PowerPint Overview Mighty Little MT
-
@Sam Lim said:
I have one on the way from KC as well but probably another 2 to 3 weeks wait before its reaches me on the other side of the globe. I am liking the size so far. Thanks for the pics and the overview GLBM!

You're quite welcome, Sam Lim!

It also seems like a tool with mod potential. I removed a pivot pin to stretch the clip out a bit for my thicker jean pocket and the screw and threads looked good. They are fine threads, but screw in deep. The torx head pin didn't act like it was going to strip out when breaking the loctite(some kind of thread glue I am not familiar with).
I hope the one you receive is as good as the on I received.
Another good bit of info that is good to hear as I'm thinking about removing the clip, it looks a bit strangely angled and also in general I'm not really a pocket clip person, I'd rather carry it in the pocket especially now that I have caddies. This way the removal will be no problem.
One thing to note is that the pin extends into the clip's mounting hole, so you'll need a washer to take up the space the clip did on the pivot pin. The washer will ens up on the outside of the frame, which isn't a big deal. You could grind the pin down, but a washer gives you the option to put the clip back on.

-
-
-
I received mine today!! It came much faster than expected. And the package was really, small.
Out of package, I have to say I am not too pleased with what I have received.Having fortunately/unfortunately handle all the past 2017 models, to be honest, this was expected. I am sorry GLBM and SOG fans..
These are the problems I have...
-
The pliers I have received are misaligned at the tip. I really hate this when it new out of package. I have never had this problems with any of my SOGs before. So this time I am really disappointed.
-
I had very bad tool clumping on one side of the handle. When I pull out the serrated blade, everything else comes out with it. Took a closer look and realise the pivot is stuck with the blade and is moving along. I actually took apart that side of the handle immediately. I was right. The pivot hole of the blade is stuck with the pivot. Its pivot hole is somehow smaller than the rest of the implements. So whoever put this together simply does not care and probably hammered the pivot in. I had to do some filing to sort this out.
-
My serrated blade is slightly warped. Scissors crosses over too much, giving so much resistant that its almost unusable.
-
The back end of the tools that rubs against the locks are very rough. Making it very gritty when opening the tools.
-
Washers between the tools are very poor quality and mostly deformed but probably because they are so thin.
-
Some parts on the handle frame are finger slicing sharp..
There are the rants I have using eyeball and hand-ons inspection. More observations to come when I start using them.
Returning is not an option as I am on the other side of the world and paying for shipping simply does not make sense...
Having said all of the above, most problems are user correctable other than the the pliers misalignment...... I am still liking this tool at the moment and looking forward to using it!
Oh btw, Lynn, if you are reading this, this is a left hand scissors.....

-
-
I promised some photos, but they turned out pretty bad because of the lighting, they are too yellowish and dark or overexposed and lacking details, so I'll try to make some better ones tomorrow in natural lighting. I included some anyway.
My observations after playing with it for half a day now: there is some tool clumping, but on mine definitely not to the extent as in Sam Lim's case, and I suspect this is by design, as the inner tools come up a bit with the longer tool on the side, but only the ones on that particular side, my guess is to make the opening easier, as they're pretty hard to reach even with my smaller fingers. As for the gritty opening: the bottoms have machining marks, lines, yes, but I see nothing out of the ordinary on mine, I've seen similar marks on my Rebar and Juice too, and these will definitely smooth out with time and use.
My blades are perfectly okay, nothing to note there, but I agree about the scissors, it needs significant amount of force to operate, but hopefull it will break in. I particularly like that you can pop off the top arm from the springbar, probably for easier maintetnance, sharpening. The plier tips don't align perfectly, but for me that 0.1 mm makes no difference, insignificant and I expected something like that.
I'm not too fond of the pocket clip, I took that off, and for me the stonewash finish makes the tool look a bit cheaper than it is, but the surface will definitley age and get a bit more uniform and polished. My biggest gripe is the "file", even though I was prepared for it being bad, it's even worse than I expected. It's laughably bad, unusable. The crosscut side reluctantly filed fingernail, but that's all. It's just a metal bar, a complete waste of tool space. I wish someone would make an aftermarket file for the PowerPint!

