Lynn's First SAK Mod Build
-
@Lynn LeFey said:
@Pablo O'Brien said:
Those pinheads (lol) don’t quite look like they’ll fit in the brushings.

I peened them WHILE the pin was in a bushing, so...

Toppskarven... it's all good.

I guess it will work then.

I just didn’t remember what it’s supposed to look like when peened to fit a brushing. :D
-
I would cut them off (and the bent part) and try again Lynn. I will look for some pics to show what you're after.
-
If I may offer some friendly advice...
When I modded my Compact to swap the corkscrew for a Phillips, I found that I got the best results when peening by using light taps and focusing on the center of the brass rod until it started to mushroom. Go slow and don't try to move the brass too much, too quickly. It will take you longer, yes, but the results will be better.
Once the rod starts to mushroom out, start to peen around the edges... again using light taps and not over-working the brass.
Another thing I did that you might want to consider is to get some larger diameter brass rods to practice on. I really feel like practicing peening the larger diameter rod helped me get better results when the time came to do it for real. Good luck, and keep at it!

-
@Lynn LeFey said:
Sorry for the delay in response.Yes, Lynn is indeed a she.
Second, there is SOME progress but my garage, where I'm doing the peening work, is unheated, and it's been very cold here the last couple days.
Still...
<a href="https://flic.kr/p/25PTknP" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/880/41236010821_fac6911391_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>I am not all that happy with my work. I think I slightly bent both pins in the process, so... (sigh). I'm not sure if i should proceed as is or cut off what I've done and try again.
Yeah, certainly the bottom one looks bent. I'm not sure why you'd do one side and not finish the knife though. After disassembly, cleaning and reassembly the peening is the easy bit.

-
So...
I'm sorry. I'm am profoundly angry and confused at this point. How the living SMURF are you supposed to peen F-ING ANYTHING on this F-ING tool? I have absolutely no idea how to peen the tool once assembled, because I'd just be banging the F-ING rod into a flat surface on the bottom side, and the layers, not being solidly held together, aren't going to support the pin staying straight any more than clamping it in a vice.
I absolutely see no way of doing this without peening one side before assembly.
I want you all to understand, I am LEGITIMATELY pissed at all of this at the moment. This was supposed to be fun. This is not fun. I am not having fun. This is not Lynn's 'I'm havng fun' face.

-
Have you tried wrapping the tool in tape to stop it flopping around when you hammer it?
Do you have some heavy metal thing to use as an anvil?Peening can be a smurf in the behind sometimes. :ahhh
-
@Pablo O'Brien said:
Have you tried wrapping the tool in tape to stop it flopping around when you hammer it?
Do you have some heavy metal thing to use as an anvil?Peening can be a smurf in the behind sometimes. :ahhh
To echo Pabs, an anvil will make your peening a lot easier Lynn. Do you have a flattish hammer you can use to peen on? Before Sparky hooked me up with a Vice with an anvil, I used to peen on my Estwing hammer - worked really well.
That way you are kind of peening both ends at the same time. What you're after is a mushroom shape on the pin - do one end, turn over and do the other, gently each time, and file the top so you are shortening the pin while 'filling' the bushing.
Use light 'strokes' of the hammer around the edges of the pin and you'll soon see a mushroom shape appear.
Once the pin is nice and tight inside the bushing and is filed level, I use a wide centre punch to finish with. This should ensure that the pin fills the bushing.
-
Sorry you're struggling Lynn. :(
As the others have said - are you using an anvil? I find that upsetting the rivet lightly with a few taps on both ends to retain the bushes and keep the pins in place helps, and lets me carry on with the peening without the bits going everywhere.
I use the flat side of the hammer to form the majority of the rivet, working around the edge of the rivet head as it forms until it's flush with the bushing. Then, if I need to tighten the pivot I'll switch to the ball side to enable me to get down inside the bushing. I don't us a punch to finish, as mine seem to be fairly flush. If you've got material left sticking up, you can file it off after peening. I use a 4 oz hammer with a fairly short handle, FWIW.
-
Dug up some old pics.


Get it started then add the bushing and continue, lots of little taps.


