Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Nice shots and uses today, guys!

Day 03:
Used the X-small driver to tighten up my reading glasses. Worked well.

-
Powernoodle Day . . . uh, never mind.
After turning into Mr. Grumpy because of the PAD's "file" and general cheapy feel (IMO) - and then joyfully returning it to Amazon - I looked at MT alternatives in the PAD's general price range. Just for giggles. On eBay you can get a new Swisstool for $86.16 shipped, which is $16.21 more than the PAD on Amazon Prime. Well worth the extra cost. The PAD gives you the bit drivers (eh), 1/4" driver and compound leverage pivot not found on the Swisstool, but the Swisstool is in virtually all other respects much the superior MT. Again, IMO. The PAD and Swisstool are pretty much at the opposite end of the spectrum when looking at quality, precision, etc. Or if you want to stick with SOG, the PowerLock can be had on Amazon Prime for $47.77 shipped, which is $22.18 less than the PAD. The venerable PowerLock gives you the same (and awesome) compound leverage and 1/4" driver of the PAD, albeit with inside opening tools. It does have those goofy wings that slow deployment of the tools, but the PowerLock is a legit competitor at $47. Someone, maybe Nix, noted that the PAD's sheath just does not work well with the driver set, which competes for space against the MT. Another inelegant design element.
So whether competing internally with the PowerLock, or going up against the class leaders like the Swisstool, one is hard-pressed in my view to advocate the PAD. This is especially true when embracing the sad reality that SOG obviously does not care if all of the tools on the PAD function as advertised. So Mr. Grumpy here is more saddened by SOG the company than the PAD itself. Its not the poor PAD's fault that it cannot keep up with the other kids.
-
@powernoodle said:
So Mr. Grumpy here is more saddened by SOG the company than the PAD itself.I share those sentiments. I want to love SOG, but they make it hard. I've had girlfriends like that......but not for long.
And, yes, I'm bummed out by the poorly designed sheath. Another sign of poor project development and oversight. I think somebody needs to be fired.
Today the naked PAD is riding in the back pocket of my jeans. This is actually my new favorite carry method for the PAD.....which is a bit sad in it's own right...... Maybe I'll try to make a leather sheath for it.
Hmmmm......
-
Day 8:
Getting used to the quirkiness of the PAD. Now that is has been performing every task I have used it for, without issue, I cannot say it feels cheap anymore("not as nicely/well made as others" would be more applicable).
A few positive note:
The half-ground drivers of the PAD perform slightly better than the high-polished drivers on some other MTs. The tools are easy to deploy(not requiring fingernails) and the cutter section on the pliers is superb(size and design). The plier head itself has proven to be as good as some older SOG plier heads.
The sheath isn't great, but it has worked as advertised. For me it has anyway.If the SOG had included a proper file on the PAD, I believe overall opinion would differ to some large degree.

-
@gerleatherberman said:
If the SOG had included a proper file on the PAD, I believe overall opinion would differ to some large degree.Agreed. That file.......

Otherwise, doing nicely so far.
Although the sheath does need a re-design in my opinion. Not even much of redesign. 5 minutes, maybe 10 minutes with a designer, and the sheath is easily improved. A few simple tweaks and it's a really nice sheath. Part of what kills me here is that SOG is sooooo close to making a good, perhaps great, multitool. 30 minutes with the design team, a little shouting, one kick in the a$$, and I think I can get the PAD is ready for the majors.
But, right now? I wish this were the Super Tool 300 challenge.........
-
Agreed, Nix.

But, a point nobody is bringing up. The PAD is a bit over 1oz lighter than the SwissTool. Making it much lighter than the ST300. :)
The PAD is 8.733oz(247.8g). Impressively light weight for the function and pliers you get.

-
Hey, fair point.
It does carry fairly well in a back pocket or the sheath.
No complaints there.

-
It does carry fairly well in a back pocket or the sheath.
No complaints there.