The awl is scary sharp and pointy, the drivers are okay, the bit holder works as intended, but the protractor is just a gimmick, I have close to so called 20/20 vision and even in daylight I couldn't make out the markings, even with the Swisschamp's magnifier it took a while to recognize the numbers.
That's all for now.




-
Thank you Exeter and Sam Lim for posting about your Pints. That is absolutely why I didn't call my thread a review(just an overview). I had a sneaking suspicion that QC problems would have a greater impact in regards to the way this tool is constructed. The tolerances are MUCH tighter than any of their other tools.
I will not write a review now that I know they couldn't make this tool consistently as well as the one I received.
-
I think the tool clumping are unavoidable. Since they are just normal washers. Nothing "special" like Gerbers or some leatherman series that are designed for that purpose. I am actually fine with clumping. But what happened in my case was not suppose to happen..
Sog.BTW, anyone notice there isn't a proper flathead screwdriver on board...
my cap lifter will turn into one soon.. -
@Sam Lim said:
I think the tool clumping are unavoidable. Since they are just normal washers. Nothing "special" like Gerbers or some leatherman series that are designed for that purpose. I am actually fine with clumping. But what happened in my case was not suppose to happen..
Sog.BTW, anyone notice there isn't a proper flathead screwdriver on board...
my cap lifter will turn into one soon..I did mention that you'll need to pocket a few bits with the Pint if you need more than a "jeweler's flat driver."

-
@Sam Lim said:
I think the tool clumping are unavoidable. Since they are just normal washers. Nothing "special" like Gerbers or some leatherman series that are designed for that purpose. I am actually fine with clumping. But what happened in my case was not suppose to happen..
Sog.BTW, anyone notice there isn't a proper flathead screwdriver on board...
my cap lifter will turn into one soon..I did mention that you'll need to pocket a few bits with the Pint if you need more than a "jeweler's flat driver."

Ya.. I missed that..
This is quite a strange MT after playing with it for a while.. It feels like a shrunk down power grab.. Rather than a new design... Strange... -
@Sam Lim said:
@Sam Lim said:
I think the tool clumping are unavoidable. Since they are just normal washers. Nothing "special" like Gerbers or some leatherman series that are designed for that purpose. I am actually fine with clumping. But what happened in my case was not suppose to happen..
Sog.BTW, anyone notice there isn't a proper flathead screwdriver on board...
my cap lifter will turn into one soon..I did mention that you'll need to pocket a few bits with the Pint if you need more than a "jeweler's flat driver."

Ya.. I missed that..
This is quite a strange MT after playing with it for a while.. It feels like a shrunk down power grab.. Rather than a new design... Strange...Do you still have a PowerGrab? I am not getting that feeling...yet.
The PowerGrab seems(to me anyway) more akin to the PowerPlay than anything else. Maybe I am missing something?
Edit:
It does seem like a decent new modding platform. Any ideas for modding the Pint yet, Sam Lim?
-
@Sam Lim said:
@Sam Lim said:
I think the tool clumping are unavoidable. Since they are just normal washers. Nothing "special" like Gerbers or some leatherman series that are designed for that purpose. I am actually fine with clumping. But what happened in my case was not suppose to happen..
Sog.BTW, anyone notice there isn't a proper flathead screwdriver on board...
my cap lifter will turn into one soon..I did mention that you'll need to pocket a few bits with the Pint if you need more than a "jeweler's flat driver."

Ya.. I missed that..
This is quite a strange MT after playing with it for a while.. It feels like a shrunk down power grab.. Rather than a new design... Strange...Do you still have a PowerGrab? I am not getting that feeling...yet.
The PowerGrab seems(to me anyway) more akin to the PowerPlay than anything else. Maybe I am missing something?
Edit:
It does seem like a decent new modding platform. Any ideas for modding the Pint yet, Sam Lim?
I sold off the power grab soon after I got it.. Felt that its too bulky. I remember when I first got the power grab, when I open the handle and saw that pliers head, that left a deep impression in me. That thing is beautiful beyond words..
Off my mind, juice/squirt tools look quite promising. Pivot holes looks quite the same I think.. Adding in the package opener from dime will be a great asset I feel. After taking it apart yesterday..
I might pull off another stunt here with a unlocking lever again. The one on the ST work really well. Not liking the lock on this one..
-
Looking forward to seeing what you come up with.

