I can find a couple spares and some free time at work next week I'll do some testing.
That would be great! Very interested in the results.
I'd do some testing too but I have no spares, it's a one shot deal.
[/quote]
:D
-
Give it a go with the one you have - if it snaps I'll send you a replacement.
-
Maybe a sketch is in order so we can get some idea of how far you're trying to bend it. And what you're trying to fit it into.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login