Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
@gerleatherberman said:
DT,
Unfortunately we knew before buying the PADs/PAs that the file would be garbage. Plus, if you rub the file on soft material very hard, it will remove material....Technically...
SOG SHOULD offer to make and send out correctly machined files for anyone willing to pop one in their PAD. I wouldn't pay the shipping and/or wait for weeks to let SOG do it. The damn thing was too expensive to start with.
Thanks GLBM... well, technically I had no idea the file would not even be a file, even if news had not been encouraging to start with...
The fact that material is removed when you apply the "file" does not actually count. I guess the only, minimal, scraping action is due to the edges where the sides of the grooves meets the top surface not being entirely clean, due to sloppy application of the cut. That does not make it a file.
Anyhow, I agree, I'd settle for a proper replacement file for free too, no problem.

-
Powernoodle Day 4

The saw is short, but adequate. Most of the cutting is accomplished on the pull stroke.
-
Day 4
Today I was working on my daughters old
mountain bike as it’s to small for her now
So it’s time to sell the bike
The seat is on the highest level it can go
So I had to put the seat back downI used the bolt grippers to undo the nut
Than pushed the seat back down
And tightened the nut back up with the bolt grippersOn the last pic you can see the pliers
after use and no damage to the teethI am very impressed with the pliers so far
As I was expecting to see some marks on the pliers




-
@Wspeed said:
I am very impressed with the pliers so farMe too. The pliers/cutter/compound leverage is far and away the best part of this MT. It equals or exceeds the utility of the competition. The only improvement might be the addition of replaceable cutters.
That would be nice, as long as they don’t become weak

-
Yeah, many folks prefer the non-replaceable cutters on the Gerbers, for example, as being less prone to fracture than the replaceable cutters. I would prolly rather deal with the replaceable flavor than ding up the non-replaceable version and have to file it out.
-
As long as they make them stronger than I wouldn’t mind

-
@Wspeed said:
I am very impressed with the pliers so farMe too. The pliers/cutter/compound leverage is far and away the best part of this MT. It equals or exceeds the utility of the competition. The only improvement might be the addition of replaceable cutters.
some argue that with the added leverage and gripping power the cutters would be easily broken off and abused :ahhh
@powernoodle said:
Yeah, many folks prefer the non-replaceable cutters on the Gerbers, for example, as being less prone to fracture than the replaceable cutters.I do. Gerber's carbide cutters are like SOG's newer files, that is, cr*p

That’s a shame TP :ahhh :ahhh
Have you got a pic of the braided wire you cut
well, actually yes I have. :D After all the drama to cut that d*rn wire I sure was going to keep it

Next to a Rambler and Spirit for size reference, is just what I had laying on the table

Thanks TP

You would think that it is ok to cut wire
Are you going to send it to SOG for warranty
no unfortunately not,
SOG hasn't been very friendly or open to sending things overseas to me in previous comms, even through European dealers and for a price :P so warranty repairs are completely off the table
-
Chris@SOG got back to me today
To say that he will ask the engineers
What they class as soft wire and hard wire
And will get back to meI emailed Chris back and mentioned about the
file quality. As soon as I get a email
I will let you all know what he said
-
A thought on the finish, which seems to be subject to some criticism...
Of course polished or BO would be nicer. However, one can say that the current kind of matte finish has some advantages as well - it's less slippery than polished steel and less prone to reflecting light, so less conspicuous (if you want to be covert) while still being light-coloured enough to find if dropped in the underbrush (unlike BO). Just my 2 €c... -
I like the finish of the PAD
It’s something a bit different
-
Old grill is falling apart. Temporary fix: new bolts. I'll add washers and cut the excess off when I don't feel lazy.
The PAD pliers did well on these small-medium nuts/bolts.

-
Day 5
Loose car floor mat re-tightened with the large flat screwdriver bit in the integral bit grip. Nice thought to add a magnet so as not to lose the bit should you accidentally release the grip.

Sent on my SM-G930F with Tapatalk
-
Got a email from Chris@SOG and this is what he wrote
I don’t have a good answer for you on the file. I’ve alerted Engineering and hopefully that will address the issue.
Here is the answer I got from one of our engineers
As a general rule, if it is non-structural (or not intended to sustain mechanical loads) it is soft wire. One example is copper electrical wire with plastic insulation. If it deoes sustain mechanical loads it is hard wire. Example chicken wire.
Hopefully this helps out.
-
Powernoodle Day 5
*
The "file" on the PowerAccess Deluxe is so poorly made as to be virtually non-functional. It would not smooth out the rough spots on this plastic outdoor garbage bin.* -
I like the finish of the PAD
If I really liked the PAD, I would probably really like the stonewashed finish. But as I pretty much dislike the PAD, it stinks up what I think about the finish.
Current Powernoodle Dynamic Assessment Rating ("CPDAR"): 4/10
I take it you don’t like the PAD then powernoodle

-
@Wspeed said:
Got a email from Chris@SOG and this is what he wroteI don’t have a good answer for you on the file. I’ve alerted Engineering and hopefully that will address the issue.
Here is the answer I got from one of our engineers
As a general rule, if it is non-structural (or not intended to sustain mechanical loads) it is soft wire. One example is copper electrical wire with plastic insulation. If it deoes sustain mechanical loads it is hard wire. Example chicken wire.
Hopefully this helps out.
Thanks Wspeed... a bit noncommittal on the file, that answer

@powernoodle said:
Powernoodle Day 5
*
The "file" on the PowerAccess Deluxe is so poorly made as to be virtually non-functional. It would not smooth out the rough spots on this plastic outdoor garbage bin.*I am not surprised, you won't be surprised to hear. It confirms what I surmised above based on my visual inspection and comparison with real files... The grooves are too shallow and narrow to form actual teeth between them, as should be the case for any file that deserves the name.
Note: the challenge checklist mentions "Find an imaginative use for this tool", as if the authors were somewhat hesitant to use the name bestowed upon it by SOG >:D
-
Yes not the answer we wanted about the file :ahhh
But if someone is going to take this seriously
We might get better tools in the future
And I could still get a reply back from Chris
Ones they have had a look at the file
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login