Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Powernoodle Day 1

The paper cut test was about a 7/10 for me. The blade seems sharp, but I was getting some tearing as well.First impression of the PowerAccess Deluxe is that its Chinese construction is apparent. It has a somewhat cheapy feel to it, which is magnified a little due to the thinness of the main blade (edge to spine dimension) and other thin tools. I think I could break off the main blade with my bare hands if I tried. The tools can be accidentally deployed past 180 degrees if the lock does not engage, which lends to the cheap feel. Deployment of the plier is smooth and what you come to expect from SOG, and the gear pivot is at the heart of the MT. I like the real, 3D phillips driver with long shank. For me this is an important component which is lacking on the Wave, etc. The saw is short and takes a good amount of effort to get through a 1" branch, but its far better than not having a saw with you. The PowerAccess Deluxe has a stonewashed finish. The PowerLock and PowerAssist series have a polished finish which may add a subjective level of quality to the MT, but this presumably would add to the cost. And lets be honest - the file on the PAD is of low quality. The single-cut side is almost smooth and will not shape a fingernail. The opposite and double-cut side is not much better. But I'll try it on some PVC or other material and see how it goes.

Polished finish on the PowerAssist.At $69.99 in the U.S., the PowerAccess Deluxe is priced about right relative to the competition, and you get what appears to be a decent sheath (have to keep an eye on the velcro) and the small driver set. My lifestyle (working from a laptop at my kitchen table) does not require Torx bits on the belt, so I will mostly - though not exclusively - carry the PAD in the vertical pocket of my usual 5.11 Taclite Pro pants without the sheath and driver set. I can carry a full size MT in this manner without noticing it, because the pocket is high enough up the leg that the MT does not flop around.
I own several SOG MTs, along with maybe a couple of dozen SOG folders and fixed blades, and am a fan of the company. The Chinese construction, though not up to the competition, has never compromised function and I expect a good 30 days out of the PAD.
-
Thanks powernoodle, this prompted me to take a closer look at the saw. Not sure this is intentional - there are what appear to be small curls of steel in places where some facets of each of the teeth meet. I have attempted to capture what I mean below. I have yet to test whether that impairs function.


Sent on my SM-G930F with Tapatalk
-
I believe things like that disappear the first time you use the saw?
I see them to a lesser extent with unused SAK saws. -
I just checked mine and it hasn’t got anything like that


-
Me neither, but I have used my PAD's saw as well. I think that DT just got a sub-optimal grind job on his saw.
*
Note how the saw teeth on the PowerAssist Deluxe (left) are canted slightly toward the MT, whereas the teeth on the Swisstool Spirit (right) are not canted. This configuration presumably makes the PAD cut only on the pull stroke, with the Spirit cutting in both directions. Just a guess.* -
Maybe mine did... let's see what happens after I've used the saw to down the tree in my back yard.
Jokes aside, saw and file (did I say file?) seem shortish...
-
I just want to make everyone aware
that when they are testing the cutters
On the pliers that they are only <u>Soft Cutters </u>
As you can see in the pic
So personally I wouldn’t try to cut fencing etc..

-
Yeah, W, I saw that on the box yesterday when my PAD arrived. Its a bummer when you ding up your cutters, especially when they can't be replaced. In my view, any MT cutters "should" be able to take down hard wire (nail, fence), but that is not always the case.
The PowerLock has a hard wire cutter: https://www.sogknives.com/powerlock.html
-
Is brass rod (under 3mm/ 1/8” ) considered “hard”?
-
I agree you should be able to cut a nail or a fence etc
But I don’t want to try it as it would not be covered under warranty
And this is my first SOG so don’t know how good they are
-
I have left Chris@SOG a email
So hopefully I will get a reply
-
@Don Pablo said:
I believe things like that disappear the first time you use the saw?
I see them to a lesser extent with unused SAK saws.Yup - they did
(had to help a little at the very tip by way of judicious application of an X-Acto blade).Saw works OK but it's short. I think it could have been made a bit longer, there is about 9 or 10 mm spare space in the handle. Makes one wonder...
-
Since I have several SOG MTs, and am not worried about destroying this one, I used the PAD to cut a "10d" or "10 penny" cement-coated general carpentry/framing nail. I had to apply a lot of pressure, so much that it hurt my hand and I had to glove up, but it cut the nail with no problem. The compound leverage pivot surely helped in this regard, and I consider it the best feature on any SOG MT. I used the "hard wire" portion of the cutter, closest to the pivot, though SOG does not call it that. No damage to the "soft wire cutter", and no deformation or loosening of the cutter/head/pivot. [Edit: see below; the PAD does have a hard wire cutter.]
A 10d nail is 9 gauge and 0.148" or 3.76 mm at the shank.
Why cement coated? "Friction heat from driving the nail softens the cement coating and causes the nail to adhere to wood more firmly." https://www.westlakehardware.com/frequently-asked-questions/what-is-the-advantage-of-cement-coated-nails/
So I say it passed this test. My dynamic rating of the PowerAccess Deluxe went from 4/10 to 5/10.



-
Nice one powernoodle

I thought you had damage to the pliers :ahhh
But checked my PAD and it has the same cut out near the pivot
Never noticed that before, I take it that’s the hard wire cutter
-
On the website, it shows that the PowerAccess Deluxe has a soft and a hard wire cutter. Scroll down to the specs table. So it looks like the box just doesn't set out all of the specifications.
-
Excellent find powernoodle

This is from the SOG website
TOOL COUNT: 21
1 1/4" Driver
2 Awl
3 Blade (Fully Serrated)
4 Blade (Straight Edge)
5 Bottle Opener
6 Can Opener
7 Chisel
8 File (3-Sided)
9 Flat Screwdriver (Medium)
10 Flat Screwdriver (Small)
11 Gripper
12 Hex Bit Driver (1/4")
13 Hex Bit Kit
14 Jewelry Driver
15 Needle Nose Pliers
16 Phillips Screwdriver
17 Protractor
18 Ruler
19 Wire Cutter (Hard)
20 Wire Cutter (Soft)
21 Wood Saw
-
The box also shows a wire crimper (see #18 in post 86), that is not shown on the website. Intrigue!
-
@powernoodle said:
The box also shows a wire crimper (see #18 in post 86), that is not shown on the website. Intrigue!Excellent

Check out the pic to see what we are talking about
I don’t know what to say ???
I just can’t work out why they did that

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login