Spirit One-Hander
-
@J-sews said:
Next step (I think?) is too rough-in the knife edge bevel. ...if anyone has advice, please speak up!The next step is to make some for your friends at multitool.org! ...and one for me too!

-
Dunno why but I really dislike the shape of that blade. I think you should have gone for the shape LM have put on their charge/surge/wave tools, just my personal preference.
-
This shape is more akin to the OHT shape... gotta keep your mods at least partially traditional!
Def
-
-
Nice custom OHT... I wonder who belongs to that one! :P
So, where are the serrations on yours? You have to put on the serrations so everyone can complain about them then grind them off!

Def
-
Nice work J, still watching this thread with baited breath. Really hoping this works out - good to hear you're going slow - my mistake is always haste - and my engineer mates end up telling me smugly, over a pint, "Measure twice, cut once".
Not sure I would have gone for a OHT blade shape, but I respect your decision to keep it "pure" victorinox - classy.
-
I am just wondering how hard it will be to convince him to send it to me for "evaluation" when it's done! :D
Def
-
He already promised it to me :) It's a Michigan thing...
-
I wouldn't admit to that in public after the season the Tigers have had... but then I guess you guys are used to it! :P
Def
-
Well that just made my decision a WHOLE LOT easier!

PM me with your address when you get a moment Mike. ;)
-
Oh so now it's my fault you guys will never see a pennant? :P
Def
-
Dredging an old topic....
Gonna stay out of the sports thing other than, to
Def.. :PHow did this turn out Bob?

I've found that I used the blade on my wave more than I thought; by not having an easily opened blade on the spirit..
-
@Ice Tigre said:
How did this turn out Bob?
I've found that I used the blade on my wave more than I thought; by not having an easily opened blade on the spirit..
This project got set on the back burner for a few months while I was working on the Multitool.org multitool. I dusted it off last week and finished up the "soft" work on my knife blade. Now it's off to heat treat being hardened.
After that, all it will need is polished and sharpened. This isn't something I feel comfortable doing myself, I'd rather have it done by a pro. Does anyone have any recommendations?
-
Paul Bos is the undisputed master of heat treating, but I don't know if he would take something like that on. I think he's pretty well a big time organization nowadays.
Other than that, I don't know of any that would be any better than any others.
Def
-
Heat treat I've got covered. It's the polish and sharpening that I could use some assistance with.
(actually, the polishing and sharpening is something I could learn to do myself. But never having done either before, I don't want to screw up all the work I've got into this blade up to now!) :P
-
Oh, well in that case, damned if I know! :P
You could try sending an email to Tom (Rotokid) as he's got all kinds of contacts that may be able to help out.
Def
-
Polishing can be as simple as a sanding pad and a range of wet/dry(use with wd40 for a faster even cut) sandpaper, from a grit close to the finish before heat treat, up to around 600 or 800 for a satin finish. At every grit change, change the direction you sand by 90deg...
Then you can buff with a dremel, or some flitz and a soft cloth.
If you didn't find somebody willing to do it, and still need someone, drop me an e-mail...
:)
G.
-
now I've read this and got excited and it's not done yet!!! how can I enjoy my christmas....

-
@WhichDawg said:
now I've read this and got excited and it's not done yet!!! how can I enjoy my christmas....
Ouch! That pokey stick is sharp! :o
Okay, okay, I'll get it done next week. There won't be much going on at work between the holidays, so I should be able to commandeer one of the grinders and get this baby finished.
-
now I've read this and got excited and it's not done yet!!! how can I enjoy my christmas....

Ouch! That pokey stick is sharp! :o
Okay, okay, I'll get it done next week. There won't be much going on at work between the holidays, so I should be able to commandeer one of the grinders and get this baby finished.
:D many will be happy! and for the record, you do really nice work mister, we have a nice mill and press and constructing a new Plasma CNC table, I will be trying some of your mods bro! your in MI ever have shermans ice cream in South Haven? it's the best ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
