Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
That’s no problem GLBM

What I mean is that when I look at the crunch or Supertool
Like the screw drivers they are just a straight bit of metal
With the end ground down a bit so it fits a screw
They work fine but just aren’t made very niceI just feel that MT company’s concentrates more
On the pliers than their tools that goes in the models
-
@gerleatherberman said:
Your PAD file, from comparing photos, is MUCH more poorly machined than the file on my PAD.Yeah, and that pic is of the double-cut or "good" side.
Can the file on yours even smooth a fingernail?
No, neither side would shape a fingernail.
I do not begrudge a maker too much for allowing something to slip through CQ. But this is a design or manufacturing problem (a design problem, really) that is endemic to this MT. I don't think the file was ever intended to work because the design, even if perfectly executed in manufacturering, would still be more akin to a butter knife than a file.
Yeah, I could have continued to test the other tools. But if you know that you are going to break up with a lass, you might as well get it over now and move on. And my return window was closing.
I have be honest and say that it feels real good to have a Swisstool Spirit in my pocket. I might switch to an ST300 to get the endorphins going.
I hate not participating in this one, but God willing I will be around for future Challenges because I love MTO and love my toys. I think maybe there at least 2 Challenges starting in July.
-
@Wspeed said:
That’s no problem GLBM
What I mean is that when I look at the crunch or Supertool
Like the screw drivers they are just a straight bit of metal
With the end ground down a bit so it fits a screw
They work fine but just aren’t made very niceI just feel that MT company’s concentrates more
On the pliers than their tools that goes in the models
The OG ST and Crunch are very old designs from LM(the Crunch is still produced and has not been changed much since 1999). Perhaps something during or after the Kick\Fuse\Blast\Core era would be better to compare to. :)
@gerleatherberman said:
Your PAD file, from comparing photos, is MUCH more poorly machined than the file on my PAD.Yeah, and that pic is of the double-cut or "good" side.
Can the file on yours even smooth a fingernail?
No, neither side would shape a fingernail.
I do not begrudge a maker too much for allowing something to slip through CQ. But this is a design or manufacturing problem (a design problem, really) that is endemic to this MT. I don't think the file was ever intended to work because the design, even if perfectly executed in manufacturering, would still be more akin to a butter knife than a file.
Yeah, I could have continued to test the other tools. But if you know that you are going to break up with a lass, you might as well get it over now and move on. And my return window was closing.
I have be honest and say that it feels real good to have a Swisstool Spirit in my pocket. I might switch to an ST300 to get the endorphins going.
I hate not participating in this one, but God willing I will be around for future Challenges because I love MTO and love my toys. I think maybe there at least 2 Challenges starting in July.
I would hope SOG could rectify the problem, but their track record is abysmal at best, with cancelling the model being their solution with troublesome models(ex. PowerGrab and PowerDuo). However, all my rambling aside, I'll reserve judgement for the PAD until I see how they react to the file abomination.
I have to agree that SOG knew that the file on the Access series was terrible at best, and pointless to include, in the case of the PAD you received. It could be that SOG is having financial issues and pushed the product, even knowing it was faulty. Not an excuse though and seems self-defeating at best.

See ya around this thread, powernoodle!

-
GLBM Day 5:
Used cutters to cut a computer power cable, chew off the jacket, and strip the three wires.
Bonus shot of my checklist. :)



-
Day 6
Desktop fan (powered by USB outlet on PC screen) had become really wobbly. Its pivots are secured by rather undersized Phillips screws... but tightening these with the PAD helped a bit (let's see for how long).

Edit: the possibility to use standard 1/4" bits is IMHO one of the best aspects of the PAD, and so is the way it's solved in a flexible manner with both a grip mount integrated in the pliers and the separate stub for the bit adapter; both variants have a magnet holding the bit in place. The stub has stops at 90° and 180°.
Word of caution: the stub for the bit adapter is formed rather like the 2D bits from Leatherman, and thus likely to have similar torque resistance, which is inferior to that of a normal 1/4" bit/socket combination. If you have to apply a lot of torque, avoid the stub and adapter and instead use the bit grip on the pliers (see e.g. my Day 5 post). The compound leverage of the pliers is of great help. -
Back to the "file" for a moment, if I may.
The pics below show the extent of the catastrophe on my PAD, in support of what I have described earlier.
This echoes what Powernoodle and Wspeed have concluded, and I wish SOG would take note and issue a statement with some reassurance on how they will address the issue.

