Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Back to the "file" for a moment, if I may.
The pics below show the extent of the catastrophe on my PAD, in support of what I have described earlier.
This echoes what Powernoodle and Wspeed have concluded, and I wish SOG would take note and issue a statement with some reassurance on how they will address the issue.

Nevertheless, at this point it is the only major gripe I have with the PAD.
The somewhat flimsy blades have been mentioned, and while I agree with the sentiment, I think it is the best they could have done based on the geometry chosen for the handles, and the lock springs in particular, short of redesigning said geometry. The blades could not have been made wider and still fit inside the handles without interfering with the lock springs...
-
Day 6
Today I had to tighten the handle on the drawer
And the best fitting for the screws is the small driver
A job well done



-
Here are some pics of the file from my PAD
Well a bit of scratched metal
you can’t call it a file




-
I'm finally ready to start........
Day 01:
Used the knife to conduct the initial paper cutting test. I did strop the blade first. Very sharp, cleanly sliced fine catalog paper. Good start here!

-
I'm carrying the PAD in it's belt pouch, but took out the bit set.
The bit set is just a bit bulky (sorry for the unintentional pun there). This is a bit odd (ok, there I go again), since the bit driver capability is the real strength of the PAD. Perhaps after I've adjusted to carrying the PAD, I'll try adding the bits back into the sheath.
As I said in a previous thread, I find that the sheath is not well designed to carry both the bits and PAD, but it works just fine for the PAD alone.
-
It think the smurfed-up file is just going to be one of those issues for SOG. Huge FAIL and it should be an embarrassment for them.
SOG: FIX the FILE (or leave it out in favor of some SCISSORS)!!!

-
Nice to have you back again Nix

-
Awesome challenge gents! best of like guys.
-
Thanks dtt nice one

-
I'm glad to get this challenge underway!

-
Howdy Nix! Awesome to have you in the challenge!

Day 6:
Two pics. One is me pulling a small-medium brass nail out of painted oak. Two is my using the integrated hex driver in the back of the pliers. I didn't like the plier-hex idea on the PowerPlay and still don't like it on the PowerAccess Deluxe. But, figured I give it a go for the challenge. Works, but constant squeezing is required. :ahhh

-
Day 01 (continued):
Used the saw to cut down a small Aspen tree. This past Winter was tough and the deer ate anything they could. We had a small Aspen tree growing in the yard, but it had been mauled too badly to leave standing. Had to go.
PAD saw made quick work of cutting the soft wood, and the "tree" was felled in no time. Roots got dug up with a shovel.

-
Day 7
PAD's compound leverage pliers to the rescue intervening in a repair following a typical office accident involving destruction of a sprung badge holder reel. The repairs involved putting my preferred black leather badge holder on a new reel - I hate these clunky plastic badge holders

Edit: glad you could join us Nix


PS for some reason the pic is invisible...??? Although I am pointing to a file uploaded with Tapatalk.
-
Day 7
Today I tested the Plain blade
I have some different size silicone reinforced hoses
And a piece of garden hose to useI was surprised how easy the blade cut the silicone hoses
But when I tried the garden hose it wasn’t that easy
I had to put a lot of pressure and saw motions to cut the hoseI will test the blade on more things to see if it is still sharp
Tried to shave hair off my arm like I tried before and worked
But this time the blade couldn’t shave the hair off my arm
So it’s not as sharp now as it was first use


-
@Dutch_Tooler said:
Day 7PAD's compound leverage pliers to the rescue intervening in a repair following a typical office accident involving destruction of a sprung badge holder reel. The repairs involved putting my preferred black leather badge holder on a new reel - I hate these clunky plastic badge holders

Edit: glad you could join us Nix


PS for some reason the pic is invisible...??? Although I am pointing to a file uploaded with Tapatalk.
Could see the pic earlier today, so something has happened [emoji53]
Sent fra min FRD-L09 via Tapatalk
-
Day 7
PAD's compound leverage pliers to the rescue intervening in a repair following a typical office accident involving destruction of a sprung badge holder reel. The repairs involved putting my preferred black leather badge holder on a new reel - I hate these clunky plastic badge holders

Edit: glad you could join us Nix


PS for some reason the pic is invisible...??? Although I am pointing to a file uploaded with Tapatalk.
Could see the pic earlier today, so something has happened [emoji53]
Sent fra min FRD-L09 via Tapatalk
Seems to be happening to more members today

-
-
Here are some pics of the file from my PAD
Well a bit of scratched metal
you can’t call it a file
That looks like a movie prop. Not a real file, but it could fool viewers.
It’s absolutely unacceptable

-
Good luck with the challenge again guys... how are you liking your SOGs so far?
D_T, for some reason, Tapatalk is smurfing all the pics uploaded... I’m having the same problem too... might want to re-upload via your mobile browser...
-
Thanks jaya

The SOG PAD is doing ok so far
It’s just the file, it’s a bit of a joke
:ahhh
I won’t say it’s a good or bad tool
Until the challenge is finished
As there are a lot more tasks to complete
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login