Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Excellent find powernoodle

This is from the SOG website
TOOL COUNT: 21
1 1/4" Driver
2 Awl
3 Blade (Fully Serrated)
4 Blade (Straight Edge)
5 Bottle Opener
6 Can Opener
7 Chisel
8 File (3-Sided)
9 Flat Screwdriver (Medium)
10 Flat Screwdriver (Small)
11 Gripper
12 Hex Bit Driver (1/4")
13 Hex Bit Kit
14 Jewelry Driver
15 Needle Nose Pliers
16 Phillips Screwdriver
17 Protractor
18 Ruler
19 Wire Cutter (Hard)
20 Wire Cutter (Soft)
21 Wood Saw
-
The box also shows a wire crimper (see #18 in post 86), that is not shown on the website. Intrigue!
-
@powernoodle said:
The box also shows a wire crimper (see #18 in post 86), that is not shown on the website. Intrigue!Excellent

Check out the pic to see what we are talking about
I don’t know what to say ???
I just can’t work out why they did that

-
PE blade on a4 was mediocre. Not as sharp as their dedicated knives. I suspected it wouldn't be very good from just feeling the edge.
SE blade did exactly what I expected. Tore the paper most of the time.Disassembled a typewrite for repair work and used the jeweler's driver to remove key set screws. No issue there.
Nice to see the cutters work correctly. I am hesitant to cut nails with MT cutters. Galvanized bailing wire is usually the the hardest thing I cut with MT cutters.
Thank you for doing that, PN. :)


-
The PE Blade is really sharp on my PAD
I can even shave hairs off my forearm
-
Day 1
I was able to cut post-it note paper with the PE blade on my Poweraccess, but it required light-medium sawing motion and sometimes ripped the paper. I should probably sharpen it.
-
I stropped mine on leather and it helped a bit. Maybe it is similar to the saw issue DT had, where excess metal exists from the machining process. I should have checked under magnification first, but maybe you can Pablo? Just to see if there is a burr on the apex.
-
At least that issue I have not found on my PE blade even under mag. There may be differences in QC...
Meanwhile we're on
**Day 2 **
... where the PAD sees itself detailed to light gardening duties

But first, a beauty shot. The roses are doing really well this sprummer.
Next are various stray branches succumbing to the forceful action of the wire cutter and saw, respectively. The former's compund leverage made short work of the admittedly thin branch, and it can easily accommodate slightly thicker branches (up to wire cutter blade width, I guess). For thicker branches the latter does a good job, but sawable thickness is a tad limited due to its shortness. I suspect SOG have decided to forgo lengthening the PA saw just for the PAD, but unless Chris chimes in, I guess this will remain speculation.




Sent on my SM-G930F with Tapatalk
-
Powernoodle Day 2
*
The PowerAccess Deluxe rides easily in the vertical pocket of 5.11 Taclite Pro pants.* -
Day 2
As everyone was talking about the saw yesterday
I used the saw in the woods to cut a ivy vine as
These are killing our trees
I found one that was nearly 65mm / 2.5 inches
I would say that that is it’s limit
I don’t know why the saw is so short ?
Apart from that it is nice and sharp and cuts good



-
you are all doing very good so far!
I agree that the tool has some issues but can't say I'm surprised given SOG's new strategies and direction, hopefully the tool will get to the end of all your challenges! 
As for the wire cutters, the SOG has a hard wire cutter but I managed to dent my Powerlock cutting braided wire (relatively thin, 5 strands).

I cut it with lots of effort, and while I originally placed the wire in the hard cutting notch it must've slipped out of it because it was too large for the notch, this I dented the normal softer cutting area


Now I admit I should've been more careful but I really wasn't expecting that
-
That’s a shame TP :ahhh :ahhh
Have you got a pic of the braided wire you cut
-
+1!
Side note on the protractor: on my PAD it is almost useless. From eyeball estimates I conclude the indices on the "30/60/180°" sides are off by tens of degrees and the indices do not align with the index on the handle, probably due to misprinting of the indices and/or misdrilling of the hole by which each hinge plate is fixed to the pivots. The "45/90/180°" sides are a bit better. When one index is at the 45° mark the other one is at 30°...

-
These - or similar - are the only hard wire cutters I trust not to deform. I'm almost surprised when MT cutters don't deform. They just are not made to the same hardness and precision as the real thing.
-
Day 2. Tried the saw out on some 1" dowels. The shape of the saw was good for this type of cutting. Not too difficult to push and pull, with the most cutting done on the pull stroke. It does remove material on the push as well, just not nearly as much.
The large teeth didn't try to clog at any point cutting six of the dowel lengths. On the flip side, the large teeth can(and did) cause hand fatigue rather quickly. :ahhh
-
Nice start, guys. Eager to join you in a couple of days!
Sent from my iPhone using Tapatalk
-
Thanks Nix

Have a safe trip and can’t wait to have you joining us
-
Powernoodle Day 3

-
Day 3
Today I had to adjust the fan in the downstairs toilet
It stays on for 30 minutes after you leave the toilet
Which is to long :ahhh
So today I used the jewellers driver
to turn the adjuster down to 10 minutes
The length of the driver helped as the adjuster is set far back in the fan



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login