Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Agreed, Nix.

But, a point nobody is bringing up. The PAD is a bit over 1oz lighter than the SwissTool. Making it much lighter than the ST300. :)
The PAD is 8.733oz(247.8g). Impressively light weight for the function and pliers you get.

-
Hey, fair point.
It does carry fairly well in a back pocket or the sheath.
No complaints there.

-
It does carry fairly well in a back pocket or the sheath.
No complaints there.

+1
Back to the sheath - my opinion so far:
Pros:- room for the PAD and the bit kit in the main pocket (if a bit tightly) leaving the side loop free
- Molle attachment allows flexible carry options
Cons:
- bulk - quite a bulge on the hip if carrying PAD and bit kit in the main pocket
- if not, PAD very loose in main pocket, plus awkward fit of bit kit in side loop
- velcro is of abysmal quality, only barely holds shut on Day 9. Usable quality would have added maybe 5 cents to production costs
- sloppy stitching in places downgrades overall perception of quality
- a second side loop or pocket would have been nice and again only added 5 cents to production costs...
-
I don’t like pouches they are always in the way
Especially when sitting down or driving a car
The pouch could of been a lot better if they put a
Decent quality popper on the front like the one on the back
I really like the popper on the back for the belt
So you don’t have to undo your belt to fit / remove the pouch
I am wearing the pouch every day for the challenge
So I might get used to the pouch
-
Day 04:

Day four getting started here. Just checking in with the challenge team. I know we've identified some strong negative points, no surprises there, that doesn't take an MTo'er very long. At this point, I'm interested in seeing what the capabilities of the PAD are, and trying to get a sense for how effective some of the tools are. And durability is also a point of interest.
I'm going to slide from this challenge into an all summer-long challenge. I know some of you can't do that, but I want to give this tool a really good look. There is a lot to like here, and I'm curious to see if, with extended use, I'll become more attached to the PAD.
-
Day 9
I have just finished changing the handbrake cable
On my friends LandRover Defender TD5
This was a 4 hour job as you have to remove the prop shaft
Before you can get to the handbrake drum on the gearbox
I used the PAD pliers to remove springs of the pads
And to hook the new cable over the brake arm
Unfortunately my hands were covered in grease to take pics
So as the last job was to fit the cable to the handbrake
And fit a split pin my hands were clean enough to get a couple
Of pictures fitting the split pin to the handbrake cableThe PAD performed as it should no problems




-
Now we're cooking!
Already used the kit to drive a new screw in the scale bracket at work. :)
-
Day 9
Lounge chair repairs with the bolt grip portion of the pliers. Not in pic, other hand holding locknut with a wrench/spanner, since I happen to have only two hands :D

-
Nice pic, DT!
It does show one of the downsides to the compound leverage system though. Handle splaaaaayyyyyy. :ahhhPAD hanging out on an old wagon wheel hub.

-
Nice pic GLBM

-
@gerleatherberman said:
Nice pic, DT!
It does show one of the downsides to the compound leverage system though. Handle splaaaaayyyyyy. :ahhhPAD hanging out on an old wagon wheel hub.
Thanks GLBM - that is intrinsic in the system I guess... hasn't hit me negatively so far :D
-
Day 04 (continued):
It turned out to be a big day for the SOG PAD. I was outside doing a lot of yard-work today and the PAD saw a lot of action. I used the main blade to open a couple more bags of mulch, but didn't take a picture since that has been shown by me already.
However, we have a small herd of deer that occasionally makes raids into our yard and are very destructive. In early Fall, I put protective fencing up to keep the deer away from trees and some shrubs. Here's a snapshot of a tree that was badly damaged when the previous owner didn't protect the trunk from rutting bucks who like to use the trees as scent posts:

And you can also see my solution, wire netting. Mrs Nix would not permit the use of barbed wire or claymore mines.
In summer the deer aren't a problem, so I take the wire fencing down. This requires the removal of all the tie-wire I used to bind the edges of the wire fencing together. And I really cinched that wire tight. So here is where the PAD came in today. I used the pliers tips to grab and twist the wire out of the fencing. I also used the PAD to cut the wire as needed, usually when it got too kinked up.

The PAD was extremely handy for this task since I was using both the pliers and the integrated wire cutters.
At the end of the day, PAD 50, Wire 0.

But the PAD wasn't done. I decided to run a semi-permanent, short hose from the side of the house through Mrs Nix's shrub garden. I wanted the hose to be very secure at the external faucet, so I used a little plumber's tape and really cranked down on the hose nut to get a tight seal.
Now, with this size nut, the handles were splayed too far apart to use with one hand, but the PAD worked well using a two handed approach.

This was one of those moments where I was glad to have a multitool in my pocket, and the PAD worked really well here.
And just the same, I noticed my flag pole bracket was a little loose. Since the PAD was in my pocket, I pulled out the Phillips driver and tightened the screws up a bit. The PAD's driver is a #2, and these bolts are probably #3's, but the PAD did the job just fine.

So, a busy day for the PAD.....and there may be more in store......
-
**Day 04 **(continued):

OK, the can opener works, but it's poorly designed and manufactured. The grinds are terrible. The design allows one to punch through the can lid, but it doesn't cut as cleanly as a Victorinox can-opener.
I'm a little annoyed, because as I was opening this small can of tomato sauce--pizza night!--the can opener kept punching through and splattering tomato sauce over the counter and my shirt. And, as you can see, the lid got depressed into the sauce. Not cool.
I think the opener works best by taking tiny bites and moving it forward in a counter-clockwise direction. This seems to limit the splatter problem. Backwards, or clock-wise, was a bit faster, but I had less control and more splatter.
Overall, I'm giving this can-opener 3 of 5 points. It works, but I'd rather use Leatherman or Vic or Gerber opener. Hell, I've used combat knives that were better at opening cans.
This challenge requires 3 uses of the can opener. It will be interesting to see if I get any better at using this can-opener and get better results with subsequent uses.
-
Awesome putting to use of the PAD, Nix!

SOG can openers are notoriously lame. The SOG can opener has been pretty much unchanged for twenty years.

The earlier SOG can openers were similar to LM can openers and worked better.I realize now that I don't have any traditional style cans or bottles. Mine are all pull tab. I am going to have to buy canned food and capped glass bottle sodas for the can-opener and cap-lifter tests.

-

Well, you may find something new to enjoy!

-
Well, you may find something new to enjoy!


I tried out the small driver on the can opener on my older multi-meter. Worked great in adjusting it and removing the back to check the batteries. Changed the AA and the 9V was good. Not sure what the graphic on the 9V is about and do not remember putting it in there.

Maybe my older brother put that battery in when he borrowed it a few years ago. :P
Then I was just playing around with the PAD's 1/4" driver. :D



-

Well, you may find something new to enjoy!


I tried out the small driver on the can opener on my older multi-meter. Worked great in adjusting it and removing the back to check the batteries. Changed the AA and the 9V was good. Not sure what the graphic on the 9V is about and do not remember putting it in there.

Maybe my older brother put that battery in when he borrowed it a few years ago. :P
Then I was just playing around with the PAD's 1/4" driver. :Dthat battery

also, Nix posted his attempt with the tomato can that was a bit messy,
but the result of the final work was flawless! :ahhh Look what he cooked: :o
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login