Bending a LM tool
-
-
-
-
-
-

Really cool stuff there! :o -
Nice work [emoji3]
[It's not failure if you learn something from it]
-
Yessss - nice one Zoidberg!!!

-
Nice work, and nice pics. I really like the way the tin-can was decimated. -
Nicely done Zoidberg

I Was really interested in the results
-
@Mechanickal I'm from Brugge
@bePrepared thanks a lot! PM sent
@Zoidberg wicked! Thanks for the experiments, very interesting!
So let me recap to see if I got this correctly:Cold bending with hammer snapped the canopener at 5mm deflection.
So you turned to hot bending:- heat to cherry red
- let cool down slowly by air (=annealing)
- once it cooled down: bend with hammer
- heat up again to cherry red
- dunk in water (=hardening)
- no tempering
- sharpen
- annihilate can
Is this all correct?
Remarks?
Any idea of temperatures?
Do you think the hardening without tempering has left it too brittle for hard use? -
Looks like Zoidberg did some serious testing on that can in the photos

-
Nicely done zoid !

-
@Rebelgium said:
@Zoidberg wicked! Thanks for the experiments, very interesting!
So let me recap to see if I got this correctly:Cold bending with hammer snapped the canopener at 5mm deflection.
So you turned to hot bending:- heat to cherry red
- let cool down slowly by air (=annealing)
- once it cooled down: bend with hammer
- heat up again to cherry red
- dunk in water (=hardening)
- no tempering
- sharpen
- annihilate can
Is this all correct?
Yes, this is all correct.
@Rebelgium said:
Remarks?Don't bother with cold bending.
@Rebelgium said:
Any idea of temperatures?I think the map fuel flame air temp is around 2000°C.
@Rebelgium said:
Do you think the hardening without tempering has left it too brittle for hard use?Good question. Define hard use. When I can find the time I'll test it to failure.
-
Great work on that, Zoidberg.
I wholeheartedly approve of test-to-failure.


If I were to guess, the lack of annealing will leave it more brittle than it was originally, but I'm not sure harder/more brittle is a bad thing with a can opener. They're not really subject to that much flex in use.
-
Specifications on various alloys usually have some information and specific recipes for annealing and hardening treatments of that particular steel quality. For 420 stainless steel an example can be found at http://www.aksteel.com/pdf/markets_products/stainless/martensitic/420_data_sheet.pdf
-
Would hardening in oil leave it less brittle ?
-
@SteveC said:
Would hardening in oil leave it less brittle ?According to the spec sheet for 420 stainless steel it should be quenched in warm oil when hardening. As steels can be optimized for hardening with various media I think following the steel manufacturers directions might be a good idea. (Including tempering after quenching to make the right balance between hard/brittle and tough/ flexible).
The overall idea is to quench quick enough to get the part hardened to the required depth but no faster than necessary. Faster cooling increases residual stresses and thus the risk of cracks or deformation. Faster cooling also tends to make harder and more brittle parts.
Water has a lower boiling point than oil and hence cools the part faster. So yes, it will likely be less brittle by oil quenching instead.
(Heat treatment and metallurgy are huge subjects on their own. I'm certainly no speSmurfpillst in either by any means, but the above is my big picture understanding summarized in a few lines).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login









