Spirit One-Hander
-
posting just to keep the thread alive so any new members know this is a recent project.
Hope Bob has the time to work on this, and doesnt run into too many difficulties, I know everyone is eagerly awaiting any developments.
-
i,d be very interested in seeing how this one pans out! :)
-
Thanks for the encouragement guys. I've not come up against any problems except lack of time.
(That, and my uncanny ability to start and half-finish several projects at once!)
I'll keep you posted.
-
Finally found some time this week after hours to work on a new knife blade. It's my first one ever, so I'm going really slow and being really careful. Believe it or not, every single one of those bumps and notches around the pivot on the RH end are critical. Remove too much material in the wrong place and the blade opens too far, or it doesn't lock properly, or it closes too far and wrecks the knife edge. It's definitely been a learning experience.
Next step (I think?) is too rough-in the knife edge bevel. Then it's off to heat treat, then polish up nice and shiny, then sharpen the edge properly.
This is all new to me, so if anyone has advice, please speak up!

-
Very nice work so far Bob!
Damn those precise Swiss Engineers huh? :P
Def
-
polish it up before it goes to HT .. to at least 240 grit MINIMUM.
You will thank me later ;).
looking good so far.
-
Have you gotten anywhere with the rivet issue yet?
Def
-
@J-sews said:
Next step (I think?) is too rough-in the knife edge bevel. ...if anyone has advice, please speak up!The next step is to make some for your friends at multitool.org! ...and one for me too!

-
Dunno why but I really dislike the shape of that blade. I think you should have gone for the shape LM have put on their charge/surge/wave tools, just my personal preference.
-
This shape is more akin to the OHT shape... gotta keep your mods at least partially traditional!
Def
-
-
Nice custom OHT... I wonder who belongs to that one! :P
So, where are the serrations on yours? You have to put on the serrations so everyone can complain about them then grind them off!

Def
-
Nice work J, still watching this thread with baited breath. Really hoping this works out - good to hear you're going slow - my mistake is always haste - and my engineer mates end up telling me smugly, over a pint, "Measure twice, cut once".
Not sure I would have gone for a OHT blade shape, but I respect your decision to keep it "pure" victorinox - classy.
-
I am just wondering how hard it will be to convince him to send it to me for "evaluation" when it's done! :D
Def
-
He already promised it to me :) It's a Michigan thing...
-
I wouldn't admit to that in public after the season the Tigers have had... but then I guess you guys are used to it! :P
Def
-
Well that just made my decision a WHOLE LOT easier!

PM me with your address when you get a moment Mike. ;)
-
Oh so now it's my fault you guys will never see a pennant? :P
Def
-
Dredging an old topic....
Gonna stay out of the sports thing other than, to
Def.. :PHow did this turn out Bob?

I've found that I used the blade on my wave more than I thought; by not having an easily opened blade on the spirit..
-
@Ice Tigre said:
How did this turn out Bob?
I've found that I used the blade on my wave more than I thought; by not having an easily opened blade on the spirit..
This project got set on the back burner for a few months while I was working on the Multitool.org multitool. I dusted it off last week and finished up the "soft" work on my knife blade. Now it's off to heat treat being hardened.
After that, all it will need is polished and sharpened. This isn't something I feel comfortable doing myself, I'd rather have it done by a pro. Does anyone have any recommendations?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