Nevertheless, at this point it is the only major gripe I have with the PAD.
The somewhat flimsy blades have been mentioned, and while I agree with the sentiment, I think it is the best they could have done based on the geometry chosen for the handles, and the lock springs in particular, short of redesigning said geometry. The blades could not have been made wider and still fit inside the handles without interfering with the lock springs...
-
Day 6
Today I had to tighten the handle on the drawer
And the best fitting for the screws is the small driver
A job well done



-
Here are some pics of the file from my PAD
Well a bit of scratched metal
you can’t call it a file




-
I'm finally ready to start........
Day 01:
Used the knife to conduct the initial paper cutting test. I did strop the blade first. Very sharp, cleanly sliced fine catalog paper. Good start here!

-
I'm carrying the PAD in it's belt pouch, but took out the bit set.
The bit set is just a bit bulky (sorry for the unintentional pun there). This is a bit odd (ok, there I go again), since the bit driver capability is the real strength of the PAD. Perhaps after I've adjusted to carrying the PAD, I'll try adding the bits back into the sheath.
As I said in a previous thread, I find that the sheath is not well designed to carry both the bits and PAD, but it works just fine for the PAD alone.
-
It think the smurfed-up file is just going to be one of those issues for SOG. Huge FAIL and it should be an embarrassment for them.
SOG: FIX the FILE (or leave it out in favor of some SCISSORS)!!!

-
Nice to have you back again Nix

-
Awesome challenge gents! best of like guys.
-
Thanks dtt nice one

-
I'm glad to get this challenge underway!

-
Howdy Nix! Awesome to have you in the challenge!

Day 6:
Two pics. One is me pulling a small-medium brass nail out of painted oak. Two is my using the integrated hex driver in the back of the pliers. I didn't like the plier-hex idea on the PowerPlay and still don't like it on the PowerAccess Deluxe. But, figured I give it a go for the challenge. Works, but constant squeezing is required. :ahhh

-
Day 01 (continued):
Used the saw to cut down a small Aspen tree. This past Winter was tough and the deer ate anything they could. We had a small Aspen tree growing in the yard, but it had been mauled too badly to leave standing. Had to go.
PAD saw made quick work of cutting the soft wood, and the "tree" was felled in no time. Roots got dug up with a shovel.

-
Day 7
PAD's compound leverage pliers to the rescue intervening in a repair following a typical office accident involving destruction of a sprung badge holder reel. The repairs involved putting my preferred black leather badge holder on a new reel - I hate these clunky plastic badge holders

Edit: glad you could join us Nix


PS for some reason the pic is invisible...??? Although I am pointing to a file uploaded with Tapatalk.
-
Day 7
Today I tested the Plain blade
I have some different size silicone reinforced hoses
And a piece of garden hose to useI was surprised how easy the blade cut the silicone hoses
But when I tried the garden hose it wasn’t that easy
I had to put a lot of pressure and saw motions to cut the hoseI will test the blade on more things to see if it is still sharp
Tried to shave hair off my arm like I tried before and worked
But this time the blade couldn’t shave the hair off my arm
So it’s not as sharp now as it was first use


-
@Dutch_Tooler said:
Day 7PAD's compound leverage pliers to the rescue intervening in a repair following a typical office accident involving destruction of a sprung badge holder reel. The repairs involved putting my preferred black leather badge holder on a new reel - I hate these clunky plastic badge holders

Edit: glad you could join us Nix


PS for some reason the pic is invisible...??? Although I am pointing to a file uploaded with Tapatalk.
Could see the pic earlier today, so something has happened [emoji53]
Sent fra min FRD-L09 via Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login