Screwdriver bit sets
-
I carry a set of the leatherman flat bits in my edc.
-
I carry my bit kit with me everyday I use a ganzo g202 as it's all I can afford at the moment. I like the kit because it kits nicely in the sheath behind the multitool and as they're standard bits if I ever break or lose one I cab replace it easily

Sent from my HTC Desire 530 using Tapatalk
-
Battling with concrete infested screw heads I went through no less than 4 torx bits over just some 40-50 screws or so. I truly appreciate that they were totally standard and will thus be easy and inexpensive to replace.
(And I've finally found an application were torx heads are worse than the simple slot).
From a EDC viewpoint I only carry bits if they are stored inside the tool itself.
-
Let's expand a bit on this then- what bits do you carry, which ones do you use most, and which ones do you wish you had or miss when they aren't there?
Def
-
My Doc Allen is in my pack every day. Right now, I've got a LOT of driver bits in there, as part of an ongoing survey. If I use a bit, I'll put a mark on the carrier. Around this time next year, I'll look at the marks and keep those, along with the basic bits (small, medium, large straight, 1 & 2 phillips, 1 & 2 robertson, a couple of torx and hex bits that my firearms use) and the 3/32" punch and x-acto blade holder. This started when a couple years ago, after needing some security bits on a couple of occasions, I through a small set into my car. And haven't touched them since. So... figure out what I need.
-
I carry the Gerber bit kit with my MP400 usually;

I replaced the hex bits with a Phillips 00, Phillips 000, and Torx 10. Seems like the bits I use the most are the Phillips 2 and larger flathead, so I'd probably miss them the most.
-
If I wanna go light-weight I carry my LM Wave "naked". But if I suspect duty might call, the Wave gets in the sheath where the bit extender and a single slab (I hope I'm using the right word here) of bits await him. The bits do make the sheath bulkier, yes, but this configuration is not my EDC anyway, so no problem.
-
Well, this might not work everywhere, but in my neck of the woods Robertson is unknown, so I've taken those out of the trimmed-down LM kits for the ST300VX and Surge-R. As said neck is in addition thoroughly metricised, I've also taken out the various inch-based hex bits except for the one with 6mm and 1/4". I'd have to check what exactly remains. These fit on one card.
-
Right...
(bombastically clears table with forearm)... this is the set I use/carry the most - most of the bits, that have been collected over time, are PB Swiss Tool ones... I say over time because they cost a bloody fortune, but I love the pretty colours and they're excellently engineered... and last for yonks (I've yet to have shattered one, although on rare occasions some work colleagues somehow have!
)
When travelling, like Ironraven, I carry my Doc Allen Versathingy with assorted bits (including a Robertson bit) - which I think is absolutely superb and one of the best tools of its kind(?) out there. I really can't rate it highly enough. People always poo-poo the high-torque claims made about it, but it's true, it has absolutely smurf-loads of torque potential!!! I've removed 4" Pz3s with it... try doing that with a Wave (and watch the bit holder open up)! :ahhh

... flops on chair and relaxes...
-
When EDC'ing my surge, I keep an extra box leather sheath next to the Surge sheath for the full 2-card of flattened bits and orher bayonet type jig saw blades. Anything to keep from making the Surge sheath protrude outwards too much
-
LM and Vic

-
I was carrying those leatherman flats, there still in my large carry bag, but I’ve kinda lowered my edc down to a sak, anything more then a leatherman gets carried and I should switch those flats over.
JR -
i carry a leatherman bit kit in my surge sheath as a back up, but usualy at work i also carry a standard bit kit in a seperate sheath (a victorinox SAK sheath) where i also carry a voltage tester.
this way i can leave it on my desk if i think i wont need it but i still have the flat bits incase something comes up.
and due to murphys law, the times when i usualy think that i wont need them are the times that i probably will need them!

-
I haven't carried a leatherman bit set (but own one) but I do carry the victorinox ratchet set.
-
I rarely ever wear a multitool on the belt, so for multitools I only carry bits in the tool itself.
If I know I need a bit somewhere I typically grab one of the ones pictures below, a Wera hard plastic kit, or some cheap sacrificial bit sets. Left to right I think it is a set of Swisstool bits, supplemented by a few loose ones in the middle there. Great bits, useless plastic holder.
Then the red one is a great little Teng tool bit set with ratchet. So-so bits, but cheap to replace at least. Nice little ratchet. I used to have one with same size but some sockets instead of some of the bits - that one was nice too.
In the middle there are 4 hex sockets with rounding. When you need those then not much else will do - on the flip side I avoid using them unless I have to in order to keep them around for those occasions.
The bits with the blue band in the middle are actually cheap but very nice. The small grooves on the tips give very good grip on screws, and the steel is not some typical black softish rusty thing.
The black and yellow short handle with 4 bits is my go-to little portable screwdriver. Inexpensive, portable, good grip and good bits. What is not to like?
Then to the right there is a plastic fantastic handle with 12 precision screwdrivers in the handle. The bits are good - the handle is not. Still, I find myself taking that if need those kind drivers for a quick fix somewhere.
And then there is a soft pouch Wera set with long drivers. Very nice, good bits, and on the expensive side. Still the one I use the most of these by far.

-
When I'm doing auto/house work I usually have a mixed batch of bits in an old bit holder(is that the word?) I stuff into my sheath behind my SOG powerlock. Not paying $20 for bits I already have

Honestly I think that a flathead and Philips are all I really need for edc I have a craftsman top box in the Jeep if I need more variety of bits.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



No , just my bit sets , I already carry a 60 pound tool bag 