First AA flashlight suggestions?
-
@Blackbeard said:
P12 is great
get oneBut I don’t feel ready for the power of a 18650 flashlight! :ahhh
-
@Pablo O'Brien said:
P12 is great
get oneBut I don’t feel ready for the power of a 18650 flashlight! :ahhh
You are ready ;)
-
they had P12 deal back around thanksgiving, bit more money now, but you can get Covoy S2+ for under $10 and dip your foot in the water.
-
what do you mean by not ready?
-
Erm... I don’t need one yet?

Still in the “ooh cool, I have a new torch!” period with my E03H :D -
Best advice is RUN :ahhh, while you still have your whole life ahead of you
flashlight addiction is smurfing hard to escape -
Don’t worry, if past experience is anything to go by, I’ll get another light in 2020.

-
Oh, you’re soo ready for 18650 Pabs...

Forgot where I read it, but for survival situations, ideally should have at least an 18650 light and an AA/14500 light... 18650’s gives you more light... and should you run low or run out of juice, there’s always the AA/14500 as backup. Especially AA’s being the more common sized ones (at least in my part of the woods)...
AAA’s are more pocket friendly for urban EDC...

Sent from my iPhone using Tapatalk
-
We’ll see.
:D -
The Armytek Wizard Pro V3 USB is also good if you want another angled light [emoji23]
Sent from my iPhone using Tapatalk
-
Looked it up... what an awesome monstrosity! :D
-
@jaya_man said:
Oh, you’re soo ready for 18650 Pabs...
Forgot where I read it, but for survival situations, ideally should have at least an 18650 light and an AA/14500 light... 18650’s gives you more light... and should you run low or run out of juice, there’s always the AA/14500 as backup. Especially AA’s being the more common sized ones (at least in my part of the woods)...
AAA’s are more pocket friendly for urban EDC...

Sent from my iPhone using Tapatalk
Cool pics

-
Oh, you’re soo ready for 18650 Pabs...

Forgot where I read it, but for survival situations, ideally should have at least an 18650 light and an AA/14500 light... 18650’s gives you more light... and should you run low or run out of juice, there’s always the AA/14500 as backup. Especially AA’s being the more common sized ones (at least in my part of the woods)...
AAA’s are more pocket friendly for urban EDC...

Sent from my iPhone using Tapatalk
Cool pics

Thanks CeHo

-
I did some rough maths on my calculator.
The E03H has 21 possible moonlight modes, which can be programmed with "engineering mode".
Assuming that the highest (21st) moonlight setting is 1.5 lumens, and that each setting is 75% brighter than the previous one, then the lowest should be about 0.004 lumens. :ahhh
Given the uncertainty involved, give or take a few thousandths of a lumen. ::)
All I can tell you with certainty is on the lowest setting, I can just about tell that the LED is on by looking at it, that it is definitely on, and that it provides no noticeable illumination at awl, even on super close-up objects, and that the 0.02 lumen mode on my Ti3 (value measured by selfbuilt) is a blazing amount of light by comparison. -
@Pablo O'Brien said:
I did some rough maths on my calculator.
The E03H has 21 possible moonlight modes, which can be programmed with "engineering mode".
Assuming that the highest (21st) moonlight setting is 1.5 lumens, and that each setting is 75% brighter than the previous one, then the lowest should be about 0.004 lumens. :ahhh
Given the uncertainty involved, give or take a few thousandths of a lumen. ::)
All I can tell you with certainty is on the lowest setting, I can just about tell that the LED is on by looking at it, that it is definitely on, and that it provides no noticeable illumination at awl, even on super close-up objects, and that the 0.02 lumen mode on my Ti3 (value measured by selfbuilt) is a blazing amount of light by comparison.Have you tried any of those Low Lows at night with dark adjusted eyes yet though?
It can be surprising how useful they can be once you are used to the dark!
-
@Pablo O'Brien said:
I did some rough maths on my calculator.
The E03H has 21 possible moonlight modes, which can be programmed with "engineering mode".
Assuming that the highest (21st) moonlight setting is 1.5 lumens, and that each setting is 75% brighter than the previous one, then the lowest should be about 0.004 lumens. :ahhh
Given the uncertainty involved, give or take a few thousandths of a lumen. ::)
All I can tell you with certainty is on the lowest setting, I can just about tell that the LED is on by looking at it, that it is definitely on, and that it provides no noticeable illumination at awl, even on super close-up objects, and that the 0.02 lumen mode on my Ti3 (value measured by selfbuilt) is a blazing amount of light by comparison.Have you tried any of those Low Lows at night with dark adjusted eyes yet though?
It can be surprising how useful they can be once you are used to the dark!
I’m a low low mode junky, but some of these go too low for me. :D
Points of reference:
Step 15, give or take a step, is about the same brightness as the firefly on a Ti3, which is 0.04 lumen according to Thrunite, and 0.02 lumen according to Selfbuilt.
Step 18, maybe 17, is about the same as the TH20, which is 0.3 lumens according to Thrunite.
Now, on step one and not wearing glasses (I’m nearsighted to a significant degree) I can see the picture on the cover of a book, but as far as colours go, I can’t really tell them apart, besides “that’s black” “that’s white” “light colour” “dark colour” “in between”.

I can light up a paragraph of white on black text, but it’s not really comfortable.
Black on white text? Even less comfortable.
The book is about a hands length away from my eyes, it’s important to note.I have to go awl the way to step 14 to read this book comfortably.
Because of the slight awkwardness involved in changing the moonlight setting, I think that I’ll leave it somewhere in the mid teen steps most of the time, even if I can get by with less light for some tasks. The lowest steps that I’ll probably ever realistically use is likely the high single digits.
More to come in the future, it gets dark every night after all.

-
This thread has an absurd amount of views for 1 flashlight

-
What can I say? It’s an interesting flashlight. :P
-
Just started a moonlight runtime test on my E03.

Standard capacity eneloop, voltage 1.384 volts.
Manker claims 175h at 0.1 lumens with a high capacity eneloop. I think that I have mine set to higher than 0.1 lumens.
Will stay on for about 10 hours a day. -
12h later.... 1.350 volts.
And I think that I see spots on the threads bare of anodising already. ::)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login