+1
Back to the sheath - my opinion so far:
Pros:- room for the PAD and the bit kit in the main pocket (if a bit tightly) leaving the side loop free
- Molle attachment allows flexible carry options
Cons:
- bulk - quite a bulge on the hip if carrying PAD and bit kit in the main pocket
- if not, PAD very loose in main pocket, plus awkward fit of bit kit in side loop
- velcro is of abysmal quality, only barely holds shut on Day 9. Usable quality would have added maybe 5 cents to production costs
- sloppy stitching in places downgrades overall perception of quality
- a second side loop or pocket would have been nice and again only added 5 cents to production costs...
-
I don’t like pouches they are always in the way
Especially when sitting down or driving a car
The pouch could of been a lot better if they put a
Decent quality popper on the front like the one on the back
I really like the popper on the back for the belt
So you don’t have to undo your belt to fit / remove the pouch
I am wearing the pouch every day for the challenge
So I might get used to the pouch
-
Day 04:

Day four getting started here. Just checking in with the challenge team. I know we've identified some strong negative points, no surprises there, that doesn't take an MTo'er very long. At this point, I'm interested in seeing what the capabilities of the PAD are, and trying to get a sense for how effective some of the tools are. And durability is also a point of interest.
I'm going to slide from this challenge into an all summer-long challenge. I know some of you can't do that, but I want to give this tool a really good look. There is a lot to like here, and I'm curious to see if, with extended use, I'll become more attached to the PAD.
-
Day 9
I have just finished changing the handbrake cable
On my friends LandRover Defender TD5
This was a 4 hour job as you have to remove the prop shaft
Before you can get to the handbrake drum on the gearbox
I used the PAD pliers to remove springs of the pads
And to hook the new cable over the brake arm
Unfortunately my hands were covered in grease to take pics
So as the last job was to fit the cable to the handbrake
And fit a split pin my hands were clean enough to get a couple
Of pictures fitting the split pin to the handbrake cableThe PAD performed as it should no problems




-
Now we're cooking!
Already used the kit to drive a new screw in the scale bracket at work. :)
-
Day 9
Lounge chair repairs with the bolt grip portion of the pliers. Not in pic, other hand holding locknut with a wrench/spanner, since I happen to have only two hands :D

-
Nice pic, DT!
It does show one of the downsides to the compound leverage system though. Handle splaaaaayyyyyy. :ahhhPAD hanging out on an old wagon wheel hub.

-
Nice pic GLBM

-
@gerleatherberman said:
Nice pic, DT!
It does show one of the downsides to the compound leverage system though. Handle splaaaaayyyyyy. :ahhhPAD hanging out on an old wagon wheel hub.
Thanks GLBM - that is intrinsic in the system I guess... hasn't hit me negatively so far :D
-
Day 04 (continued):
It turned out to be a big day for the SOG PAD. I was outside doing a lot of yard-work today and the PAD saw a lot of action. I used the main blade to open a couple more bags of mulch, but didn't take a picture since that has been shown by me already.
However, we have a small herd of deer that occasionally makes raids into our yard and are very destructive. In early Fall, I put protective fencing up to keep the deer away from trees and some shrubs. Here's a snapshot of a tree that was badly damaged when the previous owner didn't protect the trunk from rutting bucks who like to use the trees as scent posts:

And you can also see my solution, wire netting. Mrs Nix would not permit the use of barbed wire or claymore mines.
In summer the deer aren't a problem, so I take the wire fencing down. This requires the removal of all the tie-wire I used to bind the edges of the wire fencing together. And I really cinched that wire tight. So here is where the PAD came in today. I used the pliers tips to grab and twist the wire out of the fencing. I also used the PAD to cut the wire as needed, usually when it got too kinked up.

The PAD was extremely handy for this task since I was using both the pliers and the integrated wire cutters.
At the end of the day, PAD 50, Wire 0.

But the PAD wasn't done. I decided to run a semi-permanent, short hose from the side of the house through Mrs Nix's shrub garden. I wanted the hose to be very secure at the external faucet, so I used a little plumber's tape and really cranked down on the hose nut to get a tight seal.
Now, with this size nut, the handles were splayed too far apart to use with one hand, but the PAD worked well using a two handed approach.

This was one of those moments where I was glad to have a multitool in my pocket, and the PAD worked really well here.
And just the same, I noticed my flag pole bracket was a little loose. Since the PAD was in my pocket, I pulled out the Phillips driver and tightened the screws up a bit. The PAD's driver is a #2, and these bolts are probably #3's, but the PAD did the job just fine.

So, a busy day for the PAD.....and there may be more in store......
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login