Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Home solution for loose pliers pivot! Experiment!

Scheduled Pinned Locked Moved Leatherman Tools
96 Posts 1 Posters 19.7k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Home solution for loose pliers pivot! Experiment!
Home solution for loose pliers pivot! Experiment!
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Sam Lim Offline
    Sam Lim
    Posts: 2,306
    Sam Lim Offline
    Sam Lim
    wrote on last edited by
    #66 Quote Reply

      @srvctec said:
      Couldn't get this tip to work on my Tti Charge. Clamped it unbelievably tight with my small Vice Grips using card stock discs I cut out with a hole punch for protection and it wouldn't budge. Tried it in my vise with the same results. I wound up doing what I've done for 40 years on pliers with this pivot type- put the ball end of a ball peen hammer right in the center of the pivot and smacked it with another hammer. It's perfect now like it was out of the box over 2 years ago.

      Probably wouldn't work with all but most I would say.

      Btw doing what you do are rather unsafe.. Hammer on hammer is not a good idea.. Shards may fly... U should use a punch or something "softer"..

      1 Reply Last reply
      • Sam Lim Offline
        Sam Lim
        Posts: 2,306
        Sam Lim Offline
        Sam Lim
        wrote on last edited by
        #67 Quote Reply

          Where to grip on the pivot is always a trial and error. Doesn't mean gripping dead centre will turn it. A little hard to explain.. But when u have all the tools on hand, before clamping down, have a mental picture of where you clamp may have the most effect in turning it. So far, worked on most. I did also encounter one or two that refuse to budge. A few were loose beyond this method can help. So the punch and hammer would still have to come in for those nasty ones.

          1 Reply Last reply
          • srvctec Offline
            srvctec
            Posts: 34
            srvctec Offline
            srvctec
            wrote on last edited by
            #68 Quote Reply

              @Sam Lim said:

              @srvctec said:

              Couldn't get this tip to work on my Tti Charge. Clamped it unbelievably tight with my small Vice Grips using card stock discs I cut out with a hole punch for protection and it wouldn't budge. Tried it in my vise with the same results. I wound up doing what I've done for 40 years on pliers with this pivot type- put the ball end of a ball peen hammer right in the center of the pivot and smacked it with another hammer. It's perfect now like it was out of the box over 2 years ago.

              Probably wouldn't work with all but most I would say.

              Btw doing what you do are rather unsafe.. Hammer on hammer is not a good idea.. Shards may fly... U should use a punch or something "softer"..

              Thanks but I'm fully aware of that and didn't even come close to using enough force to cause a flying shard of either hammer. I've never chipped a hammer in my 51 years of using them frequently.

              1 Reply Last reply
              • aikon2014 Offline
                aikon2014
                Posts: 164
                aikon2014 Offline
                aikon2014
                wrote on last edited by
                #69 Quote Reply

                  I have 4 Rebars, one bladeless, two regular and one BO. All of them were "loose" in the pliers, no play, but loose, I personally prefer resistance in the pliers. Tried the method, took a couple of washers that were the exakt size of the pivot, clamped down with a lockable plier tool and turned. I found 1. it does matter where you clamp down on the pivot, it differed with the different Rebars. 2. It does matter which turning movement you use, i first tried to just move the clamped plier and it didn't work until I realized that I had to use a cirkular motion to really move the pivot.

                  Great tips, I'm happy with my "renewed" Rebars :)

                  1 Reply Last reply
                  • Wspeed Offline
                    Wspeed
                    Posts: 76,225
                    Wspeed Offline
                    Wspeed
                    wrote on last edited by
                    #70 Quote Reply

                      @aikon2014 said:
                      I have 4 Rebars, one bladeless, two regular and one BO. All of them were "loose" in the pliers, no play, but loose, I personally prefer resistance in the pliers. Tried the method, took a couple of washers that were the exakt size of the pivot, clamped down with a lockable plier tool and turned. I found 1. it does matter where you clamp down on the pivot, it differed with the different Rebars. 2. It does matter which turning movement you use, i first tried to just move the clamped plier and it didn't work until I realized that I had to use a cirkular motion to really move the pivot.

                      Great tips, I'm happy with my "renewed" Rebars :)

                      Hi glad you got it to work :tu:
                      My LM supertool was loose from day one :rofl:
                      But this little trick made them how they should be
                      Well done aikon2014 :tu:

                      1 Reply Last reply
                      • aikon2014 Offline
                        aikon2014
                        Posts: 164
                        aikon2014 Offline
                        aikon2014
                        wrote on last edited by
                        #71 Quote Reply

                          @Wspeed said:

                          @aikon2014 said:

                          I have 4 Rebars, one bladeless, two regular and one BO. All of them were "loose" in the pliers, no play, but loose, I personally prefer resistance in the pliers. Tried the method, took a couple of washers that were the exakt size of the pivot, clamped down with a lockable plier tool and turned. I found 1. it does matter where you clamp down on the pivot, it differed with the different Rebars. 2. It does matter which turning movement you use, i first tried to just move the clamped plier and it didn't work until I realized that I had to use a cirkular motion to really move the pivot.

