Screwdriver bit sets
-
There is a thread here: /topic/76901
on the subject with a link to Etsy:
https://urbanedcsupply.com/products/apex-5-bit-tag
Sorry about the small size of the picture.
-
@smiller43147 said:
There is a thread here: /topic/76901
on the subject with a link to Etsy:
https://urbanedcsupply.com/products/apex-5-bit-tag
Sorry about the small size of the picture.I use the Leatherman Bit Adapter and Bits with my Spirit X and it all fits nicely in my Skinth and I have been carrying the Centerdrive bits and tool itself also nicely on the Skinth.
But I also really like this set that I get with a Craftsman Ratcheting Screwdriver as it holds a lot of bits tightly but is too big for my EDC Skinth too?
It does fit in a Magnum though!


Sent from my iPhone using Tapatalk
-
I bought the double end bit set for the crunch specifically. Though I do not use them that often...

-
I carry a set of the leatherman flat bits in my edc.
-
I carry my bit kit with me everyday I use a ganzo g202 as it's all I can afford at the moment. I like the kit because it kits nicely in the sheath behind the multitool and as they're standard bits if I ever break or lose one I cab replace it easily

Sent from my HTC Desire 530 using Tapatalk
-
Battling with concrete infested screw heads I went through no less than 4 torx bits over just some 40-50 screws or so. I truly appreciate that they were totally standard and will thus be easy and inexpensive to replace.
(And I've finally found an application were torx heads are worse than the simple slot).
From a EDC viewpoint I only carry bits if they are stored inside the tool itself.
-
Let's expand a bit on this then- what bits do you carry, which ones do you use most, and which ones do you wish you had or miss when they aren't there?
Def
-
My Doc Allen is in my pack every day. Right now, I've got a LOT of driver bits in there, as part of an ongoing survey. If I use a bit, I'll put a mark on the carrier. Around this time next year, I'll look at the marks and keep those, along with the basic bits (small, medium, large straight, 1 & 2 phillips, 1 & 2 robertson, a couple of torx and hex bits that my firearms use) and the 3/32" punch and x-acto blade holder. This started when a couple years ago, after needing some security bits on a couple of occasions, I through a small set into my car. And haven't touched them since. So... figure out what I need.
-
I carry the Gerber bit kit with my MP400 usually;

I replaced the hex bits with a Phillips 00, Phillips 000, and Torx 10. Seems like the bits I use the most are the Phillips 2 and larger flathead, so I'd probably miss them the most.
-
If I wanna go light-weight I carry my LM Wave "naked". But if I suspect duty might call, the Wave gets in the sheath where the bit extender and a single slab (I hope I'm using the right word here) of bits await him. The bits do make the sheath bulkier, yes, but this configuration is not my EDC anyway, so no problem.
-
Well, this might not work everywhere, but in my neck of the woods Robertson is unknown, so I've taken those out of the trimmed-down LM kits for the ST300VX and Surge-R. As said neck is in addition thoroughly metricised, I've also taken out the various inch-based hex bits except for the one with 6mm and 1/4". I'd have to check what exactly remains. These fit on one card.
-
Right...
(bombastically clears table with forearm)... this is the set I use/carry the most - most of the bits, that have been collected over time, are PB Swiss Tool ones... I say over time because they cost a bloody fortune, but I love the pretty colours and they're excellently engineered... and last for yonks (I've yet to have shattered one, although on rare occasions some work colleagues somehow have!
)
When travelling, like Ironraven, I carry my Doc Allen Versathingy with assorted bits (including a Robertson bit) - which I think is absolutely superb and one of the best tools of its kind(?) out there. I really can't rate it highly enough. People always poo-poo the high-torque claims made about it, but it's true, it has absolutely smurf-loads of torque potential!!! I've removed 4" Pz3s with it... try doing that with a Wave (and watch the bit holder open up)! :ahhh

... flops on chair and relaxes...
-
When EDC'ing my surge, I keep an extra box leather sheath next to the Surge sheath for the full 2-card of flattened bits and orher bayonet type jig saw blades. Anything to keep from making the Surge sheath protrude outwards too much
-
LM and Vic

-
I was carrying those leatherman flats, there still in my large carry bag, but I’ve kinda lowered my edc down to a sak, anything more then a leatherman gets carried and I should switch those flats over.
JR -
i carry a leatherman bit kit in my surge sheath as a back up, but usualy at work i also carry a standard bit kit in a seperate sheath (a victorinox SAK sheath) where i also carry a voltage tester.
this way i can leave it on my desk if i think i wont need it but i still have the flat bits incase something comes up.
and due to murphys law, the times when i usualy think that i wont need them are the times that i probably will need them!

-
I haven't carried a leatherman bit set (but own one) but I do carry the victorinox ratchet set.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



No , just my bit sets , I already carry a 60 pound tool bag 