After fitting cut and file down the other side.

Now find something solid and flat to peen against.

The first one is allowed to be rough, the more you make the better you will get.

-
Thanks all.
I'll probably get back onto this project tomorrow.
-
the most :o in zoid's post is that he managed to cut something solid with the MP's replaceable wire cutters without them shattering into a thousand pieces :ahhh :D
-
Okay, so... long post coming.
This morning, i started off by lopping off the peening I'd done to the larger pins. Then I tried to assemble the tool, and got it about 95% assembled, was checking the functions and...
Heh... I put the scissors in upside down.

Fine... took it apart and ... couldn't get it back together. I was incapable of getting a tool in to snap the pieces under the spring after another spacer was in, so had been putting the tools in, with spring in place, layer by layer. First, the tools kept popping out from their tensioned position AND the center pin kept just falling out.
I gave up.
For a couple hours.
Then i had the idea of using a piece of wood as a sort of jig to hold the pins. THEN I had the idea of using binder clips to hold the tools together.
And...
<a href="https://flic.kr/p/24WVkA9" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/818/40659260464_408da3a546_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Then the tool started to come together.
Layer by layer... After the opener layer was the scissors...
<a href="https://flic.kr/p/25Y9C4h" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/816/41329525582_6e3fb6386f_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Then the file...
<a href="https://flic.kr/p/HUdvSQ" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/895/27501527128_7cafe16030_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
And (not pictured), the blade layer.
From there, I had a firm hold on all the tool layers, and wrapped it in electrical tape to hold everything together.
<a href="https://flic.kr/p/25Y9BXf" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/799/41329525232_45dc0336be_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I cut off the pins with the wire cutters of a Gerber MP600. Once out in the garage, I placed the bushings on the first pin and started peening.
<a href="https://flic.kr/p/HUdvLY" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/889/27501526788_fe63201822_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I peened all the pins just to the point where it was holding the tool together, and then started checking side to side play in the tools as I went.
<a href="https://flic.kr/p/25Y9BSA" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/819/41329524962_09a04ae4b5_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
There were several instances where I didn't cut the pins short enough (I guess better that than too short, huh?) and had to go back with the cutting wheel of my dremel to adjust and repeen.
I filed down the rough remains. I also tried using a hardened punch to dimple the ends of the pins, hoping to seat them better, but if this actually accomplished anything, I couldn't tell.
Finally, back in the house, and pressed the scales back on. When i removed them from the original knife, I bathed the knife in as hot of water as I could stand, hoping to soften the plastic of the scales to do minimal damage and allow them to just be press fit back on, and I don't know if it was that or just luck, but it worked. They are on solid with no wobble just from a press fit.
And here is it... A one-of-a-kind 'Grand Prix'.
<a href="https://flic.kr/p/HUdvHb" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/787/27501526568_7cb038cc44_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
It has the opener layer of an early 70s Huntsman, including '+ PAT' on the can opener, awl with no sewing eye, and inside sharpened edge on the cap lifter. It has the newish scissor layer, still has a screw at the pivot, but has backside parcel hook. I decided to use the newer scissors because they were the best available, and replacement springs are easier to find (and replace). It has the file layer from the Automobile Special, which also donated its scales. And it has the newer blade layer of the same Huntsman that donated its scissors, except I swapped the Corkscrew for the square shanked phillips with tin key of the Automobile Special.
I would have loved to keep the small clip-point blade of the older Huntsman, but I didn't want to go messing with mixing parts from different blade layers. I seem to recall Gareth mentioning that it's a BAD IDEA (tm).
So...
SMURF YEAH! I DID IT! :ahhh

-
Looking good! And that awl that work paid of [emoji854] nice work
[It's not failure if you learn something from it]
-
Great WIP pictures Lynn

Nice job

-
Nicely done Lynn !

-
Thanks all.
I think I managed to find every conceivable way to screw up at every single step, ruining a few liners during disassembly, failing on the initial peening, so wasting precious pin stock, assembling wrong.

It was absolutely a learning experience.

-
great mod Lynn
I like your jig. -
Nicely done Lynn

And some excellent jig work

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