                          Great tips, I'm happy with my "renewed" Rebars :)

                          Hi glad you got it to work :tu:
                          My LM supertool was loose from day one :rofl:
                          But this little trick made them how they should be
                          Well done aikon2014 :tu:

                          Thanks :)

                          1 Reply Last reply
                          • JustinCase Offline
                            JustinCase
                            Posts: 825
                            JustinCase Offline
                            JustinCase
                            wrote on last edited by
                            #72 Quote Reply

                              How about a solution for frozen pliers? :popcorn:.....Asking because I used my good old 2006 Wave during salt water fishing and after a couple of days the pliers got frozen shut and resisted all attempt to work them free no matter what kind of lubricant or rust corrosion I used. I tried all the YouTube and Google tricks with negative results so I stop trying and sent them for warranty repair but instead they sent me a new Wave, which is cool! :tu:

                              1 Reply Last reply
                              • Wspeed Offline
                                Wspeed
                                Posts: 76,225
                                Wspeed Offline
                                Wspeed
                                wrote on last edited by
                                #73 Quote Reply

                                  @JustinCase said:
                                  How about a solution for frozen pliers? :popcorn:.....Asking because I used my good old 2006 Wave during salt water fishing and after a couple of days the pliers got frozen shut and resisted all attempt to work them free no matter what kind of lubricant or rust corrosion I used. I tried all the YouTube and Google tricks with negative results so I stop trying and sent them for warranty repair but instead they sent me a new Wave, which is cool! :tu:

                                  That is a good question no idea :think:
                                  Excellent news that they send you a brand new Wave :tu: :like:

                                  1 Reply Last reply
                                  • JustinCase Offline
                                    JustinCase
                                    Posts: 825
                                    JustinCase Offline
                                    JustinCase
                                    wrote on last edited by
                                    #74 Quote Reply

                                      @Wspeed said:

                                      @JustinCase said:

                                      How about a solution for frozen pliers? :popcorn:.....Asking because I used my good old 2006 Wave during salt water fishing and after a couple of days the pliers got frozen shut and resisted all attempt to work them free no matter what kind of lubricant or rust corrosion I used. I tried all the YouTube and Google tricks with negative results so I stop trying and sent them for warranty repair but instead they sent me a new Wave, which is cool! :tu:

                                      That is a good question no idea :think:
                                      Excellent news that they send you a brand new Wave :tu: :like:

                                      Well, a new (old design) Wave, not the new 2018 with new pliers ;)

                                      1 Reply Last reply
                                      • Wspeed Offline
                                        Wspeed
                                        Posts: 76,225
                                        Wspeed Offline
                                        Wspeed
                                        wrote on last edited by
                                        #75 Quote Reply

                                          @JustinCase said:

                                          @Wspeed said:

                                          @JustinCase said:

                                          How about a solution for frozen pliers? :popcorn:.....Asking because I used my good old 2006 Wave during salt water fishing and after a couple of days the pliers got frozen shut and resisted all attempt to work them free no matter what kind of lubricant or rust corrosion I used. I tried all the YouTube and Google tricks with negative results so I stop trying and sent them for warranty repair but instead they sent me a new Wave, which is cool! :tu:

                                          That is a good question no idea :think:
                                          Excellent news that they send you a brand new Wave :tu: :like:

                                          Well, a new (old design) Wave, not the new 2018 with new pliers ;)

                                          Still good of LM to send you a new/old wave :tu:
                                          But yes a 2018 wave would of been even better :salute:

                                          1 Reply Last reply
                                          • aikon2014 Offline
                                            aikon2014
                                            Posts: 164
                                            aikon2014 Offline
                                            aikon2014
                                            wrote on last edited by
                                            #76 Quote Reply

                                              Btw is there any way of tightening small tools like micra, style ps, squirts and so on?

                                              1 Reply Last reply
                                              • Sam Lim Offline
                                                Sam Lim
                                                Posts: 2,306
                                                Sam Lim Offline
                                                Sam Lim
                                                wrote on last edited by
                                                #77 Quote Reply

                                                  @aikon2014 said:
                                                  Btw is there any way of tightening small tools like micra, style ps, squirts and so on?

                                                  Smallish tools peening with a punch and hammer would be best. Do it lightly though. Very lightly. Test and do again if needed.

                                                  1 Reply Last reply
                                                  • Sam Lim Offline
                                                    Sam Lim
                                                    Posts: 2,306
                                                    Sam Lim Offline
                                                    Sam Lim
                                                    wrote on last edited by Sam Lim
                                                    #78 Quote Reply

                                                      I am now trying to use a different approach to this method.

