Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
To pile on the tests, I tried four unused SOGs (US and China). Left to right: PowerPlier, PowerLock(pre-patent early), PowerLock(newer 2.0), PowerGrab, and PAD.
The PAD was the only one that failed to cut the same jumper wire from earlier. :-\
-
Day 18
I owe y'awl a checklist... see below.
Intrigued by the cutting tests and the mixed results I have tested the cutters on my PAD again, see 2nd pic.
Results are mostly positive: zip tie and thin earphone wire PASS, garden wire (see earlier test, I call it chicken wire) PASS, but thin braided nylon wire FAIL as this simply folds up between the jaws. This is OK I think, for that I'd prefer a blade anyway.


-
Thank you for the checklist and testing the cutters, D_T!
Looks like your cutters are excellent. I would never think many cutters could cut braided nylon (that stuff is like cutting thread).
So, as it stands, the order of best to worst reported cutters is: D_T, glbm, and Nix.
Hopefully W will report on his PAD cutters. :) -
@gerleatherberman said:
My results show that the cutters on my PAD are not quite as sloppy as yours, but mine did worse than I had anticipated.
Most of my other test subjects didn't do well either, so I can't quite condemn my PAD cutters just yet. (See chart attached) I will be checking the cutters periodically to see if they get any worse. The PowerLock I tested is my oldest and most used SOGs with lots of pliers-slop and the PAD didn't do much better. You can look at the images to see how well each cut was. Each wire was cut once with no twisting or pulling. I used the mid section of each tool's cutters and allowed two cuts for small cutters(one cut per side) on the 12g. wire.

I have individual images of each tool/wire results if anyone needs them.
So if I understand the chart, the PAD got more passes than the Swisstool and Wave, and the Surge was the only one to get three passes.

-
I didn’t have any problems cutting anything I tried

But I will have one more go at testing
more wire of different sizes and thicknessesI will post my results later

-
Day 18
Today I was checking the fluid levels in the engine bay
And needed something to open the power steering cap
Normally I use a large screwdriver but as I got the PAD
I found the file to be just right for removing the cap


-
In my book that qualifies as an imaginative use, Wspeed 
-
That’s what I thought as well

-
@Dutch_Tooler said:
In my book that qualifies as an imaginative use, Wspeed 
+1
just beware that files (if we can call this one a file ::) :D) are usually hardened so should not be used to pry, twist or torque as they easily snapped
but I see that you used it putting the force closer to the pivot thus reducing the leverage multiplication effect 
-
cutting test
I used the SOG PAD and PA
And the LM Crunch and the LM Supertool
For this test I have 8 different type wires
I started with the really thin wire copper and metal
Then had 4 different thickness of electrical wire
The brown wire has a solid copper wire
And 2 different size trimmer wireThe first 2 pics is what I tested the MTs with
The PAD and PA both didn’t have any
problems cutting the 8 different size wiresOnly the LM Crunch didn’t cut the
green trimmer wire on one of the cuts


-
The PAD
Cut everything no problems


-
The PA
Cut everything no problems


-
The LM Crunch
Only had one cut on the green
trimmer wire it had a problem with

-
The LM Supertool
No problems
I have just about tested
everything I can with the SOG PAD
On day 11 I tested zip ties stainless
welding wire and a hardened 2.5mm nail
As well as trimmer wire and electric wire
And again for the 2nd test it cut everything


-
In my book that qualifies as an imaginative use, Wspeed 
+1
just beware that files (if we can call this one a file ::) :D) are usually hardened so should not be used to pry, twist or torque as they easily snapped
but I see that you used it putting the force closer to the pivot thus reducing the leverage multiplication effect 
Good point D_T I do think anything
tighter and it would of snapped off
-
Nice testing, guys!
(And D_T, good work with the checklist. Your cap-lifter is clearly well tested.
)I scrounged up a few extra bits of wire to test, will post a pic later.

-
@Don Pablo said:
So if I understand the chart, the PAD got more passes than the Swisstool and Wave, and the Surge was the only one to get three passes.
Indeed. It seems strange, but remember, the tests involved no twisting or pulling while using the cutters on stranded wire & tiny solid core wire(these were intentionally chosen, because they are notoriously aggravating to cut) Every tool tested can cut most stuff when "manipulated" a bit.
And don't be put-off my results. I needed a standard of testing and obviously most of us don't cut stuff exactly the same way.Usually, when I cut zip ties, electrical wire and thin steel wire, I angle and pull the wire up towards the cutter blade(i just cut straight on in the the tests). This makes for cleaner cuts and reduces strain on the jaw pivot. Every tool I have will cut most stuff this way.
Non of the tools tested would need this kind of manipulation with thicker (or stronger) materials like bailing wire.Pic of what I mean attached at bottom. The pic is showing a powerpint, because I am having my off-day coffe and can't be bothered to go get the pad right now. :P
Today I was checking the fluid levels in the engine bay
And needed something to open the power steering cap
Normally I use a large screwdriver but as I got the PAD
I found the file to be just right for removing the capI think you win most creative file use.

And thank you for doing all of your testing. Seems your PAD has an excellent cutter section!


-
Can we agree that Gerbers replaceable cutters suck? :)
-
Thanks GLBM

If there is anything else you would like
me to test the cutters with let me knowSo far the cutters have cut everything i can think of
The pliers on my PAD seem to be good quality
-
@Don Pablo said:
Can we agree that Gerbers replaceable cutters suck? :)Hell yes. They have to be the worst cutter system ever designed. Everything from my early replaceable-cutter MP600 to my Center-Drive look like piranhas when I try to cut wire with them.
You saw the chart. The Gerber failed all three. And if you look at the photos, it barely tore the jackets off of the wire.
The CD isn't as bad as that mp600, but it is definitely at the bottom of the totem-pole(sp?).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login