Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
At least that issue I have not found on my PE blade even under mag. There may be differences in QC...
Meanwhile we're on
**Day 2 **
... where the PAD sees itself detailed to light gardening duties

But first, a beauty shot. The roses are doing really well this sprummer.
Next are various stray branches succumbing to the forceful action of the wire cutter and saw, respectively. The former's compund leverage made short work of the admittedly thin branch, and it can easily accommodate slightly thicker branches (up to wire cutter blade width, I guess). For thicker branches the latter does a good job, but sawable thickness is a tad limited due to its shortness. I suspect SOG have decided to forgo lengthening the PA saw just for the PAD, but unless Chris chimes in, I guess this will remain speculation.




Sent on my SM-G930F with Tapatalk
-
Powernoodle Day 2
*
The PowerAccess Deluxe rides easily in the vertical pocket of 5.11 Taclite Pro pants.* -
Day 2
As everyone was talking about the saw yesterday
I used the saw in the woods to cut a ivy vine as
These are killing our trees
I found one that was nearly 65mm / 2.5 inches
I would say that that is it’s limit
I don’t know why the saw is so short ?
Apart from that it is nice and sharp and cuts good



-
you are all doing very good so far!
I agree that the tool has some issues but can't say I'm surprised given SOG's new strategies and direction, hopefully the tool will get to the end of all your challenges! 
As for the wire cutters, the SOG has a hard wire cutter but I managed to dent my Powerlock cutting braided wire (relatively thin, 5 strands).

I cut it with lots of effort, and while I originally placed the wire in the hard cutting notch it must've slipped out of it because it was too large for the notch, this I dented the normal softer cutting area


Now I admit I should've been more careful but I really wasn't expecting that
-
That’s a shame TP :ahhh :ahhh
Have you got a pic of the braided wire you cut
-
+1!
Side note on the protractor: on my PAD it is almost useless. From eyeball estimates I conclude the indices on the "30/60/180°" sides are off by tens of degrees and the indices do not align with the index on the handle, probably due to misprinting of the indices and/or misdrilling of the hole by which each hinge plate is fixed to the pivots. The "45/90/180°" sides are a bit better. When one index is at the 45° mark the other one is at 30°...

-
These - or similar - are the only hard wire cutters I trust not to deform. I'm almost surprised when MT cutters don't deform. They just are not made to the same hardness and precision as the real thing.
-
Day 2. Tried the saw out on some 1" dowels. The shape of the saw was good for this type of cutting. Not too difficult to push and pull, with the most cutting done on the pull stroke. It does remove material on the push as well, just not nearly as much.
The large teeth didn't try to clog at any point cutting six of the dowel lengths. On the flip side, the large teeth can(and did) cause hand fatigue rather quickly. :ahhh
-
Nice start, guys. Eager to join you in a couple of days!
Sent from my iPhone using Tapatalk
-
Thanks Nix

Have a safe trip and can’t wait to have you joining us
-
Powernoodle Day 3

-
Day 3
Today I had to adjust the fan in the downstairs toilet
It stays on for 30 minutes after you leave the toilet
Which is to long :ahhh
So today I used the jewellers driver
to turn the adjuster down to 10 minutes
The length of the driver helped as the adjuster is set far back in the fan



-
@Wspeed said:
the fan in the downstairs toiletIt stays on for 30 minutes after you leave the toilet
Which is too long :ahhhIf you've ever had some of ThePeacent's cabbage and jalapeno casserole, you'll know that sometimes 30 minutes isn't enough.
Good one

I don’t think any fan would
be strong enough for TPs toilet
:D -
Nothing person, TP. Its that incredible Spanish cuisine.

-
**Day 3 **
From the bathroom to a bedroom. Door handle retainer plate was reported loose. PAD to the rescue. The medium screwdriver on the cap lifter's end is not bad at all, sits well in the screw head slot.
Later tonight I shall use the cap lifter for its intended purpose

Come to think of it, or rather of the can opener: I don't think I have any old-fashioned cans anymore, only those with quick-pull tabs...


Sent on my SM-G930F with Tapatalk
-
I have the same problem with bottles
Most of them now have screw tops
And not the old cap lifter anymore :ahhh :ahhh -
Back to the short saw... I've found a spare ST300 saw in my parts bin which is making me think...


Edit: and the file, too. The ST300's file is both longer and better than the one on the PAD. Hmmm...
Sent on my SM-G930F with Tapatalk
-
@Dutch_Tooler said:
Back to the short saw... I've found a spare ST300 saw in my parts bin which is making me think...
Sent on my SM-G930F with Tapatalk
That looks a lot more usable D_T

Have you got a spare file as well
As that could make the PAD more useful
-
Early pros and cons for me, subject to change:
<u>Pros</u>
- compound leverage pivot is one of the best features on any MT; I knew that a long time ago
- outside opening tools for quick deployment
- real 3D phillips with adequate reach
- it has a saw
- 1/4" driver
- hard wire cutter ate a 10d nail with no problem
<u>Cons</u>
- overall cheap feel
- flimsy main blade; a longer saw could have been used
- tools can accidentally deploy past 180 degrees; no big deal, but not a sign of tight engineering and quality
- file appears to be almost non-functional, but more data is required. Did SOG think we wouldn't notice?
- jewelry driver, can open and cap lifter are unnecessary; space could have been used for scissors
- phillips shank is offset which limits reach in countersunk holes
Current Powernoodle Dynamic Assessment Rating ("CPDAR"): 5/10
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login