                                                      1. Using a smallish vise grip to clamp down on the pivot. Make sure u are only gripping only the pivot with the "dead" side facing you.

                                                      2. Turn the right side handle or plier head instead of turning the vise grip. There's way lesser chance of slippage and scarring. As before, make a marking before you start.

                                                      See pic. You get the idea. Turning clockwise, start with the pliers handle open and turn the right side handle. Turning anti-clockwise is a bit more tricky. U need some kind of prying lever on the plier tip side to open up to turn it anticlockwise.

                                                      IMG_20180222_191028-744x992.jpg

                                                      IMG_20180222_191056-744x992.jpg

                                                      1 Reply Last reply
                                                      • aikon2014 Offline
                                                        aikon2014
                                                        Posts: 164
                                                        aikon2014 Offline
                                                        aikon2014
                                                        wrote on last edited by
                                                        #79 Quote Reply

                                                          @Sam Lim said:

                                                          @aikon2014 said:

                                                          Btw is there any way of tightening small tools like micra, style ps, squirts and so on?

                                                          Smallish tools peening with a punch and hammer would be best. Do it lightly though. Very lightly. Test and do again if needed.

                                                          It worked! Tested it on both my Micra and Style CS, both scissors had a small play in it. Took a phillips head screqdriver (rather large one so the smal flat portion on the tip fit the round pivot) and whacked it with a hammer, small whacks first until I found the right force, and tadaa it worked like a charm! I suppose that there are other tools that are moore suited for this, but it worked, no play at all!
                                                          Thanks!

                                                          1 Reply Last reply
                                                          • ThePeacent Offline
                                                            ThePeacent
                                                            Posts: 14,599
                                                            ThePeacent Offline
                                                            ThePeacent
                                                            wrote on last edited by
                                                            #80 Quote Reply

                                                              why isn't this thread a sticky yet?! :ahhh ???

                                                              1 Reply Last reply
                                                              • aikon2014 Offline
                                                                aikon2014
                                                                Posts: 164
                                                                aikon2014 Offline
                                                                aikon2014
                                                                wrote on last edited by
                                                                #81 Quote Reply

                                                                  For the record I did put the tool itself outside of the edge of the table and put only the plierhead/scissorhead on the table to prevent ut all from bending. Just a small warning if anyone tries this :D

                                                                  1 Reply Last reply
                                                                  • aikon2014 Offline
                                                                    aikon2014
                                                                    Posts: 164
                                                                    aikon2014 Offline
                                                                    aikon2014
                                                                    wrote on last edited by
                                                                    #82 Quote Reply

                                                                      Btw, is there a way to do this to a OHT?
                                                                      The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                                                                      All the others might have been looser in the action than I like, but no play.

                                                                      Anyone tried something to fix the OHT pliers? :)

                                                                      1 Reply Last reply
                                                                      • Sam Lim Offline
                                                                        Sam Lim
                                                                        Posts: 2,306
                                                                        Sam Lim Offline
                                                                        Sam Lim
                                                                        wrote on last edited by
                                                                        #83 Quote Reply

                                                                          @aikon2014 said:
                                                                          Btw, is there a way to do this to a OHT?
                                                                          The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                                                                          All the others might have been looser in the action than I like, but no play.

                                                                          Anyone tried something to fix the OHT pliers? :)

                                                                          I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.

                                                                          1 Reply Last reply
                                                                          • aikon2014 Offline
                                                                            aikon2014
                                                                            Posts: 164
                                                                            aikon2014 Offline
                                                                            aikon2014
                                                                            wrote on last edited by
                                                                            #84 Quote Reply

                                                                              @Sam Lim said:

                                                                              @aikon2014 said:

                                                                              Btw, is there a way to do this to a OHT?
                                                                              The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                                                                              All the others might have been looser in the action than I like, but no play.

                                                                              Anyone tried something to fix the OHT pliers? :)

                                                                              I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.

                                                                              It's such a shame :( I would love to have a single hand tool for fishing situations, but no dice with the OHT :(

                                                                              1 Reply Last reply
                                                                              • Sam Lim Offline
                                                                                Sam Lim
                                                                                Posts: 2,306
                                                                                Sam Lim Offline
                                                                                Sam Lim
                                                                                wrote on last edited by
                                                                                #85 Quote Reply

                                                                                  @aikon2014 said:

                                                                                  @Sam Lim said:

                                                                                  @aikon2014 said:

                                                                                  Btw, is there a way to do this to a OHT?
                                                                                  The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                                                                                  All the others might have been looser in the action than I like, but no play.

                                                                                  Anyone tried something to fix the OHT pliers? :)

                                                                                  I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.

                                                                                  It's such a shame :( I would love to have a single hand tool for fishing situations, but no dice with the OHT :(

                                                                                  Well most still grip and cut without any noticeable problems. So I think it's still a good tool.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  • 5
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. Home solution for loose pliers pivot! Experiment!
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0