Edit: Just saw your edit, Sam Lim.
That plier head is the main reason I kept mine, so I know what you mean. The Grab plier head is possibly the most beautifully machined plier head ever made. :ahhhOn another note, I am curious to know if the tool tangs on the Pints You and Exeter got are rougher looking than mine. I hope this photo shows it clearly. It feels really smooth, so I didn't give it any thought, but in macro, I can see it.
Does yours look rougher? Does it feel rough to the touch?
-
For anyone not sure what Sam and I are talking about in regards to the PowerGrab plier head(Grab left and PAD right).


-
@gerleatherberman said:
For anyone not sure what Sam and I are talking about in regards to the PowerGrab plier head(Grab left and PAD right).
GLBM, you and I know the picture doesn't do it justice. I honestly haven seen anything that wows me that much after the PG.. Now u are making me wanting one again... :ahhh
Regarding the backside of the tool, some are smooth, some rough. Enough to feel the "gear" effect when pulling it back..
-
@Sam Lim said:
GLBM, you and I know the picture doesn't do it justice. I honestly haven seen anything that wows me that much after the PG.. Now u are making me wanting one again... :ahhhRegarding the backside of the tool, some are smooth, some rough. Enough to feel the "gear" effect when pulling it back..
Had to try. People might think we're nuts saying the PowerGrab did something excellent.

Thank you, Sam!
It'll be interesting to see if that issue gets worse on newer Pints as tooling at the factory starts to wear out in the future.
-
@Sam Lim said:
GLBM, you and I know the picture doesn't do it justice. I honestly haven seen anything that wows me that much after the PG.. Now u are making me wanting one again... :ahhh
Regarding the backside of the tool, some are smooth, some rough. Enough to feel the "gear" effect when pulling it back..
Had to try. People might think we're nuts saying the PowerGrab did something excellent.

Thank you, Sam!
It'll be interesting to see if that issue gets worse on newer Pints as tooling at the factory starts to wear out in the future.
Who isn't nuts over here...

-
@gerleatherberman said:
Looking forward to seeing what you come up with.
Edit: Just saw your edit, Sam Lim.
That plier head is the main reason I kept mine, so I know what you mean. The Grab plier head is possibly the most beautifully machined plier head ever made. :ahhhOn another note, I am curious to know if the tool tangs on the Pints You and Exeter got are rougher looking than mine. I hope this photo shows it clearly. It feels really smooth, so I didn't give it any thought, but in macro, I can see it.
Does yours look rougher? Does it feel rough to the touch?On mine they look like this. There are machining marks, and can be felt when opening, definitely not buttery smooth, but wouldn't call it rough either.

-
Also, future owners be aware that the scissors on the PowerPint, although require quite some force to operate, are only good for threads, a couple of layers of normal printer/newspaper, thin zipties, thin regular cardboard. I tried it on corrugated cardboard and it failed miserably. See on the photo: the abandoned cut was made with the PP, the rest for comparison with the same piece of cardboard.
EDIT: Based on the size of the scissors, maybe a Squirt PS4 would be better for comparison, but I wouldn't dare to have a go at cardboard like this with that, so looking at like that, it's a win for the PP.


-
-
@Sam Lim said:
Try cutter with your left hand. This is a pair of left handed scissor like I said before earlier.I, am, serious.
Btw, the design of the scissors are off. The handles are too short to give it any kind of proper leverage.
Well, I did just that, but saw no difference, it just chewed on the cardboard, it's too much for it. And let me add that I'm ambidexterous, or mixed handed to be precise, so my left is pretty much the same in strength and dexterity as my right, so that variable can be ruled out. For the sake of the experiment, I tried it with my right hand upside down, with the moving arm facing downwards to my pointer finger, but no difference either.
Maybe you scissors are better made, or your hand/fingers are stronger.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login
